-
Chauvet DMX512 - page 1
Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle MinW ash™ USER MANUAL Chauvet, 3000 N 2 9 th Ct, Hollywood, FL 3 3020 U.S.A. (800) 762-1084 – (954 ) 929-1115 FAX (954) 929-5560 www.chauvetlightin g.com ...
-
Chauvet DMX512 - page 2
T ABLE OF C ONTENTS 1. BEFORE YOU BEGIN ............................................................................................................................... .3 W HAT IS INCLUDED ............................................................................................................................... .......... 3 U NPACKING I NSTRUCT ...
-
Chauvet DMX512 - page 3
1. B EFORE Y OU B EGIN What is included ¾ 1 x MinWash™ ¾ Power Cord ¾ Warranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Noti fy the shipper immediately and retain packing materi ...
-
Chauvet DMX512 - page 4
Safety Instructions Please read these instructions carefully, it includes important information about the installation, usage and maintenance of this product. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. • Always make sure that you are conne ...
-
Chauvet DMX512 - page 5
2. I NTRODUCTION Features CONTROL FEATURES • 5 or 13-channel DMX-512 LED moving yoke color wash • Pan: 540 o / tilt: 2 70 o • RGB color mixing • Variable electronic strobe • Variable electronic dimmer (0 – 100%) • Vector speed channel for pan/tilt, RGB color mixing and color m acros • Built-in movement macros v ia master/slave or D ...
-
Chauvet DMX512 - page 6
DMX Channel Summar y 5 Channel Mode C HANNEL F UNCTION 1 Pan 2 Tilt 3 Shutter 4 Color Macro 5 Reserved Product Overview Lens Projector Head CA-9 Controller In p ut LED Readout Voltage Selector Switch DMX Out IEC Power Connection w/ fuse holder DMX In Control Panel MiNWash 6 2007-09-14/09 :44 ...
-
Chauvet DMX512 - page 7
3. S ETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement The fuse is located inside this compartment. Remove using a flat head screwdriver. With a flat head screwdriver wedge the fuse holder out of its housing. Remove the damaged fuse from its holder and replace with exact same type fu ...
-
Chauvet DMX512 - page 8
CABLE CONNECTORS This drawing prov ides a general illustration of the DMX Input/Output panel of a lighting fixture. U X Controller niversal DM Continue t he link Cabling must have a male XLR connector on one end and a female XLR connector on the othe r end. can cause a ground loop, and your fixt ure may perform erratically. Test cables with an ohm ...
-
Chauvet DMX512 - page 9
Often, th and tha initiali settings switch tha ollow may also require a s la ve setting. Please consult the “Operating Instruct ions” sect io n in this manua l for complet e instruc tions for this ty pe of setup and configuration . e setup for Mas ter-Slave Standalone operation requires t the first fi xture in the c hain be zed for this purpose ...
-
Chauvet DMX512 - page 10
4. O PERATING I NSTRUCTIONS Navigating the Control Panel Access control panel functions using the four pa nel buttons located directly underneath the LCD Display. Button Function <MODE/ESC> Used to access the menu or to return to a previous menu option <UP> Scrolls through menu options in ascending order <DOWN> Scrolls through men ...
-
Chauvet DMX512 - page 11
Menu Map MinWash 11 2007-09-14/09 :44 ...
-
Chauvet DMX512 - page 12
User Configurations TO SET THE PAN TO INVERT ING OR NON-INVERT ING: 1) Press the Mode button until it shows or 2) Use the Up/Down buttons to set to the desired inversion, press enter to confirm. TO SET THE TIL T TO INVE RTING OR NON-INVERTING: 1) Press the Mode button until it shows or 2) Use the Up/Down buttons to set to the desired inversion, pre ...
-
Chauvet DMX512 - page 13
Operation Stand-Alone Mode (Auto Mode): This mode allows a single unit to run to a factory installed program in one of two speeds. 1) To set the fixture in auto mode Fast , select . Once confirmed the display reads 2) To set the fixture in auto mode Slow , select Once confirmed the display reads Master/Slave Mode (Master Sound): This mode will allo ...
-
Chauvet DMX512 - page 14
DMX Channel Values (13 Channel) C HA NNE L V ALU E F UNCTION 1 000 Ù 255 Pan 2 000 Ù 255 Pan Fine 3 000 Ù 255 Tilt 4 000 Ù 255 Tilt Fine 5 000 Ù 255 Vector Speed: (Normal → Slow) 6 000 Ù 007 008 Ù 134 135 Ù 239 240 Ù 255 Dimmer/Strobe Closed 100-0% Strobe (slow → fast) Open 7 000 Ù 255 Red 0-100% 8 000 Ù 255 Green 0-100% 9 000 Ù 255 ...
-
Chauvet DMX512 - page 15
DMX Channel Values (5 Channel) C HANNEL V ALU E F UNCTION 1 000 Ù 255 Pan 2 000 Ù 255 Tilt 3 000 Ù 007 008 Ù 134 135 Ù 239 240 Ù 255 Dimmer/Strobe Closed 100-0% Strobe (slow → Fa st) Open 4 000 Ù 007 008 Ù 018 019 Ù 031 032 Ù 043 044 Ù 055 056 Ù 067 068 Ù 079 080 Ù 091 092 Ù 103 104 Ù 115 116 Ù 127 128 Ù 139 140 Ù 151 152 Ù 16 ...
-
Chauvet DMX512 - page 16
SETTING THE STARTING ADDRESS This DMX mode enables the use of a uni versal DMX controller device. Each fixture requires a "sta rt address" from 1 to 512. A fixture requiring one or mo re chan nels for control begins to read the data on the channel indicated by the start address. For example, a fixtur e that uses 6 D MX channels and was ad ...
-
Chauvet DMX512 - page 17
DMX QUICK R EFERENCE CHART DMX Address Quick Reference Chart Dip Switch Position DMX DIP SWITCH SET #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0=OFF #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1=ON #7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X=OFF or ON #6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 #1 #2 #3 #4 #5 0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 1 0 0 ...
-
Chauvet DMX512 - page 18
Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check f an thermal switch reset 9 Beam is very dim or not bright Clean optical system or replace lamp Check 220/110v switch for proper setting 9 Breaker/Fuse keeps blowing Check total load placed on device 9 Chase is too slow Chec ...
-
Chauvet DMX512 - page 19
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A. ) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Pre ss 4) Fax: (954) 929-5560 - (Att ention: Service) Website: http://www.chauvetlighting.com 5. A PPENDIX DMX Primer There are 512 channels in a DMX-512 connection. Channels may be assigned i ...
-
Chauvet DMX512 - page 20
General Maintenanc e To maintain optimum performance and minimize we ar fixtures should be cleaned frequently. Usage and environment are contributing factors in determi ning frequenc y. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output perform ance and can cause overheating. This can lead to re ...
-
Chauvet DMX512 - page 21
Technical Specifica tions WEIGHT & DIMENSIONS Length......................................................................................................................... .... 6.8 in (173 mm) Width .......................................................................................................................... .... 6.8 in (173 mm) H ...
Haben Sie eine Frage bezüglich Chauvet DMX512?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Chauvet DMX512 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Chauvet DMX512 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.