-
Craftsman 315.1191 - page 1
PERATOR'S MANUAL ® 19.2 VOLT 2-SPEED Model No. 315.119100 1/2 in. DRILL-DRIVER _IL WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web pag ...
-
Craftsman 315.1191 - page 2
[] Warranty .......................................................................................................................................................................... 2 [] Introduction ..................................................................................................................................................... ...
-
Craftsman 315.1191 - page 3
A WARNING = Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS WORK AREA SAFETY [] Keep ...
-
Craftsman 315.1191 - page 4
operation, if damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. [] Keep cutting tools sharp and clean. Properly main- tained cutting tools with sharp cutting edges are less likely to bind and are easier to control. [] Use the power tool, accessories and tool bits etc., in accordance with t ...
-
Craftsman 315.1191 - page 5
Some ofthe following symbols may be used on this product. Please study them and learn their meaning. Proper inter- pretation of these symbols will allow you to operate the product better andsafer. SYMBOL V A mz W min n o [] .../min J @ 0 A & ® NAME Volts Amperes Hertz Watt Minutes Alternating Current Direct Current No Load Speed Class II Tool ...
-
Craftsman 315.1191 - page 6
The following signal words andmeanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could WARNING: result in death o ...
-
Craftsman 315.1191 - page 7
PRODUCT SPECiFICATiONS Coupler ......................................................... 1/2 in. Keyless Motor ............................................................... 19.2 Volt DC Switch .............................. VSR (Variable Speed Reversible) No Load Speed ....................... 0-440/0-1,600 r/min. (RPM) Clutch .................... ...
-
Craftsman 315.1191 - page 8
KNOW YOUR DRILL=DRIVER See Figure 1. The safe use of this product requires an understanding of the information on the tool and in this operator's manual as well as a knowledge of the project you are attempt- ing. Before use of this product, familiarize yourself with all operating features and safety rules. BIT STORAGE Bits provided with the dr ...
-
Craftsman 315.1191 - page 9
A WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. A WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible seriou ...
-
Craftsman 315.1191 - page 10
SWITCH TRIGGER See Figure 3. To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. VARIABLE SPEED The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with de- creased trigger pressure. NOTE: You might hear a whistling or ringing noise from the switch during ...
-
Craftsman 315.1191 - page 11
TWO-SPEED GEAR TRAIN (HI-LO) See Figure 5. The drill has a two-speed gear train designed for drilling or driving at LO (1} or HI (2} speeds. A slide switch is located on top of the drill to select either LO (1} or HI (2} speed. When using drill in the LO (1} speed range, speed will decrease and unit will have more power and torque. When using drill ...
-
Craftsman 315.1191 - page 12
BiT STORAGE See Figure 7. When not in use, bits provided with the drill can be placed in the storage area located on the base of the drill. iNSTALLING BITS See Figures 8 - 9. [] Lock the switch trigger by placing the direction of rotation selector in the center position. [] Open or close the chuck jaws to a point where the opening is slightly large ...
-
Craftsman 315.1191 - page 13
DRILLING See Figure 10, A level is located on the top of the motor housing to help keep the drill bit level during use. [] Check the direction of rotation selector for the correct setting (forward or reverse). [] Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates. [] Hold the drill firmly and ...
-
Craftsman 315.1191 - page 14
BATTERY GAUGE See Figure 11. [] To display the amount of charge left in the battery, press and hold the battery gauge button. [] If the battery gauge indicator light glows green, the battery pack is fully charged. [] If it glows yellow, it has a usable charge remaining but will soon require recharging. [] If it glows red, the battery requires recha ...
-
Craftsman 315.1191 - page 15
CHUCK REMOVAL See Figures 13- 15, The chuck may be removed and replaced by a new one. [] Lock the switch trigger by placing the direction of rota- tion selector in center position. [] Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. [] Tap the hex key sharply with a mallet in a clockwise direction ...
-
Craftsman 315.1191 - page 16
A A A WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields when using compressed air to clean tools. If the operation is dusty, also wear a dust mask. WARNING: To avoid serious personal injur ...
-
Craftsman 315.1191 - page 17
[ CRAFTSMAN 19.2 VOLT DRILL-DRIVER- MODEL NUMBER 315.119100 The model number will be found on a plate attached to the motor housing, Always mention the model ] number in all correspondence regarding your DRILL-DRIVER or when ordering repair parts. ] SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 1 6 5 Key Part No. Number 1 6613402 2 690033096 3 94 ...
-
Craftsman 315.1191 - page 18
Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For ...
Haben Sie eine Frage bezüglich Craftsman 315.1191?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Craftsman 315.1191 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Craftsman 315.1191 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.