Deutsch dropdown-ico

Bedienungsanleitung Socket Mobile Ethernet Blaster Communications Cable

32 Seiten 0.64 mb
Download

Zur Seite of 32

Summary
  • Socket Mobile Ethernet Blaster Communications Cable - page 1

    101 Innovatio n Drive San Jose, CA 95134 (408) 544- 7000 http: //www .al tera. com EthernetBlaster Communications Cable User Guide UG-120904-1.0 P25-10326-00 Document Version: 1.0 Document Date: December 2004 ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 2

    Copyright © 2004 Altera Corporation. All righ ts reserved. Altera, The Programmable Solu tions Company, the stylized Altera logo, specific device des- ignations, and all other words and logos that are identified as tr ademarks and/or service marks ar e, unless noted otherwis e, th e trademarks and service mark s of Altera Corporation in the U.S. a ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 3

    Altera Corporation iii Contents Chapter 1. About th e EthernetBlaster Co mmunications Cab le Introduction ..... ........... ........... ......... ........... ........... ......... ........... ........... ............ ........ ...... ...... ........... ........ 1–1 Supported Devices .......... ......... ........... ........... ........... ........ ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 4

    iv Altera Corporation EthernetBlaster Communications Cable User Guide Contents ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 5

    Altera Corporation 1–1 December 2004 Chapter 1. About the EthernetBlaster Comm unications Cab le Introduction The Etherne tBlaster comm unications cable connects to a standar d Ethernet network port with an RJ-4 5 connector . This cable communic ates with client systems using the TCP/IP protocol and supports both static and dynamic IP addressing. ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 6

    1–2 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Introduction Power Requirements The EthernetBl aster communic ations cable r equir es between 1.5 V and 5.0 V from the tar get circuit boar d, and 12.0 VDC (0.875A) input power for the EthernetBlaster V CCSUPPL Y (a 12.0 VDC wall transformer is supplied). The Eth ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 7

    Altera Corporation 1–3 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble jack. The target port side includes the 10-pin female target port and LED status light. The base of the cabl e includes the MAC address and host name. Figure 1–1 shows the side and base views of the hard ware. Fig ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 8

    1–4 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup Static & Dynamic IP Addressing The EthernetBl aster communic ations cable support s both static IP and dynamic IP addressing, the latter by means of Dynamic Host Configuration Pr otocol (DHCP). By defa ult, the EthernetBlas ter cable is configured ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 9

    Altera Corporation 1–5 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble 1 For plug and header dimensio ns, pin names, and operating conditions, see Chapter 3, “E thernetBlaster Communications Cable Specifications.” Remote Connection via Network Using Default Factory Settings Use the ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 10

    1–6 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup Figure 1–3. Connecting the EthernetBlaster Communica tions Cable to the T arget Circuit Board 4. Plug the supplied 12.0 VDC wall transformer into a power outlet and then into the EthernetBl aster communications cable. 1 Always connect the network pa ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 11

    Altera Corporation 1–7 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble Figure 1–4. MAC Address & Host Name Browse to http://< host name > and specify the host name from the label on the base of your Ethernet Blaster communications cable. The EthernetBlaster login window op ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 12

    1–8 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup 1 T o maintain your computer ’s IP address and change the EthernetBlaster c ommunications cable default IP addr ess, see “Configuring the Ethernet Blaster Hardwar e to Use Static IP Ad dres sing” on page 1–1 1 . 9. In the EthernetBlaster login ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 13

    Altera Corporation 1–9 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble 1 These steps assume no changes have been made to the default factory settings. 1. Disconnect the power cable from the cir cuit board. 2. Plug the EIA/TIA 568B connector of a crossover CA T 5 UTP 4-pair patch cable ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 14

    1–10 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup Figure 1–7. Direct Connection to a Computer Us ing a Standard Cable and a Crossover Adapter 3. Connect the 10-pin female plug of the flexible, PCB-shielded cable labeled “BLASTER SIDE” to the 10-pin female tar get port on the Ethernet communica ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 15

    Altera Corporation 1–11 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble 7. In the EthernetBlaster login window , enter admin as the login and password as the default passwor d. The EthernetBlaster Status page opens display ing the status o f your EthernetBlaster communications cable in ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 16

    1–12 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup Figure 1–8. EthernetBlaster Change Settings Page 3. Click Apply . The EthernetBlaster comm unications cable automatically restarts. When the status LED r eturns to a steady green state, the Etherne tBlas ter communi cations cable has successfully r ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 17

    Altera Corporation 1–13 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble 2. Click the Change Settings tab and select DHCP from the Connection T ype menu. See Figur e 1–8 below . Figure 1–9. EthernetBlaster Change Settings Page 1 Contact your network administrator if you do not know ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 18

    1–14 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup 2. Choose Programmer (T ools menu). 3. Click Hardware Setup . The Hardware Settings tab of the Ha rdware Setup dialog box is displayed. 4. Click Add Hardware . The Add Hardware dialog box is displayed. Select EthernetBlaster and click Auto Detect . 1 ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 19

    Altera Corporation 1–15 December 2004 EthernetBlaster Communications Cable User Guide About the EthernetBlaster Communications Ca ble 8. In the Mode list, select the desir ed mode (Pr ogrammer windo w). T able 1–2 describes each mode. 1 The EthernetBl aster communica tions cable supports the Joint T est Action Group (JT AG), Passive Serial Prog ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 20

    1–16 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Cable Setup 1 See “Setting Up the EthernetBla ster Hardwar e in the Quartus II Software” on pa ge 1–13 for instr uctions to add the Ethernet Blaster co mmunications c able back i nto the Quartus II Programmer Hard ware setup. f For details about pr ogrammi ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 21

    Altera Corporation 2–1 December 2004 Chapter 2. EthernetBlaster Comm unications Cab le Administration Introduction This chapter describes how to ad minist er your EthernetB laster communications cable: ■ Managing Pas swor ds ● Changing the Administrative Password ● Changing the Quartus ® II Remote Connection Password ■ Resetting the Hard ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 22

    2–2 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Managing Passw or ds 1 When you change the Quartus II remote connection passwor d, client systems using the Ethern etBlaster communications cable must remove the har dware fr om their Quartus II Programmer ha rd wa re s et u p. S e e C h ap t er 1 , “Removing t ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 23

    Altera Corporation 2–3 December 2004 EthernetBlaster Communications Cable User Guide EthernetBlaster Communications Cable Administration The new passwor d takes ef fect immediately when logging back into the administrative web page. 1 The Etherne tBlaster comm unications c able does not restart when the administrative password is r eset. Changing ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 24

    2–4 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Resetting the Hardware The EthernetBlaster com munications cable restarts. When the status LED emits a stea dy green light, the EthernetBlaster ha s successfully rese t and the new passwor d is ef fective. Resetting the Hardware The EthernetBl aster commun icatio ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 25

    Altera Corporation 2–5 December 2004 EthernetBlaster Communications Cable User Guide EthernetBlaster Communications Cable Administration 1 When the EthernetBlaster is rese t, existing client systems using passwords other than the factory default must r emove the EthernetBlaster hardwar e from their Quartus II Programmer Hard wa re S et up. Se e C ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 26

    2–6 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Firmware Upgrade Figure 2–4. Upgrade Firmware Page 3. Click Browse and then locate and select the firmware file on your system. Click Apply . The EthernetBl aster commun ications cable r estarts automatically after the firmware has been succ essfully upgraded. ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 27

    Altera Corporation 3–1 December 2004 Chapter 3. EthernetBlaster Comm unications Cab le Specifications Over view This chapter provides compr e hensive information about the EthernetBlaster commun ications cable, includi ng the following: ■ EthernetBlaster ha rdwar e connections ■ Operating conditions EthernetBlaster Hardware Connections The Et ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 28

    3–2 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 EthernetBlaster Hardware Connections EthernetBlaster Ethern et Jack Connection The Ethernet cable Ethernet jack connects to the EthernetBlaster communications cable Ethernet port . The Ethernet jack pin number designations ar e shown in Figure 3–1 below . Figur ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 29

    Altera Corporation 3–3 December 2004 EthernetBlaster Communications Cable User Guide EthernetBlaster Communications Cable User Guide Table 3–2 identifies the 10-pin female plug pin names and the corresponding programming mode. 1 The circuit boar d must supply V CC(T ARGET) and ground to the EthernetBlaster cable for the I/O drivers. Circuit Boa ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 30

    3–4 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Operating Conditio ns Figure 3–3. 10-Pin Male Header Dimensions Operating Conditions Tables 3–3 through 3–5 summarize the maximum ratings, recommended operating conditions, and DC operating conditions fo r the cable. 0.025 Sq . 0.235 0.100 0.100 Dimensions ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 31

    Altera Corporation 3–5 December 2004 EthernetBlaster Communications Cable User Guide EthernetBlaster Communications Cable User Guide References For more information on configurat ion and in-system programmability (ISP), see the fo llowing sour ces: ■ AN 39: IEEE 1 149.1 (JT AG) Boundary -Scan T esting in Altera Devices ■ AN 95: In-System Prog ...

  • Socket Mobile Ethernet Blaster Communications Cable - page 32

    3–6 Altera Corporation EthernetBlaster Communications Cable User Guide December 2004 Revision History ■ Refer to the following procedur es in Quartus II Help: ● Programmin g a Single Devic e or Multiple Devices in JT AG or Passive Serial Mode ● Programmin g a Single Device in Active Serial Pr ogramming Mode ● Selecting the Communications ...

Produzent Socket Mobile Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Socket Mobile Ethernet Blaster Communications Cable erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Socket Mobile
- Bedienungsanleitungen Ethernet Blaster Communications Cable
- Produktkarten Socket Mobile
- Informationsbroschüren
- oder Energieetiketten Socket Mobile Ethernet Blaster Communications Cable
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Socket Mobile Ethernet Blaster Communications Cable.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Socket Mobile Ethernet Blaster Communications Cable, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Socket Mobile Ethernet Blaster Communications Cable. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Socket Mobile Ethernet Blaster Communications Cable ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Socket Mobile Ethernet Blaster Communications Cable, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Socket Mobile Ethernet Blaster Communications Cable hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Socket Mobile Ethernet Blaster Communications Cable verständlich ist.

Eine gänzliche Bedienungsanleitung von Socket Mobile sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Socket Mobile Ethernet Blaster Communications Cable bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Socket Mobile Ethernet Blaster Communications Cable befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Socket Mobile Ethernet Blaster Communications Cable, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Socket Mobile Ethernet Blaster Communications Cable - die uns die ersten Schritte während der Nutzung von Socket Mobile Ethernet Blaster Communications Cable erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Socket Mobile Ethernet Blaster Communications Cable hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Socket Mobile Ethernet Blaster Communications Cable im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Socket Mobile Ethernet Blaster Communications Cable?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Socket Mobile Ethernet Blaster Communications Cable nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Socket Mobile Ethernet Blaster Communications Cable hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)