-
MTD 390 Shown - page 1
IMPORTANT: Read safety rules and instructions carefully before operating equipment. MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 Front Tine Tillers Models 340 Thru 390 PRINTED IN U.S.A. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or ...
-
MTD 390 Shown - page 2
2 TABLE OF CONTENTS Content Page Important Safe Operation Practices ................................................................... 3, 4 Assembling Your Tiller ....................................................................................... 5 Know Your Tiller ............................................................................... ...
-
MTD 390 Shown - page 3
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES This Symbol Points Out Important Safety Instructions Which, If Not Followed, Could Endanger The Personal Safety And/or Property Of Yourself And Others. Read And Follow All Instructions In This Manual Before Attempting To Operate Your Tiller. Failure To Comply With These Instructions May Result In Pers ...
-
MTD 390 Shown - page 4
4 CHILDREN • Tragic accidents can occur if the operator is not alert to the presence of small children. Children are often attracted to the tilling activity. Never assume that children will remain where you last saw them. • Keep children out of the work area and under the watchful eye of a responsible adult other than the operator. • Be alert ...
-
MTD 390 Shown - page 5
5 SECTION 2: ASSEMBLING YOUR TILLER NOTE: This operator’s guide covers three different model tillers. Models 340 thru 345 have forward tine drive only. Model 390 has both forward and reverse tine drive. Follow only the instructions which pertain to your model tiller. See the model plate on your tiller for the correct model number. IMPORTANT: This ...
-
MTD 390 Shown - page 6
6 Figure 3 Attaching Clutch Control Cable(s) Forward Cable Attach the end of the forward cable to the bracket underneath the handle assembly as follows. (On model 390, the forward clutch cable is the cable which is attached closer to the rear of the tiller). • Loosen the hex nut on the threaded rod near the end of the cable, and move it up the ro ...
-
MTD 390 Shown - page 7
7 Final Clutch Adjustment To check the clutch cable adjustment, proceed as follows. • Disconnect the spark plug wire and move it away from the spark plug to prevent accidental starting. • Engage and release the tine engagement handle, then the reverse tine engagement lever (model 390 only). If an excessive noise is heard when releasing either t ...
-
MTD 390 Shown - page 8
8 Choke Lever (Model 340/390) The choke lever is located above the throttle control. It is used to enrich the fuel mixture when starting a cold engine. See Figure 8. Primer Button (Model 345) The primer button is located behind the air cleaner. It is used to enrich the fuel mixture in the carburetor when starting a cold engine. See Figure 8 Forward ...
-
MTD 390 Shown - page 9
9 • Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. Do not let starter handle snap back against starter. • Repeat preceding instructions 5 and 6 until engine starts. When engine starts, move choke lever on engine halfway between CHOKE and RUN. • Move throttle control to IDLE pos ...
-
MTD 390 Shown - page 10
10 Controlling Speed And Tilling Depth • Wheel Yoke Adjustment: Place wheel yoke so that the wheels are forward (nearest point between wheels and tines) for shallow tilling, cultivating and transport. The forward speed will increase. Turn yoke around (farthest point between wheels and tines) for deep tilling. Forward speed will decrease. See Figu ...
-
MTD 390 Shown - page 11
11 Throttle Control: The throttle control lever adjusts the engine speed and stops the engine. With the throttle control lever pushed completely forward, the carburetor is in START position. Pulling the throttle control back slightly adjusts the engine speed to FAST. Pulling the throttle back further reduces the engine speed to SLOW. Pull the throt ...
-
MTD 390 Shown - page 12
12 SECTION 5: MAKING ADJUSTMENTS WARNING: Disconnect the spark plug wire and ground against the engine before performing any adjustments, repairs, or maintenance. Tine Width Adjustment The tilling width of the unit is 22 inches. See Figure 15. Tilling width can be increased to 24 inches by removing the clevis pins and hairpin clips, sliding the out ...
-
MTD 390 Shown - page 13
13 SECTION 6: MAINTAINING YOUR TILLER Lubrication WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on tiller. Pivot Points- Remove the belt cover and lubricate all moving parts and pivot points at least once a season using SAE 30 engine oil. Chain Drive- The chain case is pre-lubricat ...
-
MTD 390 Shown - page 14
14 Figure 18 • Reassemble the new belt, following instructions in reverse order. Make certain the reverse drive belt is assembled with the wide side of the belt against the transmission and engine pulleys. Be certain to adjust the clutch control as instructed in the final clutch adjustment section of assembly instructions. Forward Drive Belt See ...
-
MTD 390 Shown - page 15
15 SECTION 8: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel. Throttle control lever not in correct starting position (if so equipped). Blocked fuel line. Dirty aircleaner. Choke not in ON position. Spark plug wire disconnected. Faulty spark plug. Engine flooded. Fill tank wit ...
-
MTD 390 Shown - page 16
16 Model 340 Thru 345 1 2 3 4 2 5 6 8 9 10 7 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 25 32 25 38 39 40 41 42 43 44 48 47 45 50 49 46 Standard Briggs & Stratton Tecumseh Engines ...
-
MTD 390 Shown - page 17
17 Model 340 Thru 345 Ref. No. Part No. Part Description 1. 712-0442 Acorn Lock Nut 1/4-20 2. 736-3020 Flat Washer .271” I.D. x .630” O.D. 3. 731-1599 Handle Cover 4. 712-0287 Hex Nut 1/4-20 Gr.2 5. 720-0274 Grip-Handle 6. 686-0083 Clutch Handle Assembly 7. 720-0269 Grip-Clutch 8. 710-0641 Hex Bolt 1/4-20 x 2.25” Lg. Gr.5 9. 731-1645A Clutch ...
-
MTD 390 Shown - page 18
18 Model 340 Thru 345 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 19 20 21 22 23 24 25 27 26 28 29 30 31 32 33 34 35 37 36 38 39 40 42 41 ...
-
MTD 390 Shown - page 19
19 Model 340 Thru 345 Ref. No. Part No. Part Description 1. 712-0392 Hex L-Stop nut 1/4-28 2. 736-3020 Flat Wash. .266” I.D. x .625” O.D. 3. 710-0599 Hex Washer Screw 1/4-20 x .5” 4. 711-0920 Belt Cover Bolt 5. 712-3004A Hex Flange Top L-Nut 5/16-18 6. 710-0723 Hex Hd. Scr. 3/8-16 x 1.25” Lg. 7. 756-0313 Fl-Idler 2.12” O.D. 8. 786-0149 Id ...
-
MTD 390 Shown - page 20
20 Model 390 1 2 3 4 5 6 2 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 30 37 30 43 44 45 46 47 48 49 50 51 52 53 54 55 Standard Briggs & Stratton Tecumseh Engines ...
-
MTD 390 Shown - page 21
21 Model 390 REF. NO. PART NO. DESCRIPTION 1 712-0442 Acorn Lock Nut 1/4-20 2 736-3020 Flat Washer .271” I.D. x .630” O.D. 3 720-0270A Reverse Handle Grip 4 731-1600 Handle Cover w/o throttle 5 710-0779A Truss Mach. Scr. #10 x 1/2” Lg. 6 720-0274 Grip-Handle 7 712-0287 Hex Nut 1/4-20 Gr.2 8 726-0135 Cap Speed Nut 9 686-0083 Clutch Handle Asse ...
-
MTD 390 Shown - page 22
22 Model 390 3 17 18 21 19 16 43 44 46 47 4 5 7 11 2 1 6 8 9 10 15 14 45 38 41 22 40 42 36 39 33 12 13 30 29 32 31 34 35 28 27 49 48 25 26 24 24 23 20 50 51 ...
-
MTD 390 Shown - page 23
23 Model 390 REF. NO. PART NO. DESCRIPTION 1 712-0392 Hex L-Stop nut 1/4-28 2 736-3020 Flat Wash. .266” I.D. x .625” O.D. 3 710-0599 Hex Washer TT-Tap Scr. 1/4-20 x .5” 4 711-0920 Belt Cover Bolt 5 712-3004A Hex Flange Top L-Nut 5/16-18 (Gr.5) 6 710-0723 Hex Hd. Scr. 3/8-16 x 1.25” Lg. (Gr.5) 7 756-0313 Fl-Idler 2.12” O.D. 8 786-0149 Idle ...
-
MTD 390 Shown - page 24
MANUFACTURER’S LIMITED WARRANTY The limited warranty set forth below is given by MTD PRODUCTS INC (“MTD”) with respect to new merchan- dise purchased and used in the United States, its posses- sions and territories. MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of or ...
Haben Sie eine Frage bezüglich MTD 390 Shown?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit MTD 390 Shown nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit MTD 390 Shown hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.