Bedienungsanleitung Western Telematic RMM-288

21 Seiten 0.13 mb
Download

Zur Seite of 21

Summary
  • Western Telematic RMM-288 - page 1

    WTI Part No.: 12548 Rev. F RMM Rack Mount Data/Fax Modem User's Guide 5 Sterling, Irvine, California 92618-2517 U.S. and Canada: 1-800-854-7226 Phone: (949) 586-9950 Fax: (949) 583-9514 http://www.wti.com Table of Contents 1. Introduction ● 2. Unit Description 2.1. Front Panel Indicators ❍ ● 3. Operation ● 4. Installation 4.1. 48 Volt ...

  • Western Telematic RMM-288 - page 2

    6. S-Registers ● 7. Specifications ● 8. Customer Service ● List of Figures 1. Front Panel ● 2. The Status Screen (Defaults Shown) ● 3. 48 Volt DC Power Option ● 1. Introduction The RMM Rack Mount Data/Fax Modem is designed for applications that require a single "Industrial Strength" modem that easily installs in equipment bays ...

  • Western Telematic RMM-288 - page 3

    AA (Auto Answer) On Answer mode only: Modem is answering a call and DIP Switch 5 is UP (Enable Auto Answer), or register S0 is set to 1 (Auto Answer, 1 Ring). Off No activity, or modem is originating a call. Flash Incoming call. CD (Carrier Detect) On A valid data carrier signal has been received from a remote modem, and Dip Switch 6 is UP (Normal ...

  • Western Telematic RMM-288 - page 4

    B0 E1 F1 M1 Q0 V1 X1 Y0 BAUD=9600 PARITY=N WORDLEN=8 DIAL=PULSE ON HOOK &A1 &B0 &C1 &D2 &G0 &H0 &I0 &K1 &M4 &N0 &P0 &R1 &S0 &T5 &Y1 S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002 S07=060 S08=002 S09=006 S10=007 S11=070 S12=050 S13=000 S14=000 S15=000 S16=000 S17=000 S18=000 S19=00 ...

  • Western Telematic RMM-288 - page 5

    4.2. Dip Switch Settings Switch Factory Setting Function 1 Data Terminal Ready (DTR) Override X UP Normal DTR operations: Computer must provide DTR signal for modem to accept commands. Dropping DTR terminates call. DOWN DTR Override: Modem ignores DTR 2 Verbal/Numeric Result Codes X UP Verbal (Word) Results DOWN Numeric Results 3 Result Code Displa ...

  • Western Telematic RMM-288 - page 6

    UP Dumb Mode: Disables command recognition X DOWN Smart Mode: Enables command recognition 5. Command Summary Type commands in either upper or lower case. Do not use a combination of upper and lower case characters. ● Use the Backspace key to delete errors. Note that the original AT command is stored in the modem buffer, and cannot be deleted. ● ...

  • Western Telematic RMM-288 - page 7

    * DP Pulse (Rotary) Dial Mode DR Originates call using answer (reverse) frequencies. DS n Dials phone number string stored in NVRAM at position n ( n = 0-3). Phone numbers are stored with the &Z n = s command. DT Tone Dial Mode D, (Comma) Two Second Pause. Comma pause duration can be redefined via the S8 Register. D; (Semicolon) Return to Comma ...

  • Western Telematic RMM-288 - page 8

    I5 Nonvolatile memory (NVRAM) settings I6 Link diagnostics I7 Product configuration M n Operates Speaker M0 Speaker always Off. * M1 Speaker On until connect. M2 Speaker always On. M3 Speaker On after dial, until connect. O n Returns online O0 Returns online. * O1 Returns online and retrains. P Sets pulse dial (for phone lines that don't suppo ...

  • Western Telematic RMM-288 - page 9

    1/CONNECT XXXXX 2/RING XXXXX 3/NO CARRIER XXXXX 4/ERROR XXXXX 5/CONNECT 1200 X X X X 6/NO DIAL TONE X X 7/BUSY X X 8/NO ANSWER* X X 10/CONNECT 2400 X X X X 13/CONNECT 9600 X X X X 18/CONNECT 4800 X X X X 20/CONNECT 7200 X X X X 21/CONNECT 12000 X X X X 25/CONNECT 14400 X X X X 43/CONNECT 16800 X X X X 85/CONNECT 19200 X X X X 91/CONNECT 21600 X X X ...

  • Western Telematic RMM-288 - page 10

    Command Function/Options Y n Selects Power-on/Reset default configuration. * Y0 Default is profile 0 setting in NVRAM. Y1 Default is profile 1 setting in NVRAM. Z n Resets modem based on current DIP Switch settings. Z0 Resets modem to NVRAM profile selected by the Y command. Z1 Resets modem to NVRAM profile 0. Z2 Resets modem to NVRAM profile 1. Z3 ...

  • Western Telematic RMM-288 - page 11

    * &D2 Normal DTR operations &D3 Resets on receipt of DTR &F n Loads a read-only (non-programmable) factory configuration. &F0 Generic Template * &F1 Hardware flow control template &F2 Software flow control template &G n Sets Guard Tone * &G0 No guard tone (U.S.A. and Canada). &G1 550 Hz guard tone (some European ...

  • Western Telematic RMM-288 - page 12

    &M5 ARQ mode &N n Sets connect speed. If connection cannot be established at this speed, the modem will hang up. Sets ceiling connect speed if &U n is greater than 0 (See &U n ). * &N0 Variable Rate &N1 300 bps &N2 1200 bps &N3 2400 bps &N4 4800 bps &N5 7200 bps &N6 9600 bps &N7 12,000 bps &N8 14, ...

  • Western Telematic RMM-288 - page 13

    &S1 Modem controls DSR &T n Begins test modes &T0 Ends test in progress &T1 Analog Loopback &T2 Reserved &T3 Local Digital Loopback &T4 Enables Remote Digital Loopback * &T5 Prohibits Remote Digital Loopback &T6 Initiates Remote Digital Loopback &T7 Remote Digital with self test and error detector &T8 Ana ...

  • Western Telematic RMM-288 - page 14

    &W0 Modifies the NVRAM 0 template (Y0). &W1 Modifies the NVRAM 1 template (Y1). &Y n Sets break handling &Y0 Destructive, but doesn't send break. * &Y1 Destructive, expedited &Y2 Non-destructive, expedited &Z n = s Writes phone number s to NVRAM at position n ( n = 0 - 3). &Z n =L Writes the last executed dial s ...

  • Western Telematic RMM-288 - page 15

    S6 2 Sets the number of seconds the modem will wait before dialing. If X n is set to X2 or X4, S6 determines the timeout length when no dial tone is detected. S7 60 Sets the number of seconds the modem will wait for a carrier. Often used to select a longer duration when the modem is originating an international connection. S8 2 Sets the duration (i ...

  • Western Telematic RMM-288 - page 16

    5 32 Reserved 6 64 Reserved 7 128 Disconnect on escape code. * The 1.5K-byte non-ARQ buffer allows data transfer with Xmodem and Ymodem type file transfer protocols without using flow control. The 128 Byte option allows remote users with slower modems to prevent transmitted data from scrolling off screen. When a remote user sends an XOFF (Ctrl-S) t ...

  • Western Telematic RMM-288 - page 17

    S18 0 Test timer for &Tn loopback testing. Sets the length of time (in seconds) the modem will wait before automatically timing out and terminating the test. When set to 0, the timer is disabled. Valid range is 1 - 255. S19 0 Sets the duration (in minutes) for the Inactivity Timer. The timer activates when there is no data activity on the phone ...

  • Western Telematic RMM-288 - page 18

    7 128 Software compatibility code. This setting disables the codes and displays the 9600 code instead. The actual rate of the call can be viewed on the ATI6 screen. Used for unusual software incompatibilities. Some software may not accept 7200, 12000 and 14400 bps or greater result codes. S28 0 Eliminates the V.32 answer tones for a faster connecti ...

  • Western Telematic RMM-288 - page 19

    S34 0 Bit-mapped register setup for 28.8 modems only. To set registers, see instructions for S13. Bit Value Result 0 1 Disable 8S-2D trellis encoding. 1 2 Disable 16S-4D trellis encoding. 2 4 Disable 32S-2D trellis encoding. 3 8 Disable 64S-4D trellis encoding. 4 16 Disable nonlinear coding. 5 32 Disable TX level deviation. 6 64 Disable Pre-emphasi ...

  • Western Telematic RMM-288 - page 20

    Status/Help: Status display shows current settings and stored numbers. A Help display summarizes the command set and S-Register functions. FCC Reg. No.: CJEUSA-24375-M5-E Ringer Equivalence: 0.9 B Compliance: FCC Part 68 / Part 15 Class B Temperature: 0 degrees to 50 degrees C (operating) Power: AC Model: 115/230 VAC, 50/60 Hz, 10 Watts (switchable ...

  • Western Telematic RMM-288 - page 21

    © Copyright Western Telematic, Inc. 1998 Printed in the United States of America January 2000 Part Number: 12548 Revision: F RMM Rack Mount Modem; User's Guide file:///C|/WEBPAGE/guides/rmm/rmm_manl.htm (21 of 21) [2/7/2000 10:55:45 AM] ...

Produzent Western Telematic Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Western Telematic RMM-288 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Western Telematic
- Bedienungsanleitungen RMM-288
- Produktkarten Western Telematic
- Informationsbroschüren
- oder Energieetiketten Western Telematic RMM-288
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Western Telematic RMM-288.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Western Telematic RMM-288, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Western Telematic RMM-288. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Western Telematic RMM-288 ansehen.

Die komplette Bedienungsanleitung des Geräts Western Telematic RMM-288, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Western Telematic RMM-288 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Western Telematic RMM-288 verständlich ist.

Eine gänzliche Bedienungsanleitung von Western Telematic sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Western Telematic RMM-288 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Western Telematic RMM-288 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Western Telematic RMM-288, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Western Telematic RMM-288 - die uns die ersten Schritte während der Nutzung von Western Telematic RMM-288 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Western Telematic RMM-288 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Western Telematic RMM-288 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Western Telematic RMM-288?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Western Telematic RMM-288 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Western Telematic RMM-288 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)