Bedienungsanleitung Taylor C004 - C007

54 Seiten 0.63 mb
Download

Zur Seite of 54

Summary
  • Taylor C004 - C007 - page 1

    MANUAL OF USE AND MAINTENANCE MANUEL D’UTILISATION ET D’ENTRETIEN MANUAL DE USO Y MANUTENCION MANUALE D’USO E MANUTENZIONE ...

  • Taylor C004 - C007 - page 2

    1 - ENGLISH ...

  • Taylor C004 - C007 - page 3

    ENGLISH - 2 The machine is covered by guarantee according to the conditions reported in the Seller’s In the following field, please write your machine serial number in capital letters In the following field, please write your machine serial number in capital letters Serial number Distributor’s stamp IMPORTANT We recommend to carefully and fully ...

  • Taylor C004 - C007 - page 4

    3 - ENGLISH Congratulations on purchasing a machine TAYLOR. The present manual, enclosed to the machine, is integrant and essential part of the machine and shall be delivered to the final user. Before performing any kind of operation, it is recommended to carefully study the reported instructions, as only a careful reading allows you getting the hi ...

  • Taylor C004 - C007 - page 5

    ENGLISH - 4 1 INSTALLATION 1.1 Preliminary inspection The machine travels at the customer’s ri sk. In case packing is damaged, immediately inform the carrier. Immediately inform the carrier also in case of damage to the mach ine, even if you open the packing a few days after the delivery. It is always advisable to accept the good SUBJECT TO INSPE ...

  • Taylor C004 - C007 - page 6

    5 - ENGLISH 1.6 Start-up In the tank a packet is present with the following components for assembly: sleeve, labyrinth, cock, drip collector. - Insert the sleeve into the apposite guide, until it reaches the pump inlet (pict1). Insert the labyrinth into the sleeve (pict 2), insert the spacer (only C007) - Mount the tap and turn it clockwise 45° (p ...

  • Taylor C004 - C007 - page 7

    ENGLISH - 6 2. OPERATION 2.1 Control panel, controls 1. ON/OFF button with leds indicating: “connected equipment under voltage” (right led), “machine enabled” (left led); 2. CLEAN: Led “machine under cleaning”; 3. DISPLAY showing: temper ature monitoring in the tank – alarms display – delivery time in seconds; 4. SET: Pushbutton to ...

  • Taylor C004 - C007 - page 8

    7 - ENGLISH - Avoid pouring the liquid cream on the pump, during tank filling - Make sure that sugar is well dissolved in cr eam to avoid that lumps obstruct the suction silicone hose - In any case, the addition of quantities of sugar superior to 8%-10% of the liquid cream is not recommended because it can limit the increase in volume. - Never add ...

  • Taylor C004 - C007 - page 9

    ENGLISH - 8 2. Press contemporaneously buttons “ON /OFF” and “SET”, on display will appear the temperature of the thermostat. 3. Keep “SET” pressed and press button “ON/O FF” to insert new temperature value. 4. Ones reached the new value, release bu tton “SET” and “ON/OFF” to store the data. 5. Start the machine pressing “ ...

  • Taylor C004 - C007 - page 10

    9 - ENGLISH Only by means of the “cream r egulator”, it is possible to hav e the correct air-liquid mix and therefore an excellent whipped cream. For a correct regulation, it is always advisable to start from position no. 1 and pr ogressively rotate the regulator towards the other positions until the desired product can be obtained. Different c ...

  • Taylor C004 - C007 - page 11

    ENGLISH - 10 3. MAINTENANCE During maintenance operations, never touch the machine with hands or tools without making sure that the machine is in STOP posit ion, the master switch is off and/or the multipolar plug disconnected. In case of troubles, make sure that they ar e not caused by a lack of servicing. On the contrary, ask for the intervention ...

  • Taylor C004 - C007 - page 12

    11 - ENGLISH wear, make it run only fo r the time necessary to cleaning . 4. Counterclockwise turn the tap to remove it: a) draw out the dispensing cock and disassemble it (pict 13); b) remove the sleeve by drawing it outwards and take the labyrinth out (pict 14); c) clockwise turn the pump to extract it from its seat. Accurately wash. 5. Disassemb ...

  • Taylor C004 - C007 - page 13

    ENGLISH - 12 4 . TROUBLE-SHOOTING TROUBLE POSSIBLE CAUSES REMEDIES Lack of power supply Check the presence of voltage in the mains The equipment does not work and the warning lights are off Automatic breaker tripped or power current fuses blown Send for the technician Machine not enabled Press the master switch ON/OFF until both warning lights ligh ...

  • Taylor C004 - C007 - page 14

    1 - FRAN Ç AIS ...

  • Taylor C004 - C007 - page 15

    FRAN Ç AIS - 2 La machine est sous garantie aux conditions illustrées par le vendeur. Veuillez bien indiquer dans le champ ci-dess ous le numéro d’immatriculation de votre machine Numéro d’immatriculation Cachet du concessionnaire IMPORTANT Nous vous recommandons de lire attentivem ent et entièrement ce manuel avant d’utiliser votre mach ...

  • Taylor C004 - C007 - page 16

    3 - FRAN Ç AIS Compliments ! Vous avez choisi une machi ne TAYLOR. Le présent manuel fourni avec cette machine doit être considéré comme une par tie intégrante et essentielle de celle-ci et il devra être remis à l’utilisateur final. Avant d’effectuer toute opérat ion, veuillez étudier attentivement les instructions qu’il contient : ...

  • Taylor C004 - C007 - page 17

    FRAN Ç AIS - 4 1 INSTALLATION 1.1 Inspection préliminaire La machine voyage aux risques et périls de l’acquéreur; si vous remarquez que l’emballage est abîmé, faites immédi atement une réserve au transporteur. Emettez également une réserve au transporteur tout de suite après le déballage, même s’il a lieu quelques jours après la ...

  • Taylor C004 - C007 - page 18

    5 - FRAN Ç AIS 1.6 Mise en marche Dans la cuve se trouve un emballage avec les composants suivants à assembler : tube, labyrinthe de tubes, robinet, recueille gouttes. - Insérer le tube dans la glissière prévue à cet effet, jusqu’à l’entrée de la pompe (fig.1). Insérer le labyrinthe dans le tube (fig.2) Insérer l’entretoise (seuleme ...

  • Taylor C004 - C007 - page 19

    FRAN Ç AIS - 6 2 . FONCTIONNEMENT 2.1 Tableau de contrôle, commandes 1. Bouton général ON/OFF avec voyant indiquant : “appareil branché et sous tension” (v oyant de droite), “machine habilitée” (voyant de gauche); 2. CLEAN : voyant “machine en phase de nettoyage”; 3. ECRAN indiquant : contrôle de température en cuve – affichag ...

  • Taylor C004 - C007 - page 20

    7 - FRAN Ç AIS - Éviter de verser de la crème liquide sur la pompe durant le remplissage de la cuve - contrôler que le sucre ait bien fondu dans la crème afin d’éviter que d’éventuels grumeaux ne bouchent le tuyau flexible d’aspiration de la pompe - les adjonctions de sucre supérieures à 8% -10% du poids de la crème liquide sont tou ...

  • Taylor C004 - C007 - page 21

    FRAN Ç AIS - 8 4. Atteint la valeur désirée, relâcher les button « SET » et « ON/OFF » pour momoriser le données. 5. Allumer la machine en appuyant le button « ON/OFF » (led gauche s’allume) 2.5 Affichage des alarmes Si cette légende apparaît à l’écran, elle indique “ sonde en panne court-circuitée ”. Dans ces deux cas, il f ...

  • Taylor C004 - C007 - page 22

    9 - FRAN Ç AIS C’est seulement en agissant sur le “régulateur de crème” qu’il est possible d’obtenir le juste mélange d’air et de liquide et par conséquent une très bonne crème fouettée. Pour effectuer un mélange corre ct il vaut toujours mieux partir de la position n°1 et de tourner progressivement le régulateur sur d’autr ...

  • Taylor C004 - C007 - page 23

    FRAN Ç AIS - 10 3. ENTRETIEN Durant les opération d’entretien, ne jamais toucher la machine avec les mains ou avec des outils avant d’avoir vérifié auparavant si la machine est bien en fonction STOP, si l’interrupteur général est bien ouvert et/ou si la fiche de courant multipolaire est bien déconnectée. Au cas où des anomalies dans ...

  • Taylor C004 - C007 - page 24

    11 - FRAN Ç AIS 4. Enlever la tête de distri bution en la tournant dans le sens contraire des aiguilles d’ une montre : a) extraire le robinet de distribution et démonter ses différentes parties (fig.13); b) enlever le tube en le tirant vers l’extérieur et extraire le l abyrinthe de tubes (fig.14); c) enlever la pompe en la tour nant dans ...

  • Taylor C004 - C007 - page 25

    FRAN Ç AIS - 12 4. RECHERCHE DES PANNES PROBLEME CAUSES PROBABLES SOLUTIONS Absence d’alimentation électrique Vérifier la présence de tension sur réseau L’appareil ne fonctionne pas et les voyants sont éteints Interrupteur automatique déclenché ou fusibles du réseau grillés Appeler le technicien Machine non habilitée Appuyer sur la t ...

  • Taylor C004 - C007 - page 26

    ESPAÑOL - 1 ...

  • Taylor C004 - C007 - page 27

    ESPAÑOL - 2 La máquina está cubierta por garantía según las condiciones ilustradas par el vendedor. Por favor escriban en el campo de abajo el número de matrícula de su máquina Número matrícula Timbre del concesionario IMPORTANTE Les recomendamos leer con atención e ín tegramente este manual antes de utiliza r su máquina TAYLOR. En su ...

  • Taylor C004 - C007 - page 28

    ESPAÑOL - 3 Reciba nuestras felicitaciones por haber adquirido una máquina TAYLOR. El siguiente manual, que se fac ilita en dotación con la máquina, ha de considerarse parte integrante y esencial de la mism a y se deberá entregar al usuar io final. Antes de efectuar cualquier operación se recomienda estudiar c on atención las instrucciones c ...

  • Taylor C004 - C007 - page 29

    ESPAÑOL - 4 1 INSTALACIÓN 1.1 Inspección preliminar La máquina viaja bajo responsabilidad del comitent e, si notan daños al embalaje, informen inmediatamente al transportista. Informen igualmente al transportista ensegui da después de la apertura del embalaje, aunque esto ocurra algún día después de la entr ega, si hallaran algún daño a ...

  • Taylor C004 - C007 - page 30

    ESPAÑOL - 5 1.6 Puesta en función En la cuba se halla una confección con los siguientes componentes por ensamblar: tubo, laberinto, grifo, recogedor de gotas. - introducir el tubo en la guía al efecto, hasta encontrar la entrada bomba (f ig.1). Introducir el laberinto en el tubo (fig.2) y introducer el distanciador (solo C007) - montar el grifo ...

  • Taylor C004 - C007 - page 31

    ESPAÑOL - 6 2. FUNCIONAMIENTO 2.1 Panel de control, comandos 1) pulsador general ON/OFF con led que indican: “aparato conectado y bajo t ensión” (led derecho), “máquina habilitada” (led izquierdo); 2) CLEAN: Led “máquina en limpieza”; 3) DISPLAY que indica: cont rol temperatura en cuba – visualización alarmas – tiempo erogació ...

  • Taylor C004 - C007 - page 32

    ESPAÑOL - 7 - Evitar verter nata líquida sobra la bomba, durante el llenado de la cuba - asegurarse de que el azúcar esté bien deshecho en la nata para evitar que eventuales grumos obstruyan el tubo aspirador sumergido de la bomba - añadiduras de azúcar superiores al 8%-10% del peso de la nata líquida están de todas maneras desaconsejados y ...

  • Taylor C004 - C007 - page 33

    ESPAÑOL - 8 2. Presionar contemporàneament e los pulsadores “ON/OF” y “SET”, sobre el diplays apparece la temperatura del termostato. 3. Tener presionado el pulsador “SET” y presionar el pulsador “ON/OFF” para regular la nueva temperatura. 4. Alcanzado el valor deseado, dejar los pulsador es “SET” y “ON/OFF” para memorizar ...

  • Taylor C004 - C007 - page 34

    ESPAÑOL - 9 Sólo actuando sobre el “regulador de nata” es posible obtener la correcta mezcla entre aire y líquido y por lo t anto una óptima nata montada. Para proceder a una correcta regulación es mejor empezar siempre de la posición n°1 y girar progresivamente el regul ador sobre las otras posiciones hasta obtener el producto deseado. ...

  • Taylor C004 - C007 - page 35

    ESPAÑOL - 10 3. MANTENIMIENTO Durante el mantenimiento nunca intervenir con las manos o con herramientas sin haberse asegurado antes de que la máquina esté en f unción de STOP, el interruptor general abierto y/o el enchufe multipol ar de corriente desconectada. En caso se hallaran anomalías en el func ionamiento de la máquina asegurarse de qu ...

  • Taylor C004 - C007 - page 36

    ESPAÑOL - 11 4. quitar la cabeza de erogación girándola en el sentido inverso al de la s agujas del reloj: a) extraer el grifo de er ogación y desmontar sus partes (fig.13); b) quitar el tubo tirándolo hacia el exterior y extraer el laberi nto (fig.14); c) quitar la bomba girándola en el sent ido de las agujas el reloj y extraerla de su sede. ...

  • Taylor C004 - C007 - page 37

    ESPAÑOL - 12 4. BÚSQUEDA DE AVERÍAS INCONVENIENTE PROBABLES CAUSE REMEDIOS Falta de alimentación eléctrica Verificar presencia de tensión en red El aparato no funciona y los testigos están apagados Interruptor automático disparado o fusibles de la red quemados Llamar al técnico Máquina no habilitada Oprimir la tecla general ON/OFF hasta q ...

  • Taylor C004 - C007 - page 38

    1 - ITALIANO ...

  • Taylor C004 - C007 - page 39

    ITALIANO - 2 La macchina e’ coperta da garanzia secondo le condizioni illustrate dal venditore. Per favore scrivete nel campo sottostante il numero di matricola della Vostra macchina Numero matricola Timbro del concessionario IMPORTANTE Vi raccomandiamo di leggere attentament e e interamente questo manuale prima di utilizzare la Vostra macchina T ...

  • Taylor C004 - C007 - page 40

    3 - ITALIANO Ci congratuliamo con Voi per aver scelto di acquistare una macchina TAYLOR. Il seguente manuale, fornito a corredo della macchina, è da c onsiderarsi parte integrante ed essenziale della stessa e dovrà essere consegnato all’utilizzatore finale. Prima di eseguire qualsiasi operazione si raccomanda di studi are attentamente le istruz ...

  • Taylor C004 - C007 - page 41

    ITALIANO - 4 1 INSTALLAZIONE 1.1 Ispezione preliminare La macchina viaggia a rischio e pericolo del committente, se notate danneggiamenti all’imballaggio, fate immediatamente eccezione al vettore. Fate ugualmente eccezione al vettore subito dopo l’apertura dell’imballo, anche se ciò avviene qualche giorno dopo la consegna, se riscontrate qua ...

  • Taylor C004 - C007 - page 42

    5 - ITALIANO 1.6 Messa in funzione In vasca si trova una confezione con i seguenti componenti da assemblare: canotto, tessurizzatore, r ubinetto, raccogli-gocce . - inserire il canotto nell’apposi ta guida, fino ad incontrare l’ingresso pompa (fig.1). Inserire il tessurizzatore nel canotto (fig.2) , inserire il distanziale (solo C007) - montare ...

  • Taylor C004 - C007 - page 43

    ITALIANO - 6 2. FUNZIONAMENTO 2.1 Pannello di controllo,comandi 1. Pulsante generale ON/OFF con led indicanti: “apparecchio allacciato e sotto tensione” (led destro), “macchina abilitata” (led sinistro); 2. CLEAN: Led “macchina in pulizia”; 3. DISPLAY indicante: contro llo temperatura in vasca – visualizzazione allarmi – tempo eroga ...

  • Taylor C004 - C007 - page 44

    7 - ITALIANO - durante il riempimento della vasca evit are di versare panna liquida sulla pompa - assicurarsi che lo zucchero sia ben sciolto nella panna per evitare che eventuali grumi ostruiscano il pescante della pompa - aggiunte di zucchero superiori all’8 %-10% del peso della panna liquida sono comunque sconsigliati poiché limitano l’aume ...

  • Taylor C004 - C007 - page 45

    ITALIANO - 8 2. Premere contempor aneamente i pulsanti ”ON/OFF” e ” SET” , sul display compare il valore di temperatura di termostatatazione. 3. Tenendo premuto il tasto “SET ” premere a impulsi il tasto “ON/OFF” per impostare il nuovo valore di temperatura. 4. Raggiunto il valore desiderato rilasciare i tasti “SET” e “ON/OFF? ...

  • Taylor C004 - C007 - page 46

    9 - ITALIANO Solo agendo sul “regolatore di panna” è possibile o ttenere la corretta miscela aria/liquido e quindi un’ottima panna montata. Per procedere ad una corretta regolazione è sempre preferibile partire dalla posizione n°1 e ruotare progressivamente il regolatore sulle altre posizioni fin quando non si ottiene il prodotto desiderat ...

  • Taylor C004 - C007 - page 47

    ITALIANO - 10 4. MANUTENZIONE Durante la manutenzione non intervenire mai c on le mani o con attrezzi senza essersi prima assicurati che la macchina sia in funz ione di STOP, l’interruttore generale aperto e/o la spina multipolare di corrente scollegata. Qualora si dovessero riscontrare anomalie nel funzionamento della macchina accertarsi che non ...

  • Taylor C004 - C007 - page 48

    11 - ITALIANO 4. Togliere il rubinetto ruot andolo in senso antiorario: a) estrarre il rubinetto di erogazione e scomporlo nelle sue parti (fig. 13); b) togliere il canotto tirandolo verso l’esterno ed estrarre il tessurizzatore (fig.14); c) togliere la pompa ruot andola in senso orario ed estrarla dalla sua sede. Lavare accuratamente. 5. smontar ...

  • Taylor C004 - C007 - page 49

    ITALIANO - 12 4. RICERCA DEI GUASTI INCONVENIENTE PROBABILI CAUSE RIMEDI Mancanza di alimentazione elettrica Verificare presenza di tensione in rete L’apparecchio non funziona e le spie sono spente Interruttore automatico scattato o fusibili della rete bruciati Chiamare il tecnico Macchina non abilitata Premere il tasto generale ON/OFF fin quando ...

  • Taylor C004 - C007 - page 50

    I - ITALIANO 5. APPENDICES / ANNEXES / APENDICES /APPENDICE Machine Specification / Caractéristiqu es techniques / Datos Tecnicos /Dati tecnici C004 Size Net weight Tank capacity Supply voltage Gas Dimensionnement Poids net Capacité du bac Tension d’alimentation Gas Dimensión Peso neto Capacidad del tanque Tension de alimentacion Gas Dimension ...

  • Taylor C004 - C007 - page 51

    ITALIANO - II 5.1 Refrigerant circuit diagram / Schéma du circuit frigorifique / Esquema circuito frigorífico Schema circuito frigorifero APPENDICES ...

  • Taylor C004 - C007 - page 52

    I - ITALIANO NOTES / NOTES / NOTA/ NOTE ...

  • Taylor C004 - C007 - page 53

    ITALIANO - II ...

  • Taylor C004 - C007 - page 54

    TAYLOR COMPANY, 750 North Blackhaw k Boulevard, Rockton, IL 61072 Telephone: (815) 624-8333 Telex: 6871502 TAYLO Fax: (815) 624-8000 www.ta y lor -c omp an y .co m 2005 Taylor All rights reserved cod. M04.38093 ...

Produzent Taylor Kategorie Frozen Dessert Maker

Dokumente, die wir vom Produzenten des Geräts Taylor C004 - C007 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Taylor
- Bedienungsanleitungen C004 - C007
- Produktkarten Taylor
- Informationsbroschüren
- oder Energieetiketten Taylor C004 - C007
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Taylor C004 - C007.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Taylor C004 - C007, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Taylor C004 - C007. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Taylor C004 - C007 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Taylor C004 - C007, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Taylor C004 - C007 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Taylor C004 - C007 verständlich ist.

Eine gänzliche Bedienungsanleitung von Taylor sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Taylor C004 - C007 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Taylor C004 - C007 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Taylor C004 - C007, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Taylor C004 - C007 - die uns die ersten Schritte während der Nutzung von Taylor C004 - C007 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Taylor C004 - C007 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Taylor C004 - C007 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Taylor C004 - C007?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Taylor C004 - C007 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Taylor C004 - C007 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)