Bedienungsanleitung Roland VH-12

12 Seiten 0.81 mb
Download

Zur Seite of 12

Summary
  • Roland VH-12 - page 1

    03458434 ’05-10-6N Owner’s Manual The VH-12 V-Hi-Hat is to be used in combination with the Roland TD-20 or TD-12 Percussion Sound Module. fig.Structure * Hi-hat stand is not included. For details on compatible stands, refer to p. 10. 202 Copyright © 2004 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in a ...

  • Roland VH-12 - page 2

    2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002a • Do not open or perform any internal modifications on the unit. ......................................................... ...

  • Roland VH-12 - page 3

    3 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can def ...

  • Roland VH-12 - page 4

    4 Getting Started Similar Touch and Feel as with an Acoustic Hi-Hat The superior design has taken into account not only the shape of the hi-hat, but also the bounce of the stick, and even the movement caused by playing, making it possible to play with the same feel as an acoustic hi-hat. Smooth Transition Between Closed and Open Tones When you stri ...

  • Roland VH-12 - page 5

    5 Mounting on the Hi-Hat Stand * Due to the different shape, the clutch included with the hi-hat stand cannot be used with the VH-12. Be sure to use the special VH-12 clutch. fig.Clutch.e 1. Use the tuning key included with the VH-12 to loosen the clutch bolt, then simultaneously turn and remove the clutch top. fig.Clutch-2.e 2. Remove the two lock ...

  • Roland VH-12 - page 6

    6 Mounting on the Hi-Hat Stand 1. Remove the clutch included with the hi-hat stand from the cymbal rod. * The clutch included with the hi-hat stand will not be used. * It is not necessary to remove the felt (or rubber) pad on the hi- hat stand used for supporting the bottom cymbal. 2. Confirm that the cymbal rod is firmly secured. For instructions ...

  • Roland VH-12 - page 7

    7 Mounting on the Hi-Hat Stand 6. Attach the clamp and holder to the pipe on the upper part of the hi-hat stand, then slightly tighten the assembly with the tuning key. fig.Bottom-03.e 7. Pass the ends of the holder through the grooves in the metal portion of the bottom hi- hat, then while strongly pulling the clamp downward, secure it with the tun ...

  • Roland VH-12 - page 8

    8 Mounting on the Hi-Hat Stand 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 1. Connect the VH-12’s TRIGGER OUTPUT jack to the sound module’s TRIGGER INPUT HI-HAT jack, and the VH-12’s CONTROL OUTPUT jack to the sound m ...

  • Roland VH-12 - page 9

    9 Mounting on the Hi-Hat Stand 1. Adjust the gap between the top hi-hat and bottom hi-hat to a clearance of approximately 10 mm, then tighten the clutch screw. fig.Gap.e * Although the gap can be adjusted to a clearance that makes playing the hi-hat easier, setting too narrow or wide a gap can cause improper function of the unit and prevent the hi- ...

  • Roland VH-12 - page 10

    10 Playing Methods The hi-hat tone changes smoothly and continuously from open to closed in response to how far the pedal is pressed. You can also play the foot closed sound (playing the hi-hat with the pedal completely pressed down) and foot splash sound (playing the hi-hat with the pedal fully pressed and then instantly opening it). When you stri ...

  • Roland VH-12 - page 11

    11 Troubleshooting Was the unit adjusted after being connected to the sound module? When using the VH-12, be sure to run the automatic offset adjustment on your sound module (p. 8). Is the TRIGGER OUTPUT connected to the sound module’s HH CTRL jack? Connect the VH-12’s TRIGGER OUTPUT jack to the sound module’s HI-HAT jack, and the CONTROL OUT ...

  • Roland VH-12 - page 12

    As of August 1, 2005 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 ...

Produzent Roland Kategorie Musical Instrument

Dokumente, die wir vom Produzenten des Geräts Roland VH-12 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Roland
- Bedienungsanleitungen VH-12
- Produktkarten Roland
- Informationsbroschüren
- oder Energieetiketten Roland VH-12
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Roland VH-12.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Roland VH-12, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Roland VH-12. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Roland VH-12 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Roland VH-12, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Roland VH-12 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Roland VH-12 verständlich ist.

Eine gänzliche Bedienungsanleitung von Roland sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Roland VH-12 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Roland VH-12 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Roland VH-12, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Roland VH-12 - die uns die ersten Schritte während der Nutzung von Roland VH-12 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Roland VH-12 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Roland VH-12 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Roland VH-12?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Roland VH-12 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Roland VH-12 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)