Bedienungsanleitung Bryant SYSTXBBUIZ01

16 Seiten 0.61 mb
Download

Zur Seite of 16

Summary
  • Bryant SYSTXBBUIZ01 - page 1

    NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. TABLE OF CONTENTS SAFETY CONSIDERATIONS .....................................................1 INTRODUCTION ..........................................................................1 INSTALLATION AND START-UP OVERVIEW ...

  • Bryant SYSTXBBUIZ01 - page 2

    B. Step 2 — Evolution Zone Control ™ Location and Wiring Considerations WARNING: ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or possible equipment damage. Disconnect Power before routing control wiring. All wiring must comply with national, local, and state codes. EVOLUTION ™ ZONE CONTROL LOCATION ? ...

  • Bryant SYSTXBBUIZ01 - page 3

    C. Step 3 — Installing Evolution Zone Control ™ WARNING: ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Before installing Evolution Zone Control ™ , turn off all power to equipment. There may be more than one power source to disconnect. 1. Turn off all power to equipment. 2. If an existing Use ...

  • Bryant SYSTXBBUIZ01 - page 4

    8. Match and connect thermostat wires to proper terminals on User Interface backplate. See wiring diagram Fig. 12, 13, and 14. A — Green = Data A B — Yellow = Data B C — White = 24VAC (Com) D — Red = 24VAC (Hot) NOTE: It is not mandatory that the above color code be used, but each ABCD connection in the system MUST be wired consis- tently. ...

  • Bryant SYSTXBBUIZ01 - page 5

    isolation relay coil to furnace or fan coil HUM and COM terminals will allow the Evolution Zone Control to automatically energize the HUM output during a call for humidification. The N.O. relay contacts will be used to energize the humidifier. See fan powered humidifier installation instructions for more details. WARNING: FIRE OR EQUIPMENT HAZARD F ...

  • Bryant SYSTXBBUIZ01 - page 6

    NOTE: Range of outdoor unit Btu selection is limited by model number of indoor unit installed. The Evolution Zone Control ™ will not allow an outdoor unit size that is not supported by the installed indoor unit. NOTE: On new system installations, the model and serial number will be recognized and displayed. On any indoor/outdoor board replacement ...

  • Bryant SYSTXBBUIZ01 - page 7

    QUICK START For first time installers, Quick Start will allow a quick start up of the Evolution Zone System before learning all the details of system operation. However, for the best possible comfort and operation refer to the Evolution Zone Control ™ Owner ’ s Manual. A. Set Day, Time & Desired Humidity 1. Flip down the door at the base of ...

  • Bryant SYSTXBBUIZ01 - page 8

    EQUIPMENT SUMMARY MENU An example screen is shown in Fig. 21: This screen shows indoor unit type and model number, outdoor unit type (and model number if a 2-speed unit), filter type, any accessories that are installed, and how many zones are recognized. INSTALL MENU This menu item will perform start-up process in order to learn all equipment in sy ...

  • Bryant SYSTXBBUIZ01 - page 9

    NORMAL airflow adjustment is used during dehumidifying. If duct sweating is an issue, selecting HIGH will increase the dehumidifying airflow and reduce the sweating. LOW HEAT RISE: • ON • OFF (default) Set this to ON if the system contains a bypass humidifier. The ON setting will increase the furnace low heat airflow. STAGING: • SYSTEM (defau ...

  • Bryant SYSTXBBUIZ01 - page 10

    Interval at which the Change Humidify Pad notification will be displayed. HUMIDIFY WITH FAN: • NO (default) • YES If YES, the humidifier will run with Continuous Fan operation if there is a humidify demand. VENTILATOR: NOTE: Only appears if ventilator is installed. CLEAN INTERVAL: • 60 to 180 days of actual operation (default=90) Interval at ...

  • Bryant SYSTXBBUIZ01 - page 11

    display. The word ″ FAIL ″ will also be displayed instead of the actual temperature for Zone 2. Reconnect Zone 2 sensor and try all remaining sensors one at a time in the system. Smart Sensors may also be checked, see Smart Sensor Installation Instructions for procedure. AIRFLOW LIMITS: • Low • Medium • High (default) • Maximum Because ...

  • Bryant SYSTXBBUIZ01 - page 12

    Service = LAST 10 SYSTEM FAULTS This screen will show last 10 faults that occurred throughout the system. Each fault has the time and date incident recorded. Service technician should enter current date in ″ TODAY ’ S DATE ″ menu section BEFORE checking and logging the last 10 system faults. Each fault has a two-letter acronym preceding the f ...

  • Bryant SYSTXBBUIZ01 - page 13

    TROUBLESHOOTING Evolution Zone Control ™ does not power up. 1. Recheck wiring to ABCD on all devices. 2. Make sure all colors match for every terminal. 3. Make sure power is applied to the indoor unit, and the amber LED is lit on indoor control circuit board. 4. Check for 24VAC between the C and D terminals at Evolution Zone Control ™ terminal ...

  • Bryant SYSTXBBUIZ01 - page 14

    14 ...

  • Bryant SYSTXBBUIZ01 - page 15

    15 ...

  • Bryant SYSTXBBUIZ01 - page 16

    © 2004 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231 — 16 — Printed in U.S.A. iiuiz01-0-1 Catalog No. 809-60024 ...

Produzent Bryant Kategorie Thermostat

Dokumente, die wir vom Produzenten des Geräts Bryant SYSTXBBUIZ01 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bryant
- Bedienungsanleitungen SYSTXBBUIZ01
- Produktkarten Bryant
- Informationsbroschüren
- oder Energieetiketten Bryant SYSTXBBUIZ01
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bryant SYSTXBBUIZ01.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bryant SYSTXBBUIZ01, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bryant SYSTXBBUIZ01. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bryant SYSTXBBUIZ01 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bryant SYSTXBBUIZ01, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bryant SYSTXBBUIZ01 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bryant SYSTXBBUIZ01 verständlich ist.

Eine gänzliche Bedienungsanleitung von Bryant sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bryant SYSTXBBUIZ01 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bryant SYSTXBBUIZ01 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bryant SYSTXBBUIZ01, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bryant SYSTXBBUIZ01 - die uns die ersten Schritte während der Nutzung von Bryant SYSTXBBUIZ01 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bryant SYSTXBBUIZ01 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bryant SYSTXBBUIZ01 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bryant SYSTXBBUIZ01?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bryant SYSTXBBUIZ01 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bryant SYSTXBBUIZ01 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)