Bedienungsanleitung Hearth and Home Technologies RCT-MLT-II

11 Seiten 0.34 mb
Download

Zur Seite of 11

Summary
  • Hearth and Home Technologies RCT-MLT-II - page 1

    1 Printed in U.S.A. Copyright 2008, Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 100-907F 4/08 RCT -ML T -II Remote Control Kits - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostati- cally or manually from the transmitter . The system oper- ates on rad ...

  • Hearth and Home Technologies RCT-MLT-II - page 2

    2 Figure 1 REMOTE RECEIVER Important: The remote receiver should be positioned close to front in right or left corner where ambient temperatures do not exceed 170º F . The remote receiver is powered by 1 10-120V AC. It plugs into a standard polarized duplex receptacle. Locating Receiver and Operating Functions This remote receiver can be positione ...

  • Hearth and Home Technologies RCT-MLT-II - page 3

    3 Figure 4. Figure 5. VARIABLE REGULATOR GAS CONTROL VALVE FLAME CONTROL SOLENOI D KNOB SCREW NUT VARIABLE REGULATOR JAM NUT VARIABLE REGULATOR SOLENOID WASHER WASHER PLUNGER Installing Flame Control Solenoid 1. Remove the screw and knob from the variable regula- tor and discard. 2. Unscrew the nut from the regulator and discard. 3. Remove the bag ...

  • Hearth and Home Technologies RCT-MLT-II - page 4

    4 The remote receiver has a 3-position slide switch: OFF/ REMOTE/ON (see Figure 6). Figure 6. Remote Receiver TRANSMITTER Important: Before operating remote control, transmit- ter and receiver must have matching security codes. See section ‘Matching Security Codes’. Important: Review ‘Thermo-Updating/Communication- Safety Features’ under ? ...

  • Hearth and Home Technologies RCT-MLT-II - page 5

    5 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer . T o program the remote receiver: 1. Set the slide button on the receiver to the REMOTE position. 2. Push the LEARN button ( ...

  • Hearth and Home Technologies RCT-MLT-II - page 6

    6 Figure 8. Setting Button/Child Proof Lockout Setting ºF/ºC Scale The factory setting for temperature is degrees Fahrenheit ( ºF). T o change this setting to degrees Centigrade (ºC): 1. Remove the battery cover on the back of the transmit- ter and locate the “setting button” at the top center of battery compartment (see Figure 8). 2. Push ...

  • Hearth and Home Technologies RCT-MLT-II - page 7

    7 Adjusting the Flame Height - Operates in ON or THERMO mode This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER. 1. Press and release FLAME button to change fl ame height to HI (see Figure 7, Location #5), (a second fl ame icon appears). 2. Press again to re ...

  • Hearth and Home Technologies RCT-MLT-II - page 8

    8 6. Advance the SET temperature on the transmitter to a temperature of at least 2º F (1º C) above the ROOM temperature displayed on the LCD screen and the system fl ame will ignite. 7. Set the SET temperature to at least 2º F (1º C) below the room temperature and the system fl ame will extin- guish. Thereafter, it should continue to cycle on ...

  • Hearth and Home Technologies RCT-MLT-II - page 9

    9 Figure 9. Intermittent Pilot Ignition (IPI) Wiring Diagram Figure 10. Standing Pilot Ignition Wiring Diagram TRAN SF ORMER 3V A C PLUG I N R E D BA T TERY P ACK THER MO ST A T WIRE AS SEMBL Y JUMPER WIRE (TO BROW N) ORA NG E GREE N VA LV E GR OU ND TO FIR EPLAC E CHA SSIS WHIT E OR A NGE IGNITION MO DULE 3 V AC INTERMITTENT PILOT IGNITOR HOT NEUT ...

  • Hearth and Home Technologies RCT-MLT-II - page 10

    10 Figure 12. Standing Pilot Ignition Wiring Diagram Figure 1 1. Intermittent Pilot Ignition (IPI) Wiring Diagram BLACK S2 ON OFF ON/OFF SWIT CH WHITE T2 RED T1 THERMO PILE GAS V AL UE BLACK S1 3/16” PIGGYBACK CONNECTOR THERMOCOUPLE REMOTE SWITCH PI GT AIL OPTI ONA L W ALL SWI TCH, THERMOST A T OR REMOTE IGN ITION MOD ULE 3V A C TRANSFO RMER 3V A ...

  • Hearth and Home Technologies RCT-MLT-II - page 11

    11 Figure 14. Remote Control Standing Pilot Ignition Wiring Diagram Figure 13. Remote Control Intermittent Pilot Ignition (IPI) Wiring Diagram Remote Control Wiring Diagrams V ALVE GREEN ORANGE JUMPER WIRE (TO BROWN) PLUG IN TRANSFORMER 3 VAC B L A C K R E D GROUND TO FIREPLACE CHASSIS WHITE ORANGE INTERMITTENT PILOT IGNITOR IGNITION MODULE 3 VAC R ...

Produzent Hearth and Home Technologies Kategorie Universal Remote

Dokumente, die wir vom Produzenten des Geräts Hearth and Home Technologies RCT-MLT-II erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Hearth and Home Technologies
- Bedienungsanleitungen RCT-MLT-II
- Produktkarten Hearth and Home Technologies
- Informationsbroschüren
- oder Energieetiketten Hearth and Home Technologies RCT-MLT-II
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Hearth and Home Technologies RCT-MLT-II.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Hearth and Home Technologies RCT-MLT-II, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Hearth and Home Technologies RCT-MLT-II. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Hearth and Home Technologies RCT-MLT-II ansehen.

Die komplette Bedienungsanleitung des Geräts Hearth and Home Technologies RCT-MLT-II, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Hearth and Home Technologies RCT-MLT-II hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Hearth and Home Technologies RCT-MLT-II verständlich ist.

Eine gänzliche Bedienungsanleitung von Hearth and Home Technologies sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Hearth and Home Technologies RCT-MLT-II bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Hearth and Home Technologies RCT-MLT-II befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Hearth and Home Technologies RCT-MLT-II, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Hearth and Home Technologies RCT-MLT-II - die uns die ersten Schritte während der Nutzung von Hearth and Home Technologies RCT-MLT-II erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Hearth and Home Technologies RCT-MLT-II hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Hearth and Home Technologies RCT-MLT-II im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Hearth and Home Technologies RCT-MLT-II?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hearth and Home Technologies RCT-MLT-II nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hearth and Home Technologies RCT-MLT-II hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)