Bedienungsanleitung Honeywell 9700

32 Seiten 1.79 mb
Download

Zur Seite of 32

Summary
  • Honeywell 9700 - page 1

    Dolphin ® eBase Communication Cradle for the Dolphin ® 9700 Mobile Computer User’s Guide ...

  • Honeywell 9700 - page 2

    ...

  • Honeywell 9700 - page 3

    1 Introduction The Ethernet Base (eBase) enables a single Dolphin 9700 computer to communicate with a host device over an Ethernet network. We recommend use of Hone ywell peripherals, pow er cables , and power adapters. Use of an y non-Honeywell peripherals, cables , or power adapters ma y cause damage not cov ered by the warr anty . Unpacking the ...

  • Honeywell 9700 - page 4

    2 Software Requirements Before you connect the Dolphin terminal to the eBase, make sure you have the most current software installed. To check the terminal’s system information, tap Start > Power Tools > SysInfo . • The Kernel version must be 20.01 or later in terminals running Windows Mobile 6. 5 Classic. In terminals running Windows Mob ...

  • Honeywell 9700 - page 5

    3 Hard ware Over view Front P anel Terminal Well Place the terminal in this well to communicate with a host device, power the terminal, and charge the installed battery pack. The eBase completely charges the main battery in a Dolphin terminal in 4 hours. Auxiliary Battery Well See Auxiliary Battery Well on page 6. DOCK LED The Dock LED turns solid ...

  • Honeywell 9700 - page 6

    4 AUX Battery LED The AUX Battery LED indica tes the status of the battery charging in the auxiliary battery well; see Back Panel on page 6. COMM LED The COMM LED indicates the status of data transfer between the Dolphin terminal and the eBase. This color means… Orange The auxiliar y battery is charging. Green The auxiliar y battery has completed ...

  • Honeywell 9700 - page 7

    5 When the Dolphin terminal is docked: This color and status means… Red Solid No connection is established betw een the eBase and terminal. Orange Solid RASMan is attempting to establishing a connection between the eBase and the terminal. Green Solid RASMan has established a connection between the ebase and the terminal. USB Communication When th ...

  • Honeywell 9700 - page 8

    6 Back P anel Auxiliary Battery Well The eBase enables you to charge an additional Li-ion battery pack independently of the terminal well in 4 hours. This feature ensures that you can always have a fully charged battery for your terminal. When the Dolphin terminal is docked: This color and status means… Green Flashing Data is being transf erred b ...

  • Honeywell 9700 - page 9

    7 USB Port This USB Port is full-speed and 2.0 compliant. Using a USB cable, you can connect the eBase to a USB compliant device to facilit ate USB communication to and from the terminal. USB communication occurs through Microsoft ActiveSync (v4.5 or higher) or Microsoft Windows Mobile Device Center (WMDC) depending on the host workstation’s oper ...

  • Honeywell 9700 - page 10

    8 Bottom P anel For details on how to mount the eBase, see Mounting on page 25. Reset Button Compliance Label Serial Number Label ...

  • Honeywell 9700 - page 11

    9 Po w e r The terminal requires 9.5 Volts DC input for communications and battery charging; the power adapter on the power cable converts the voltage from the power source to 9.5 volts DC. Only the Honeywell 9.5 VDC, 4A power supply provided with the ebase converts the voltage appropriately. Honeywell recommends that you leave the eBase connected ...

  • Honeywell 9700 - page 12

    10 Charging the Main Battery in the Te r m i n a l We recommend use of Hone yw ell Li-Ion battery packs. Use of any non-Hone ywell batt ery may result in damage not cov ered by the warranty . The eBase provides power to the Dolphin terminal and allows the charging of the terminal’s main battery. The intelligent battery charging system incorporate ...

  • Honeywell 9700 - page 13

    11 Ethernet Communication Setting up the eBase 1. Plug the power cord into the power adapter. 2. Plug the power connector cable into the power connector on the back of the eBase. 3. Plug the A/C power cord into a standard wall outlet. The COMM LED flashes red. Note: When searching for a network, the 9700 terminal looks for a USB connection first, a ...

  • Honeywell 9700 - page 14

    12 3. Remove the check from the box next to, “ Synchronize all PCs using this connection” . Tap OK . 4. Insert a Dolphin terminal into the terminal well. The DOCK LED lights green. 5. On the Dolphin terminal, tap Start > Power Tools 6. Click the RASMan icon once. The terminal starts searching for a connection. Note: During the connection pr ...

  • Honeywell 9700 - page 15

    13 7. When the connection is established between the Dolphin terminal and the eBase, the terminal plays a sound, and the COMM LED on the eBase lights green. The connection icon in the Dolphin’s navigation bar changes from to . 8. Upon connection, the Dolphin terminal shares the eBase IP address. This IP address can be used by any application on t ...

  • Honeywell 9700 - page 16

    14 Displaying the eBase and T erminal IP Address Once the Dolphin terminal has be successfully connected to the eBase, the terminal shares the eBase IP address. 1. Tap Start > Power Tools > Network Utilities > IPConfig . 2. On the Input tab, tap the Display full configuration button. 3. The Dolphin terminal retrieves and displays the IP co ...

  • Honeywell 9700 - page 17

    15 7. Tap on Connection in the Key column, and then tap File > Disable . 8. Tap OK, and then tap Yes to save your changes. Modifying the RASMan A utoActiveSync Setting 1. Tap Start > Power Tools > EZConfig Utilities > RASMan . 2. Select Settings from the folder tree, and then tap AutoActiveSync under the Key column. 3. Tap Edit > Mod ...

  • Honeywell 9700 - page 18

    16 Configuring the Network By default, the eBase is conf igured to obtain IP addresses automatically via DHCP server. This means that in most cases you would simply pl ug-and-play the unit. If necessary, you can use the Cradle Manager configuration utility for dynamic network configuration. Accessing the eBase Cradle Manager from a Host Wo r k st a ...

  • Honeywell 9700 - page 19

    17 5. The Cradle Manager window opens. Note: Under General Settings, t he HTTP Port defaults to 80. ...

  • Honeywell 9700 - page 20

    18 Changing the P ass word You can change the password from the Cradle Manager window. 1. Under General Settings, select the check box next to, “ Change Password” . 2. Enter the new password in the New Password field. 3. Click Apply at the bottom of the screen. ...

  • Honeywell 9700 - page 21

    19 Changing the Dynamic Network Settings You can modify the Dynamic Network settings from the Cradle Manager window. 1. Under IP Settings, select Dynamic . 2. Enter the new settings in the fields supplied. Note: The default reboot time if missing an IP address is 60 seconds. 3. Click Apply at the bottom of the screen. Changing the Static Settings Y ...

  • Honeywell 9700 - page 22

    20 USB Communication Dolphin terminal’s support USB communication out of the box. The eBase also suppor ts USB communications using the USB port located on the back panel of the eBase. The eBase acts as a USB device by interfacing the USB signals of the Dolphin termina l to the USB of the host workstation. Using a standar d USB cable, the ebase? ...

  • Honeywell 9700 - page 23

    21 8. The connection icon in the Dolphin’s navigation bar changes from to it indicate a successful connection. The eBase c an now transfer data between the terminal and the host device. Switching fr om an Ethernet to USB ActiveSync Connection If you have trouble switching from Ethernet to USB ActiveSync mode, then RASMan may have disabled ActiveS ...

  • Honeywell 9700 - page 24

    22 2. Locate the reset button on the bottom of the eBase. 3. Push in and hold down the reset button. 4. While holding down the re set button, plug in the power cable. 5. Wait 15 seconds, and then release the button. Note: When the factory defaults are restored, the password reverts to the default password, < Dolphin >. Upgrading the eBase Fir ...

  • Honeywell 9700 - page 25

    23 2. Connect the host workstation Ethernet cable to a port on the same Ethernet subnet as the eBase. If the eBase is connected to a hub (or router), connect the host workstation to an available port on the same hub. 3. On your host workstation, open the web browser. 4. In the Address line, type the IP address assigned to the ebase, see Displaying ...

  • Honeywell 9700 - page 26

    24 8. Enter the IP address of the server in the TFTP Server IP Address field. 9. Under File Name , enter the eBase firmware upgrade file name. 10. Click Apply . 11. Click OK , when prompted to reboot the EULink bridge. The COMM LED on the eBase flashes red during the reboot process. 12. The COMM LED flashes orange during IP verification and the fir ...

  • Honeywell 9700 - page 27

    25 Mounting Set the eBase on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure to provide enough workspace with good lighti ng for the user to view and operate the Dolphin terminal while it is in the eBase. When choosing a location, bear in mind that: • the mounting location must allow users easy access to t ...

  • Honeywell 9700 - page 28

    26 T echnical Assistance Contact information for techni cal support, product service and repair can be found at www.honeywellaidc.com . Limited W arranty Refer to www.honeywellaidc.com/warranty_information for your product’s warranty information. Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specificat ...

  • Honeywell 9700 - page 29

    27 T rademarks Dolphin, eBase are trademarks or registered trademarks of Hand Held Products, Inc. or Honeywell International Inc. Microsoft, Windows, Windows Mobile, Windows XP, Windows Vista, Windows 7, Ac tiveSync, Windows Mobile Device Center, Outlook, and the Windows logo are trademarks or registered trademarks of the Microsoft Corporation. Oth ...

  • Honeywell 9700 - page 30

    ...

  • Honeywell 9700 - page 31

    ...

  • Honeywell 9700 - page 32

    Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com E-NETBA S E- UG R e v A 97-EBASE-UG Rev A 6/10 ...

Produzent Honeywell Kategorie Laptop

Dokumente, die wir vom Produzenten des Geräts Honeywell 9700 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Honeywell
- Bedienungsanleitungen 9700
- Produktkarten Honeywell
- Informationsbroschüren
- oder Energieetiketten Honeywell 9700
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Honeywell 9700.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Honeywell 9700, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Honeywell 9700. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Honeywell 9700 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Honeywell 9700, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Honeywell 9700 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Honeywell 9700 verständlich ist.

Eine gänzliche Bedienungsanleitung von Honeywell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Honeywell 9700 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Honeywell 9700 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Honeywell 9700, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Honeywell 9700 - die uns die ersten Schritte während der Nutzung von Honeywell 9700 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Honeywell 9700 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Honeywell 9700 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Honeywell 9700?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Honeywell 9700 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Honeywell 9700 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)