Bedienungsanleitung Exabyte 007-3086-001

42 Seiten 0.34 mb
Download

Zur Seite of 42

Summary
  • Exabyte 007-3086-001 - page 1

    8505XL 8-mm T ape Drive Owner ’s Guide Document Number 007-3086-001 ...

  • Exabyte 007-3086-001 - page 2

    8505XL 8-mm T ape Drive Owner ’s Guide Document Number 007-3086-001 CONTRIBUTORS W ritten by Pablo Rozal Illustrated by Dan Y oung and Cheri Br own Edited by Christina Cary Production by Derrald V ogt Engineering contributions by Roy Hughes, Robert Clark, Dale W itt, Bill Y ergin Cover design and illustration by Rob Aguilar , Rikk Carey , Dean Ho ...

  • Exabyte 007-3086-001 - page 3

    iii Contents List of Figures v List of T ables vii About This Guide ix Typographical Conventions x 1. Installation 1 Products that Support the 8505XL 1 Preparing for Installation 2 Ensuring ESD Protection 2 Unpacking the Tape Drive and Saving the Materials 3 Checking the Tape Drive Accessories 3 Installing the Tape Drive 3 Setting the SCSI ID 3 Con ...

  • Exabyte 007-3086-001 - page 4

    iv Contents 2. Operating the T ape Drive 17 Reading the LEDs 17 Selecting Data Cartridges 19 Write-Protecting a Data Cartridge 20 Loading a Data Cartridge 20 Unloading a Data Cartridge 21 Resetting the Tape Drive 21 3. Preventive Maintenance 23 Recommended Cleaning Cartridges 23 Determining When to Clean the Tape Drive 23 Using the Cleaning Cartrid ...

  • Exabyte 007-3086-001 - page 5

    v List of Figur es Figure 1-1 Removing/Installing the Drive From/On the Drive Sled 5 Figure 1-2 Setting the SCSI ID (Default Setting Shown) 6 Figure 1-3 Setting the Drive Sled for Single-Ended Operation 8 Figure 1-4 Installing the Tape Drive Into a Horizontal Drive Bay 10 Figure 1-5 Installing the Tape Drive Into a Vertical Drive Bay 11 Figure 1-6 ...

  • Exabyte 007-3086-001 - page 6

    vi ...

  • Exabyte 007-3086-001 - page 7

    vii List of Tables T able 1-1 Problems and Possible Solutions 15 T able 2-1 LED States and Interpretations 18 T able 2-2 8505XL Tape Capacity 19 T able A-1 Drive Specifications 31 ...

  • Exabyte 007-3086-001 - page 8

    viii ...

  • Exabyte 007-3086-001 - page 9

    ix About This Guide This guide helps you set up, install, and operate the 8505XL tape drive. The 8505XL uses 8-mm format tapes and installs in most of the existing Silicon Graphics© systems and data storage units that support single-ended, front-loading drives (FLDs). Note: For a list of products that curr ently support the 8505XL tape drive, see ...

  • Exabyte 007-3086-001 - page 10

    x About This Guide T ypographical Conventions These type conventions and symbols ar e used throughout this guide: Italics Filenames, variables, IRIX ® command ar guments, command fl ags, titles of publications, icon names. Screen type Code examples, fi le excerpts, and scr een displays (including error messages). Bold Screen type User input. () ...

  • Exabyte 007-3086-001 - page 11

    1 Chapter 1 1. Installation This chapter provides information for the following tasks: • preparing for installation • installing the tape drive • installing the software driver Note: The 8505XL requir es either IRIX 5.3, 6.1 or later software. If your system already has IRIX 6.1, softwar e driver installation is not requir ed. • testing you ...

  • Exabyte 007-3086-001 - page 12

    2 Chapter 1: Installation Preparing for Installation T o prepar e for installation, follow the steps described in this chapter . 1. Ensure ESD pr otection (see “ Ensuring ESD Protection ” on page 2). 2. Unpack the tape drive and save the packing materials (see “ Unpacking the T ape Drive and Saving the Materials ” on page 3). 3. Check the t ...

  • Exabyte 007-3086-001 - page 13

    Installing the Tape Drive 3 Unpacking the T ape Drive and Saving the Materials Carefully r emove the tape drive from its box. Save all the original packaging materials in case you need to reship the tape drive. The tape drive ’ s packaging helps protect the tape drive fr om shock, vibration, moisture, and electrostatic dischar ge (ESD). Checking ...

  • Exabyte 007-3086-001 - page 14

    4 Chapter 1: Installation Before setting the tape drive ’ s SCSI ID, determine the SCSI IDs of all the other SCSI devices currently attached to your bus (for example, a har d drive or a CD-ROM reader). Caution: SCSI ID 0 is reserved for the system contr oller and cannot be used. The tape drive is shipped with the SCSI ID set to 6 . If you ar e in ...

  • Exabyte 007-3086-001 - page 15

    Installing the Tape Drive 5 1. Remove the four screws that secur e the drive to the bottom of the mounting sled (see Figure 1-1) and set them aside. Figure 1-1 Removing/Installing the Drive Fr om/On the Drive Sled 2. Remove the drive adapter and power cables fr om the 8505XL (see Figure 1-1) and then place the drive on an anti-static surface. 3. Lo ...

  • Exabyte 007-3086-001 - page 16

    6 Chapter 1: Installation Figure 1-2 Setting the SCSI ID (Default Setting Shown) 4. Using a pair of fl at-nose pliers, slide the small plastic jumpers over the pins on the jumper block to obtain the desir ed address. Extra jumpers are shipped in a separate bag. Save the unused jumpers in case you need to select a differ ent SCSI ID later . Caution ...

  • Exabyte 007-3086-001 - page 17

    Installing the Tape Drive 7 7. Install the four screws that secur e the bottom of the drive to the drive sled (see Figure 1-1). Configuring the Drive Sled for Single-Ended Operation The 8505XL drive sled assembly houses a SCSI channel adapter boar d. Y ou must ensure that the drive sled assembly is set to single-ended operation. Caution: Use prope ...

  • Exabyte 007-3086-001 - page 18

    8 Chapter 1: Installation Figure 1-3 Setting the Drive Sled for Single-Ended Operation Note: Y our system disk should always be set to SCSI ID 1. Be sur e each SCSI device on a bus has a unique SCSI addr ess (ID). The SCSI bus cannot function properly if mor e than one device has the same SCSI ID. T erminating the SCSI Bus The internal SCSI channel ...

  • Exabyte 007-3086-001 - page 19

    Installing the Tape Drive 9 Follow these instructions to install a half-height fr ont-loading device: Installing Into a Horizontal Drive Bay Follow these instructions to install the drive into a horizontal drive bay . 1. Orient the FLD and sled assembly so that the connectors on the back ar e on the bottom half of the drive and face away fr om you ...

  • Exabyte 007-3086-001 - page 20

    10 Chapter 1: Installation Figure 1-4 Installing the T ape Drive Into a Horizontal Drive Bay Slide drive lever left to lock sled Drive lever in locked position ...

  • Exabyte 007-3086-001 - page 21

    Installing the Tape Drive 11 Figure 1-5 Installing the T ape Drive Into a V ertical Drive Bay Drive sled Drive ...

  • Exabyte 007-3086-001 - page 22

    12 Chapter 1: Installation T urning On Power to the T ape Drive When power is applied to the 8505XL, watch for the following: • All three of the tape drive ’ s LEDs light. • The tape drive ’ s 30-second power -on self-test begins. • When the self-test is complete, the top and bottom LEDs turn of f; the middle LED is off or fl ashes irr e ...

  • Exabyte 007-3086-001 - page 23

    Installing the Tape Drive 13 1. Locate a data cartridge that does not contain any valuable information and make sure that its write-pr otect switch is set to write-enable (see Figure 1-6). 2. Gently push the data cartridge as shown (in Figur e 1-7) until the load mechanism pulls the cartridge into the drive. Figure 1-6 W rite-Enable/Disable Switch ...

  • Exabyte 007-3086-001 - page 24

    14 Chapter 1: Installation Figure 1-7 Loading a Data Cartridge 3. W ait while the tape drive loads the tape, determines the tape format, and positions the tape to the logical beginning of the tape (LBOT). This takes about 45 seconds. When the gr een LED is on solid, the tape drive is ready . ...

  • Exabyte 007-3086-001 - page 25

    Installing the Tape Drive 15 4. Perform a backup operation to write a small amount of data to the tape (see your IRIX administration documentation, as r equired). 5. Rewind the tape and read the data written in step 4 and compar e it to the original. This determines whether the softwar e and tape drive are functioning properly . If problems occur , ...

  • Exabyte 007-3086-001 - page 26

    16 Chapter 1: Installation ...

  • Exabyte 007-3086-001 - page 27

    17 Chapter 2 2. Operating the T ape Drive This section includes information about the following: • reading the tape drive ’ s LEDs • selecting data cartridges • setting the write-protect switch on the data cartridge • loading and unloading a data cartridge Reading the LEDs The tape drive uses three LEDs (Figur e 2-1) to indicate its opera ...

  • Exabyte 007-3086-001 - page 28

    18 Chapter 2: Operating the Tape Drive Figure 2-1 8505XL Front Panel Note: Y ou may occasionally observe LED combinations and sequences not described in T able 2-1. These other combinations r epresent special or unusual conditions that are beyond the scope of this table. T able 2-1 LED States and Interpr etations LED State T op LED (errors) Middle ...

  • Exabyte 007-3086-001 - page 29

    Selecting Data Cartridges 19 Note: The LEDs fl ash at differ ent speeds to distinguish between states: • slow fl ash = 1 fl ash/second • fast fl ash = 4 fl ashes/second • Irregular fl ash = rate of fl ash varies with SCSI bus activity . If the device is not connected to the bus, the LED is of f. Selecting Data Cartridges Silicon Graphi ...

  • Exabyte 007-3086-001 - page 30

    20 Chapter 2: Operating the Tape Drive Note: The EXA T APE 160-m XL data cartridges contain a r ecognition system stripe located on the tape leader for media identi fi cation. The 8505XL uses this stripe to distinguish data-quality metal-particle media, such as EXA T APE, from other 160-m media. T o maintain data integrity , the 8505XL automatical ...

  • Exabyte 007-3086-001 - page 31

    Unloading a Data Cartridge 21 Unloading a Data Cartridge The unload button is the only operating contr ol on the tape drive. It is used to unload the data cartridge from the tape drive (see Figur e 2-2). Note: Y ou can use the unload button to clear some har dware err ors. If a hardwar e error occurs, press the unload button to r eset the tape driv ...

  • Exabyte 007-3086-001 - page 32

    22 Chapter 2: Operating the Tape Drive ...

  • Exabyte 007-3086-001 - page 33

    23 Chapter 3 3. Pr eventive Maintenance The only routine maintenance r equired by the tape drive is r egular cleaning of the tape drive heads and tape path. Pr oper storage and maintenance of your data cartridges maximizes the shelf life of your tapes and assur es data integrity . Recommended Cleaning Cartridges Silicon Graphics recommends that you ...

  • Exabyte 007-3086-001 - page 34

    24 Chapter 3: Preventive Maintenance Using the Cleaning Cartridge T o use the cleaning cartridge, follow these steps: 1. Make sure that the tape drive is on and has r un the power-on self-test in T able 2-1 in Chapter 2. 2. Remove any data cartridge from the tape drive. 3. Check the cleaning cartridge to see if ther e is suf fi cient cleaning mate ...

  • Exabyte 007-3086-001 - page 35

    Caring for Data Cartridges 25 Caring for Data Cartridges T o maximize the shelf life of your tapes and assur e data integrity , follow these guidelines when storing data cartridges: • Place a label or other refer ence information on the cartridge adjacent to the write-protect switch. On the label, you may want to include the cartridge number (log ...

  • Exabyte 007-3086-001 - page 36

    26 Chapter 3: Preventive Maintenance Replacing Data Cartridges Approximately once each year , you may want to r ead all information on a tape and check the read err or statistics. If errors have incr eased signi fi cantly since the previous test or if they exceed a certain pr edetermined threshold, you should rear chive the data to a new tape and ...

  • Exabyte 007-3086-001 - page 37

    27 Chapter 4 4. T r oubleshooting This chapter provides suggestions for solving pr oblems that may occur when you are installing and operating your tape drive. These suggestions are divided into the following sections: • problems with tape drive installation • problems with the tape drive operation Often you can solve a tape drive problem by tr ...

  • Exabyte 007-3086-001 - page 38

    28 Chapter 4: Troubleshooting Problems With T ape Drive Operation Most problems with tape drive operation occur with impr oper cartridge use. If you have been successfully operating your backup softwar e and tape drive in the past, but are now experiencing pr oblems reading and writing data, check the following: • If you are writing data, make su ...

  • Exabyte 007-3086-001 - page 39

    Problems With Tape Drive Operation 29 If you are experiencing operating pr oblems loading or unloading a data cartridge, check the following: • Make sure that your system is turned on. If the system is of f, the tape drive may not eject the data cartridge. • The tape drive may have experienced a har dware err or . Press the unload button to cle ...

  • Exabyte 007-3086-001 - page 40

    30 Chapter 4: Troubleshooting ...

  • Exabyte 007-3086-001 - page 41

    31 Appendix A A. T ape Drive Speci fi cations T able A-1 shows the speci fi cations for the 8505XL tape drive. T able A-1 Drive Speci fi cations Parameter Speci fi cations Interface SCSI-1 and SCSI-2, single-ended Capacity 8200 format 262 KB/sec 8200c format Note: This assumes a 2:1 compr ession ratio 500 KB/sec 8500 format 500 KB/sec 8500c for ...

  • Exabyte 007-3086-001 - page 42

    32 Appendix A: Tape Drive Specifications Power and Reliability Input voltages Standard + 5 VDC and +12 VDC 5% Power consumption 14.5 W Mean time between failur e 160,0000 hours at 10% duty cycle T able A-1 (continued) Drive Speci fi cations Parameter Speci fi cations ...

Produzent Exabyte Kategorie Computer Drive

Dokumente, die wir vom Produzenten des Geräts Exabyte 007-3086-001 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Exabyte
- Bedienungsanleitungen 007-3086-001
- Produktkarten Exabyte
- Informationsbroschüren
- oder Energieetiketten Exabyte 007-3086-001
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Exabyte 007-3086-001.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Exabyte 007-3086-001, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Exabyte 007-3086-001. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Exabyte 007-3086-001 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Exabyte 007-3086-001, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Exabyte 007-3086-001 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Exabyte 007-3086-001 verständlich ist.

Eine gänzliche Bedienungsanleitung von Exabyte sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Exabyte 007-3086-001 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Exabyte 007-3086-001 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Exabyte 007-3086-001, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Exabyte 007-3086-001 - die uns die ersten Schritte während der Nutzung von Exabyte 007-3086-001 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Exabyte 007-3086-001 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Exabyte 007-3086-001 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Exabyte 007-3086-001?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Exabyte 007-3086-001 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Exabyte 007-3086-001 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)