-
Delta 22-610 - page 1
INSTRUCTION MANUAL P ART NO. 428-08-651-0001 06-1 5 -05 Copyright © 2005 Delta Machinery 24 3 / 4 " Planer (Model 22-610, Thr ee Phase) T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...
-
Delta 22-610 - page 2
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...
-
Delta 22-610 - page 3
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...
-
Delta 22-610 - page 4
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...
-
Delta 22-610 - page 5
5 ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE fr om your supervisor , instructor , or another q ...
-
Delta 22-610 - page 6
6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...
-
Delta 22-610 - page 7
7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gaso- line or lacquer thinner for this purpose). After cleaning, cover the unpainted surfac ...
-
Delta 22-610 - page 8
8 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE - 2-3 hours * Open end wrenches (supplied) * Hex wrenches (supplied) * Flat screwdriver (not supplied) UNLOADING AND POSITIONING MACHINE This machine should be unloaded using a crane and slings around and under the table on both sides, as shown in Fig. 2. Lift the machine slowly , making ...
-
Delta 22-610 - page 9
9 T o connect power to your machine, proceed as follows for either 200-230/460 volts, three phase operation. 1. Remove the four screws, one of which is shown at (A) Fig. 4, and remove cover (B). 2. Insert power line through entrance hole (E) and con- nect the three power lines to terminals L1, L2 and L3 (shown at C). The green gr ound wire should b ...
-
Delta 22-610 - page 10
10 OPERA TION OPERA TIONAL CONTROLS AND ADJUSTMENTS ST ARTING AND STOPPING THE PLANER The machine is started by pressing the gr een (shroud- ed) "ON" button (A) and stopped by pressing the r ed (mushroom type) "OFF" button (B), as shown in Fig. 8. Fig. 8 T ABLE RAISING AND LOWERING CONTROLS DISCONNECT MACHINE FROM POWER SOURCE F ...
-
Delta 22-610 - page 11
11 Fig. 12 T o change feed roll speeds, make sure the feed r oll engagement lever (A) Fig. 12, is disengaged (in the down position) and open the left side door of the machine. When the belt (C) is on the smallest step of the motor pulley (D) and the lar gest step of the gearbox pulley (E), the feed roll speed will be 25 feet per minute. When the be ...
-
Delta 22-610 - page 12
12 Fig. 16 Fig. 17 Fig. 18 CHECKING AND ADJUSTING BEL T TENSION DRIVE BEL T TENSION: Proper drive belt tension is obtained when there is zer o deflection, using light finger pressur e, on drive belts (A) Fig. 16, midway between pul- leys. If an adjustment is necessary , push down on lever (B) Fig. 16, to disenguage feed roller . Loosen jam nut (C) ...
-
Delta 22-610 - page 13
13 CHECKING, ADJUSTING AND REPLACING KNIVES 1. When checking, adjusting or replacing the cutter- head knives on the planer , proceed as follows: A. DISCONNECT MACHINE FROM POWER SOURCE B. Remove the top cover of the planer exposing the cutterhead. C. Check all four knives for pr oper setting using the knife guage (A), as shown in Fig. 20. When the ...
-
Delta 22-610 - page 14
14 Fig. 21 Fig. 22 Fig. 22A LEVELING THE T ABLE The table must be parallel to the cutterhead knives. T o check and adjust, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the four screws that attach the top cover to the planer and carefully r emove the top cover . 3. Place a straight edge (A) Fig. 21, on the ground sur- faces ...
-
Delta 22-610 - page 15
15 Fig. 23A Fig. 23B Fig. 23D Fig. 23C CHECKING AND ADJUSTING BED ROLL HEIGHT The height of the bed rolls (A) and (E) Fig. 23A, should be set between .002" and .004" above the table surface, with the bed rolls at their lowest position. T o check the infeed bed roller height setting, pr oceed as follows: 1. DISCONNECT MACHINE FROM POWER SO ...
-
Delta 22-610 - page 16
16 Fig. 24B Fig. 25 Fig. 26 ADJUSTING PRESSURE BAR IMPORT ANT : TH E PRESSURE BAR IS SET A T THE F ACTOR Y AND SHOULD NOT NEED ASJUSTMENT . BUT WHEN KNIVES ARE SHARPENED OR REPLACED THE PRESSURE BAR SETTING SHOULD BE CHECKED AND ADJUSTED IF NECESSAR Y . The pressur e bar is located directly behind the cutter- head and rides on the planed surface of ...
-
Delta 22-610 - page 17
17 ADJUSTING THE CHIPBREAKER The chipbreaker is located on the top of the planer and extends down around the fr ont of the cutterhead. The chip-breaker segments raise as stock is fed thr ough and "break or curl" the chips the same as the plane ir on cap on a hand plane. The bottom of the chipbreaker must be parallel to the knives and set ...
-
Delta 22-610 - page 18
18 ADJUSTING SPRING TENSION ON FEED ROLLERS The outfeed roll (A) Fig. 33, and infeed r oll (not visible) are those parts of your planer that feed the stock while it is being planed. The feed rolls ar e under spring tension and this tension must be sufficient to feed the stock uni- formly through the planer without slipping but should not be too tig ...
-
Delta 22-610 - page 19
19 Fig. 38 Fig. 39 Fig. 40 ADJUSTING CHIP DEFLECTOR 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the cutterhead guard. 3. The edge (C) of the chip deflector (A) Fig. 38, should be adjusted so it is a minimum of .040" and a maximum of .080" away from the cutting cir cle. Place a feeler gauge between the knife and the edge of the chip ...
-
Delta 22-610 - page 20
20 When using your machine, follow these few simple steps for achieving the best results. 1. T rue Up One Face – Feed one face of the board over a jointer , making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you planed in STEP 1 face down and feed the board thr ough the planer . Plane until ...
-
Delta 22-610 - page 21
21 P ARTS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...
-
Delta 22-610 - page 22
22 NOTES ...
-
Delta 22-610 - page 23
23 NOTES ...
-
Delta 22-610 - page 24
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...
Haben Sie eine Frage bezüglich Delta 22-610?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Delta 22-610 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Delta 22-610 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.