-
Enterasys Networks X009-U - page 1
Enterasys Matrix ™ X S e c u re C o re R o u t e r X4-C Chassis Installation Guide P/N 9034084-02 ...
-
Enterasys Networks X009-U - page 2
...
-
Enterasys Networks X009-U - page 3
i Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this docu ment and its web si te without prior notice. The reader should in all cas es consult Enterasys Netw orks ...
-
Enterasys Networks X009-U - page 4
ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device complie s with Par t 15 of the FCC ru les. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, a ...
-
Enterasys Networks X009-U - page 5
iii Electromagnetic Compatibility (EMC) This product complies with the following: 47 CFR Par t s 2 and 15, CSA C108.8, 89/336/EEC, EN 60825, EN 55022, EN 61000 ‐ 3 ‐ 2, EN 61000 ‐ 3 ‐ 3, EN 55024, AS/NZS CISPR 22, CFR 1040.10, ...
-
Enterasys Networks X009-U - page 6
iv ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 &U ⒈㘨㣃 3%% ⒈Ѡ㣃䝮 3%'( 䞥ሲ䚼ӊ (Metal Parts) hƻ ƻ h ƻ ƻ ⬉䏃ഫ ( Circuit ...
-
Enterasys Networks X009-U - page 7
v VCCI Notice This is a class A product based on the standard of the Vo l u n t a r y Contro l Council for Interfer ence by Information T echnology Equipment (VCCI). If this equipm ent is used in a domest ic environment , radi ...
-
Enterasys Networks X009-U - page 8
vi Declaration of Conformity Application of Co uncil Directiv e(s): 89/336/EEC 73/23/EEC Manufacturer’s Na me: Enterasys Networks, Inc. Manufacturer’ s Address: 50 Minuteman Road Andover, MA USA 01810 European Representative Address: Enterasys Networks, Ltd. Nexus House, Newbury Bu ...
-
Enterasys Networks X009-U - page 9
vii Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZI NG THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“ Agreement”) between the end user (“Y ou”) and Enterasys Networks, Inc. on behalf of itself and ...
-
Enterasys Networks X009-U - page 10
viii 4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agenci es of the U.S. Government, inc luding the U.S. Department of Commerce, which pr ohibit export or di version of certa ...
-
Enterasys Networks X009-U - page 11
ix 10. ENFORCEMENT. You acknowledge and agree that any breach of Se ctions 2, 4, or 9 of this Agreement by You may cau se Enterasys irreparable damage for which recovery of money damages would be inadequate, and that ? ...
-
Enterasys Networks X009-U - page 12
x ...
-
Enterasys Networks X009-U - page 13
xi Contents About This Guide Who Should Use This Guide .............. ................ ............. ................ ................ ................ .......... ...................... xv Using This Guide ................ ................ ............. ................ ................ ................ ................ . ............ ............. ...
-
Enterasys Networks X009-U - page 14
xii Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit ... ...... ................. ................ ......... 3-24 Installing an XFP/SFP Module .. ................... ................ ................ ................ ............. ................ ............. 3-24 Removing an XFP/SFP Module ................... ................ ...
-
Enterasys Networks X009-U - page 15
xiii Figures 1-1 Matrix X4-C Chassis with Redundant Power Supplies . . ................ ................ ............. ................ ........ 1-2 1-2 Matrix X4-C Chassis as Shipped (Rear View) .. ............. ................ ............. ................ ................ ...... .. 1-2 3-1 Disassembly Steps 1 and 2 . ................ ......... ...
-
Enterasys Networks X009-U - page 16
xiv Tables 3-1 DC/AC Power Supply ( PS1-PS3) LED Definitions ........ ................ ................ ............. ................ ...... 3-38 3-2 Fan Tray LED Definitions .......... ................ ............. ................ ................ ................. ............ ............. 3-39 3-3 Control and Fabric Module LED Definitions .. ...
-
Enterasys Networks X009-U - page 17
Matrix X4-C Chassis Installation Guide xv About This Guide This guide describes the Enterasys Matrix™ X4 ‐ C chassis features, options, specificat ions, and provides information to install the chassis in a standard 19 ‐ inch (48.26 ‐ centimeter) equi ...
-
Enterasys Networks X009-U - page 18
Using the Matrix X Router Ma nual Set xvi About This Guide Using the Matrix X Router Manual Set Additional documents are provided to explain installation of X Router Input/Output Modules (IOMs) in the Matrix X4 ‐ C, configuration of CLI commands on the Matr ix ...
-
Enterasys Networks X009-U - page 19
Commonly Used Acronyms Matrix X4-C Chassis Installation Guide xvii Commonly Used Acronyms The following acronyms are used extensiv ely throughout this guide: •I O M – Input/Output Module •F M – Fabric Module •C M – Control Module •L E D – Light Emitting ...
-
Enterasys Networks X009-U - page 20
Getting Help xviii About This Guide ...
-
Enterasys Networks X009-U - page 21
Matrix X4-C Chassis Installation Guide 1-1 1 Overview This chapter describe s the following: System Description The Matrix X4 ‐ C chassis design provides eight slots to seat four Input/Output Modules (IOM), two Fabric Modules (FM), and tw o Control ...
-
Enterasys Networks X009-U - page 22
System Description 1-2 Overview Figure 1-1 Matrix X4-C Chassis with Redundant Power Supplies Figure 1-2 Matrix X4-C C hassis as Shipped (Re ar View) 1 Ground strap receptacle 5 Fabric Module slot (FM1) 2 Fan tray bezel 6 Control Module slot (CM1) 3 IOM coverplate 7 IOM slot 1 4 Fan tray LEDs 8 Power supply vent cover 1 AC power supply inlets (3) wi ...
-
Enterasys Networks X009-U - page 23
Features Matrix X4-C Chassis Installation Guide 1-3 Features The following sections provide an overview of the system features. X4-C Input/Output Modules The Matrix X4 ‐ C chassis supports Input/Output Modules (IOM) which perform all syste m packet forw arding ...
-
Enterasys Networks X009-U - page 24
Features 1-4 Overview supports Access Control Lists (ACLs) and, by default, is associat ed with the VPN Routing/ Forwarding (VRF) instance that all interfaces are assi gned to. Be aw are of the following caveats, howev er , when u ...
-
Enterasys Networks X009-U - page 25
Features Matrix X4-C Chassis Installation Guide 1-5 5. Insert the standby CM into the system and wait until it is fully synchronized with the active CM before removing the activ e CM. Do not physically remove the acti ve CM during ...
-
Enterasys Networks X009-U - page 26
Features 1-6 Overview 7. Again, you can enter the show system high ‐ availability command to veri f y synchronization is complete and the standby CM is up. Note in the output that the Standby Module status has changed from ? ...
-
Enterasys Networks X009-U - page 27
Features Matrix X4-C Chassis Installation Guide 1-7 X4-C Redundant Power Supplies The Matrix X4 ‐ C chassis supports up to three pow er supplies that install on the bottom of the chassis, in slots labeled PS1 through PS3. While the chassis ...
-
Enterasys Networks X009-U - page 28
Features 1-8 Overview Rack-Mount able Chassis The Matrix X4 ‐ C chassis is designed to be mounte d in a standard 19 ‐ inch (48.26 ‐ centimeter) wide equipment rack (six chassis can be loaded into a standard 7 ‐ foot [213.36 ‐ centimeter ...
-
Enterasys Networks X009-U - page 29
Matrix X4-C Chassis Installation Guide 2-1 2 Site and Configuration Guidelines This chapter describe s the following: Site Guidelines The following guidelines must be follow ed when a site is selected for the Matrix X4 ‐ C chassis. If guidelines are not ? ...
-
Enterasys Networks X009-U - page 30
Configuration Guidelines 2-2 Site and Configuration Guidelines Configuration Guidelines The Matrix X4 ‐ C chassis provides eight slots that accept modules. IOM (Input/Output Module) slots are numbered 1 throug h 4 from bottom to top. Tw o Fabric Mo ...
-
Enterasys Networks X009-U - page 31
Matrix X4-C Chassis Installation Guide 3-1 3 Matrix X4-C Chassis Setup This chapter describe s the following: Required T ools Installation equipment needed includes: •B o x cutter • Phillips screwdriver •F l a t blade screwdriver A box cutter is required to cut the sh ...
-
Enterasys Networks X009-U - page 32
Unpacking the Matrix X4-C Chassis 3-2 Matrix X4-C Chassis Setup Unp a cking the Matrix X4-C Chassis The Matrix X4 ‐ C chassis is packed and shipped on a skid. Befo re unpacking the chassis, ex amine the outside packaging for obvious damage. To unpack t ...
-
Enterasys Networks X009-U - page 33
Unpacking the Matrix X4-C Chassis Matrix X4-C Chassis Installation Guide 3-3 Figure 3-2 Disassembly S tep s 3 and 4 5. Open the top of the shipping bag covering the unit, then pull the bag down around the skid, as shown in Figure 3 ‐ 3 . Figure 3-3 Disassembly S t ...
-
Enterasys Networks X009-U - page 34
Unpacking the Matrix X4-C Chassis 3-4 Matrix X4-C Chassis Setup 6. Remove and sav e (for later use) the screws fastening left and right shipping and support brackets to the chassis and the skid. 7. Lift and remove the chassi s from the sk ...
-
Enterasys Networks X009-U - page 35
Setting Up the Matrix X4-C Chassis Matrix X4-C Chassis Installation Guide 3-5 Setting Up the Matrix X4-C Chassis The following sections describe the procedures that must be follow ed to complete chassis installation. Chassis are shipped with all sl ots labeled “1? ...
-
Enterasys Networks X009-U - page 36
Setting Up the Matrix X4-C Chassis 3-6 Matrix X4-C Chassis Setup Inst alling Optional Rack Support Brackets Rack support brackets are shipped with the chassis for additional support underneath the c hassis. They are recommended for installations with fo ur ‐ post ...
-
Enterasys Networks X009-U - page 37
Setting Up the Matrix X4-C Chassis Matrix X4-C Chassis Installation Guide 3-7 Inst alling Optional Mid-Mount Brackets Yo u can purchase an optional mid ‐ mount bracket kit (X4 ‐ MBRKT) for a rack or cabinet when the standard front ‐ chassis ear attachment is u ...
-
Enterasys Networks X009-U - page 38
Setting Up the Matrix X4-C Chassis 3-8 Matrix X4-C Chassis Setup Rack Mounting the Matrix X4-C Chassis To rack ‐ mount the Matrix X4 ‐ C chassis, pr oceed as follows: 1. If you installed the optional mid ‐ mount brackets, skip to Step 3. 2. Lift the chassis on ...
-
Enterasys Networks X009-U - page 39
Setting Up the Matrix X4-C Chassis Matrix X4-C Chassis Installation Guide 3-9 Figure 3-7 Rack Mounting the Mid-Mounted Cha ssis 4. Chassis rack mounting is now complete. Chassis Bonding and Grounding Installing the chassis as described in this chapter meets the protective earth gro ...
-
Enterasys Networks X009-U - page 40
Setting Up the Matrix X4-C Chassis 3-10 Matrix X4-C Chassis Setup Figure 3-8 T elcordia GR-1089 Gr ounding Hole Patt ern and Cable To ground the chassis according to the Te l c o r d i a GR ‐ 1089 Sect ion 9, Bonding and Grounding Requirements, a connection is needed betw ...
-
Enterasys Networks X009-U - page 41
Installing and Removing a Power Supply Matrix X4-C Chassis Installation Guide 3-11 Att aching the Electrost atic Discharge Wrist S trap The Electrostatic Discharge (ESD) wrist strap must be attached be fore handling the power supplies, fan tray , and modules used in the ...
-
Enterasys Networks X009-U - page 42
Installing and Removing a Power Supply 3-12 Matrix X4-C Chassis Setup Power Supply Planning Although each power supply requir es its own circuit, when plan ning the X4 ‐ C pow er budget you have the option of drawing from one or more sources by ...
-
Enterasys Networks X009-U - page 43
Installing and Removing a Power Supply Matrix X4-C Chassis Installation Guide 3-13 Figure 3-12 Removing Power Supply V ent Plate 6. Locate the PS1 power supply slot, as shown in Figure 3 ‐ 12 . 7. Hold the power supply by placing one hand on the handle located on ...
-
Enterasys Networks X009-U - page 44
Installing and Removing a Power Supply 3-14 Matrix X4-C Chassis Setup Figure 3-13 Inst alling Power Supply Module 10. Secure the powe r supply to the chassis by tightening the captive screw . 11. If you are installing additional pow er supplies, remove the coverplates ? ...
-
Enterasys Networks X009-U - page 45
Installing and Removing a Power Supply Matrix X4-C Chassis Installation Guide 3-15 Removing a Power Supply To remove a pow er supply , proceed as follows: 1. Attach the anti ‐ static wrist strap as described in “ Attaching the Elect rostatic Discharge Wr i s t Strap ...
-
Enterasys Networks X009-U - page 46
Installing and Removing a Fan Tray 3-16 Matrix X4-C Chassis Setup Inst alling and Removing a Fan T ray The Matrix X4 ‐ C chassis is equipped with remov able fan trays that allow for easy periodic replacement if a fan fails. To install and remove a ...
-
Enterasys Networks X009-U - page 47
Installing and Removing a Fan Tray Matrix X4-C Chassis Installation Guide 3-17 Figure 3-17 Inst alling Fan T ray 7. Replace the fan tray bezel by li fting it into place and re ‐ attaching the three captive scre ws. Removing a Fan T ray To remove a fan tray , proceed ? ...
-
Enterasys Networks X009-U - page 48
Installing and Removing Modules 3-18 Matrix X4-C Chassis Setup Inst alling and Removing Modules Inst alling and Removing IOMs This section describes the installation of IOMs, and Fabric and Control Modules. Although you can populate any empty slot with its appropria ...
-
Enterasys Networks X009-U - page 49
Installing and Removing Modules Matrix X4-C Chassis Installation Guide 3-19 Figure 3-18 Installing IOMs Figure 3-19 Engaging Ejector Handles 7. T o install additional modules, remov e the coverplates from th e slots, as shown in Figure 3 ‐ 20 , and repeat earlier steps. Save ...
-
Enterasys Networks X009-U - page 50
Installing and Removing Modules 3-20 Matrix X4-C Chassis Setup Figure 3-20 Removing IOM Coverplate 1 IOM slot 2 2 IOM coverplate 3 Captive screws (2) 4 IOM g uide rails FM2 FM1 STATUS TX RX TX RX TX RX TX RX X-M2-00 10G ENET MAC ADD. S/N: S/N: MAC ADD. GROUND STRAP 1 CM2 CM1 4 3 2 1 FAN TRAY Matrix X4 FAN TRAY 2 4 3 4 3 1 ...
-
Enterasys Networks X009-U - page 51
Installing and Removing Modules Matrix X4-C Chassis Installation Guide 3-21 Inst alling and Removing CMs 1. Locate the empty CM1 slot, and position the module in the guide rail at the left of the slot, as shown in Figure 3 ‐ 21 . Gently insert the ...
-
Enterasys Networks X009-U - page 52
Installing and Removing Modules 3-22 Matrix X4-C Chassis Setup Replacing the CM Battery If the P anasonic lithium battery on the CM is failing, the system will operate properly until a power cycle, the n an error message displays (see example, be ...
-
Enterasys Networks X009-U - page 53
Installing and Removing Modules Matrix X4-C Chassis Installation Guide 3-23 Inst alling and Removing FMs 1. Locate the empty FM1 slot and position the module in the guide rail at the left of the slot, as shown in Figure 3 ‐ 22 . Gently insert the ? ...
-
Enterasys Networks X009-U - page 54
Attaching Cables, Installing Compact F lash Card and DIMM Upgrade Kit 3-24 Matrix X4-C Chassis Setup Att aching Cables, Inst alling Comp act Flash Card and DIMM Upgrade Kit Matrix X Router modules provide the following interfaces for cable and Flash card connections: •I O M : XFP or ...
-
Enterasys Networks X009-U - page 55
Attaching Cables, Installing Compac t Flash Car d and DIMM Upgrade Kit Matrix X4-C Chassis Installation Guide 3-25 3. Hold the transceiv er so that the connector will seat properly . 4. Carefully align the transceiver wi th the IOM port slot, as shown in Figure 3 ? ...
-
Enterasys Networks X009-U - page 56
Attaching Cables, Installing Compact F lash Card and DIMM Upgrade Kit 3-26 Matrix X4-C Chassis Setup The procedure below descr ibes how to connect an LC or MT ‐ RJ cable connector to an XFP or SFP port connector , respectively . 1. Remove the protectiv e c ...
-
Enterasys Networks X009-U - page 57
Attaching Cables, Installing Compac t Flash Car d and DIMM Upgrade Kit Matrix X4-C Chassis Installation Guide 3-27 5. After the chassis has been powered up, ver if y a link exists by checking that the port RX LED is on (f lashing amber , blinking green, ...
-
Enterasys Networks X009-U - page 58
Attaching Cables, Installing Compact F lash Card and DIMM Upgrade Kit 3-28 Matrix X4-C Chassis Setup Figure 3-25 Connecting an IBM PC or Comp atible Connecting the CM COM Port to a VT Series T erminal To connect a VT Series terminal to the CM COM port ( Figure 3 ‐ 26 ), use a UTP cable ? ...
-
Enterasys Networks X009-U - page 59
Attaching Cables, Installing Compac t Flash Car d and DIMM Upgrade Kit Matrix X4-C Chassis Installation Guide 3-29 Figure 3-26 Connecting a VT Series T erminal Connecting the CM CO M Port to a Modem To connect a modem to the CM COM port ( Figure 3 ‐ 27 ), use a UTP cable with RJ45 co ...
-
Enterasys Networks X009-U - page 60
Attaching Cables, Installing Compact F lash Card and DIMM Upgrade Kit 3-30 Matrix X4-C Chassis Setup Figure 3-27 Connecting to a Modem Adapter Wiring and Signal Assignment s 1 UTP cable with R J45 connectors 4 Local modem 2 RJ45 COM port 5 Remote modem 3 RJ45-to-DB25 modem adapter 6 IBM PC or compatible device STA TUS ACTIVE/ STANDBY RESET USB ETHE ...
-
Enterasys Networks X009-U - page 61
Attaching Cables, Installing Compac t Flash Car d and DIMM Upgrade Kit Matrix X4-C Chassis Installation Guide 3-31 Connecting to the CM USB Port The X4 ‐ C supports fast and easy configuration downloads using the CM USB port. Using eith er a USB storage device (as sho ...
-
Enterasys Networks X009-U - page 62
Attaching Cables, Installing Compact F lash Card and DIMM Upgrade Kit 3-32 Matrix X4-C Chassis Setup Figure 3-28 Att aching a USB Device to the CM Inst alling a Comp act Flash Card The Control Module provides an IDE port housing a 1 GB Flash memo ry card, as shown in Figure 3 ‐ 2 ...
-
Enterasys Networks X009-U - page 63
Attaching Cables, Installing Compac t Flash Car d and DIMM Upgrade Kit Matrix X4-C Chassis Installation Guide 3-33 Inst alling the Memory Upgrade Kit The following sections describe how to upgrade the Dual In ‐ line Memory Modules (DIMMs) on the X ‐ CM ‐ 00 Control Module ...
-
Enterasys Networks X009-U - page 64
Attaching Cables, Installing Compact F lash Card and DIMM Upgrade Kit 3-34 Matrix X4-C Chassis Setup Figure 3-31 Removing the Existing DIMM 5. Repeat step 4 to remov e the second DIMM. Inst alling the DIMMs To install the DIMMs and proceed as follows: 1. Make sure connector arm ...
-
Enterasys Networks X009-U - page 65
Optional Cable Management Kit Matrix X4-C Chassis Installation Guide 3-35 Optional Cable Management Kit Cables can be kept neat and secure using the optional Cable Management Kit (X4 ‐ CBLMG ‐ KIT). Using the Cable Management Kit ensures that cables are ...
-
Enterasys Networks X009-U - page 66
Optional Cable Management Kit 3-36 Matrix X4-C Chassis Setup Figure 3-32 Inst alling the Cable Manageme nt Assembly 4. Remove the bar from the cable management assembly by loosening the two (2) captive screws on the bar . See Figure 3 ‐ 33 , below . 5. Gather the ...
-
Enterasys Networks X009-U - page 67
Powering Up the Matrix X4-C Chassis Matrix X4-C Chassis Installation Guide 3-37 6. Reattach the bar to the cable management assembly by tightening the tw o (2) captive screws on the bar . 7. If you wish to remove a cable strap, simpl y unscrew ? ...
-
Enterasys Networks X009-U - page 68
LEDs and Reset Button 3-38 Matrix X4-C Chassis Setup Power Supply LEDs Tw o LEDs are provided on the power supply module: a DC LED indicati ng the operational status of outgoing power and an AC LED indicating incoming AC line v oltage is ...
-
Enterasys Networks X009-U - page 69
LEDs and Reset Button Matrix X4-C Chassis Installation Guide 3-39 Fan T ray LED Each fan tray provides a status LED on its front panel. Fan tray LEDs are al so included on the cable management base pan el. Refer to Figure 3 ‐ 36 and Figure ...
-
Enterasys Networks X009-U - page 70
LEDs and Reset Button 3-40 Matrix X4-C Chassis Setup The following additional conditions apply: •A f t e r powe r up, the fan tray LED remains red until diagnostics begin, then wil l blink green. When blinking amber , the fan controller will ? ...
-
Enterasys Networks X009-U - page 71
LEDs and Reset Button Matrix X4-C Chassis Installation Guide 3-41 T able 3-3 Control and Fabric Module LED Definitions The following additional conditions apply: •A f t e r modul e power up, the CM/FM ST A TUS LED will remain red until diagnostics begin then will blin ...
-
Enterasys Networks X009-U - page 72
First-Time Quick Configuration 3-42 Matrix X4-C Chassis Setup The following additional conditions apply: •A f t e r IOM power up, the ST A TUS LED will remain red until diagnostics begin then will blink green. First-T ime Quick Configuration This section descr ...
-
Enterasys Networks X009-U - page 73
First-Time Quick Configuration Matrix X4-C Chassis Installation Guide 3-43 Assigning an IP Address to eth0 To assign an IP address to the Mat rix X4 ‐ C’ s management interface (eth0), enter the following commands at the CLI prompt: 1. matrix-x(switch-su) router 2. matr ...
-
Enterasys Networks X009-U - page 74
First-Time Quick Configuration 3-44 Matrix X4-C Chassis Setup ...
-
Enterasys Networks X009-U - page 75
Matrix X4-C Chassis Installation Guide A-1 A Specifications and Re gulatory Compliance This appendix provides information about the foll owing: Enterasys Networks reserves the right to change the specifications at any time without notice. Chassis, Power Supply , and Fan T ray S ...
-
Enterasys Networks X009-U - page 76
Power Supply Requirements, Spec ifications, and Tw ist Lock Options A-2 Specifications and Regulatory Compliance P o w e r Supply Requirement s, Speci fic ations, and T wist Lock Options The requirements for Matri x X Router AC po wer supply modules are as follows: The power specif ications ? ...
-
Enterasys Networks X009-U - page 77
10-Gigabit Ethernet Transceiver Specifications (XFP) Matrix X4-C Chassis Installation Guide A-3 Matrix X4 ‐ C twist lock powe r cord options are as follo ws: 10-Gigabit Ethernet T ranscei ver Specifications (XFP) The 10 ‐ Gigabit XFP (10 ‐ Gigabit Small Form Factor Pluggable) ...
-
Enterasys Networks X009-U - page 78
1-Gigabit Ethernet Transceiv er Specifications (SFP) A-4 Specifications and Regulatory Compliance Ta b l e A ‐ 8 provides the input/output specifications for each XFP ver sio n as specif ied in the IEEE 802.3ae ‐ 2002 standard. The following XFP specifications in Ta ...
-
Enterasys Networks X009-U - page 79
SFP Input/Output Specifications Matrix X4-C Chassis Installation Guide A-5 SFP Input/Output Sp ecifications Matrix X Router Ethernet port interfaces accept 1000BA SE ‐ SX short wav e l e n g t h or 1000BASE ‐ LX long wave l e ng th fiber SFPs (see Ta b l e A ‐ 10 ) and ? ...
-
Enterasys Networks X009-U - page 80
SFP Input/Output Specifications A-6 Specifications and Regulatory Compliance MGBIC-LC03 S pecific ations (1000BASE-SX) MGBIC-LC09 S pecific ations (1000BASE-LX) T able A-13 MG BIC-LC03 Optical Specifications Item 62.5/125 µm MMF 50/125 µm MM F T ransmit Power (minimu m) -9.5 dBm -9.5 dBm T ransmit Power (maximum) -3 dBm -3 dBm Receive Sensitivity ...
-
Enterasys Networks X009-U - page 81
SFP Input/Output Specifications Matrix X4-C Chassis Installation Guide A-7 MGBIC-08 Specifications (1000BASE-ELX) MGBIC-02 Specifications (1000BASE-T) T able A-17 MGBIC-08 Optical Specifications Item 10 µm SMF T ransmit Power (minimum) -0 dBm, min. +2 dBm, typical +5 dBm, max. Receive Sensitivity -24 dBm, min. -26 dBm, typical Maximum Input Power ...
-
Enterasys Networks X009-U - page 82
COM Port Pinout Assignments A-8 Specifications and Regulatory Compliance COM Port Pinout Assignment s The COM port is a serial communications port for local access to local management, as shown in Figure A ‐ 1 . Refer to Ta b l e A ‐ 20 for the COM p ...
-
Enterasys Networks X009-U - page 83
Index-1 Index Numerics 10-Gigabit Ethernet Transceiv er Specifications (XFP) A-3 1-Gigabit Ethernet T ransceiver Specifications (SFP) A-4 A AC Power LED description of 3-38 location on power supply 3-38 AC1 inlet link to PS1 3-15 view of 3-15 , 3-37 ACTIVE/STANDBY LED description of 3-41 for CM and FM 3-40 indication for 3-41 Assigning an IP Addres ...
-
Enterasys Networks X009-U - page 84
Index-2 Fan Tray bezel removal for fan tray installation 3-16 FCC Notice ii Fiber budget A-5 Firmware License Ag reement vii First-time quick configuration 3-42 to 3-43 FM1 slot view of 3-23 without coverplate 3-23 G Getting he lp Contract number for xvii information for xvii RMA number xvii serial, revision numbers xvii H Hazardous Substances iii ...
-
Enterasys Networks X009-U - page 85
Index-3 FCC ii General ii Industry Canada ii Product Safety ii VCCI v NTP enabling of 3-43 P Performing cable management description of 3-35 Power A-2 Power supply description of 3-1 1 description of air flow 1-7 description of LEDs 3-38 installation of 3-12 location of vent plate 3-13 planning for 3-12 removal of 3-15 twist lock power cord 1-7 twi ...
-
Enterasys Networks X009-U - page 86
Index-4 ...
Haben Sie eine Frage bezüglich Enterasys Networks X009-U?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Enterasys Networks X009-U nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Enterasys Networks X009-U hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.