Deutsch dropdown-ico

Bedienungsanleitung Quantum Quantum Composers

31 Seiten 0.07 mb
Download

Zur Seite of 31

Summary
  • Quantum Quantum Composers - page 1

    1 1 INTRODUCTION This manual is designed to help you quickly and easily learn to use your Quantum Compo s ers Model 9412/9412A pulse generator. Rather than the usual array of knobs and switches, the 9412/9412A uses a menu - driven user interface with "on - line" he lp -- once you learn the basics of operating your 9412/9412A, you may neve ...

  • Quantum Quantum Composers - page 2

    2 Custom Modifications The 9412/9412A is microprocessor - controlled and employs a flexible and expandable user - interface. New features and operating modes often can be added, without hardware modif i- cations, by merely modifying the software contained inside the 9412/9412A. Most modific a- tions can be made for a very modest charge -- conta ct ...

  • Quantum Quantum Composers - page 3

    3 6. Never work alone. Someone should always be nearby to render aid if necessary. Training in CPR first aid is highly recommended. ...

  • Quantum Quantum Composers - page 4

    4 ...

  • Quantum Quantum Composers - page 5

    5 1 Item Button ...

  • Quantum Quantum Composers - page 6

    6 1 CONTROLS AND CONNECT ORS This chapter explains the function of each control and connector on the 9412/9412A. Front Panel The front panel contains the most frequently used controls and connectors. Display The 9412/9412A features a backlit liquid crystal display, which displays menu selections and settings. The left half of the display shows the ...

  • Quantum Quantum Composers - page 7

    7 Left Button (help) For numeric items, this button is used to select which digit in a numeric entry is selected for editing. For other items or when the left most digit is already selected for numeric i tems, pressing and holding this button down displays a brief description of the current item. Right Button (range) For numeric items, this button ...

  • Quantum Quantum Composers - page 8

    8 T2 Channel 2 output -- designed specifically for use as a solid - stat e laser Q - switch trigger and has all the capabilities of the other output channels, including several special modes which a f- fect only the output of Channel 2. Ext/Gate External Trigger or Gate signal input -- used as either an external signal to trigger the gener a- tion ...

  • Quantum Quantum Composers - page 9

    9 ...

  • Quantum Quantum Composers - page 10

    10 1 ...

  • Quantum Quantum Composers - page 11

    11 1 ...

  • Quantum Quantum Composers - page 12

    12 1 OPERATING INSTRUCTIO NS This chapter presents detailed instructions on the operation of the 9412/9412A. Overview The 9412/9412A uses a single - line L CD to display menu selections. The front panel keys are used to "navigate" through sets of menus to set various options and control the pulse ge n era- tor. Some keys are only active a ...

  • Quantum Quantum Composers - page 13

    13 Main Menu The Main Menu consists of a set of menu selections used to set the operating mode, time p e- riod and frequency of the 9412/9412A. MODE - Pulse Modes There are five (5) different Pulse modes available. Continuous Mode While in Continuous mode, the 9412/9412A will generate pulses at the rate set by the inte r nal To Period as set in the ...

  • Quantum Quantum Composers - page 14

    14 Duty Cycle The Duty Cycle mode is similar to Continuous mode in that a continuous stream of pulses is output. The exception is the outputs are only active for a set number of seconds ( DC:On menu), then disabled for another set time period ( DC:Off menu) before being re - enabled. This cycle is repeated for a set number of times ( CYCLES menu), ...

  • Quantum Quantum Composers - page 15

    15 ToPer - To Period Except when in External Trigger or Single Shot mode, all pulse outputs are based on an i n te r- nal timer called To. This menu is used to select the rate at which To runs by selecting the time period in microseconds between timer pulses. When in Continuous, Burst, or Duty C y cle mode, pulses are out put at the rate determined ...

  • Quantum Quantum Composers - page 16

    16 When set to Positive , the output will initially be at 0 Volts. When active, will go high for the specified pulse width time, after which it will return to 0. The voltage level while high w ill d e- pend upon the load and the setting of the output voltage adjustment on the back panel. If set to Negative , the output will normally be at the high ...

  • Quantum Quantum Composers - page 17

    17 T2:Wait The output of Channel 2 can be delayed for a number of pulses. This menu is used to set the number of pulses that must occur on the other channels before the output o f Channel 2 is e n- abled. This is particularly useful when using Channel 2 as a Q - switch trigger, as it allows the laser to thermally stabilize before activa t ing the Q ...

  • Quantum Quantum Composers - page 18

    18 RECALL Configuration Recalls a previously stored configuration from the specified memory location. To rec all a configuration use the Up and Down arrow keys to select the memory location number and press the Left or Right arrow key. You will be prompted to press the key to verify that you want to overwrite the active configuration. If you press ...

  • Quantum Quantum Composers - page 19

    19 ...

  • Quantum Quantum Composers - page 20

    20 1 5 4 3 2 1 9 8 7 6 ...

  • Quantum Quantum Composers - page 21

    21 1 COMPUTER INTERFACE The 9412/9412A comes standard with an RS232 serial interface. All menu settings can be set and retrieved over the computer interface using a simple command language. Serial (RS232) Pinout The serial port is located on the back of the 9412/9412A and uses a 9 - pin D - type connector with the following pinout (as viewed from t ...

  • Quantum Quantum Composers - page 22

    22 P P CR is a carriage return character (ASCII value 13). With echo enabled, all characters sent will be echoed back to the sender. Unidentified commands and most out of range conditions result in the pulse generator igno r ing the command. If the command is properly identified, the pulse generator returns an ok fo l- lo wed by a carriage return a ...

  • Quantum Quantum Composers - page 23

    23 Communication Protocol Communication parameters are set at 9600 baud, 8 bits, parity = none, and 1 stop bit. To help establish RS232 communications, the pulse generator emits the characters QC a p proximately every 200 ms after power up and until the 9412/9412A receives a $ . ...

  • Quantum Quantum Composers - page 24

    24 Command List The following table summarizes all the commands. Note: The name of each command is identical to how it appears on the dis play of the 9412/9412A. ...

  • Quantum Quantum Composers - page 25

    25 9412/9412A Communication Commands Command Name Parameters Description MODE 0 = Continuous mode 1 = Burst mode 2 = Duty Cycle mode 3 = Single Shot mode 4 = External Trigger mode Sets the pulse generator mode. GATE 0 = off 1 = active low 2 = active high Enables the external trigger input to function as a gate controlling all outputs. Cannot be use ...

  • Quantum Quantum Composers - page 26

    26 9412/9412A Communication Commands RECALL 0 - 4 (9412) 0 - 8 (9412A) Recall a stored configuration. STORE 1 - 4 (9412) 1 - 8 (9412A) Store a configuration. SHOTS (9412A Only) 0 = Reset to zero Resets shot counter. SHOT ? will return the number of shots. ECHO 0 = Disable 1 = Enable Enables/Disables the RS232 echo. The result string is always sent ...

  • Quantum Quantum Composers - page 27

    27 1 SPECIFICATIONS DELAYS P CHANNELS Two (2) independent outputs, with digitally controlled delay and pulsewidth. P DELAY 0 to 99.999999 sec P PULSEWIDTH 10 µ s to 99.999999 sec P RESOLUTION 1 µ s P ACCURACY 100 ns + .0002 x delay P TIMEBASE 8 MHz, 50 PPM crystal oscillator P RMS JITTER 50 ns + .0002 x period, 200 ns max P TRIG DELAY Ext Trig to ...

  • Quantum Quantum Composers - page 28

    28 OUTPUTS (T1,T2) P IM PEDANCE 50 Ω P SLEW RATE > .2 V/ns P OVERSHOOT < 100 mV + 10% of pulse amplitude P AMPLITUDE 1 - 10V into 50 Ω load 2 - 20V into high impedance load manually adjusted, all outputs at same level P PEAK CURRENT 400 mA per channel P AVERAGE CURRENT 200 mA average (total for all channels) COMPUTER INTERFACE P RS232 960 ...

  • Quantum Quantum Composers - page 29

    29 1 MAINTENANCE Except for fuse replacement, the 9412/9412A should require no maintenance. Replacing the Fuse The fuse is mounted on the circuit board located inside the 9412/9412A. Remove the top cover to access and follow the instructions given below to replace the fuse: 1. Unplug the 9412/9412A from power source and remove power cord from the b ...

  • Quantum Quantum Composers - page 30

    30 ...

  • Quantum Quantum Composers - page 31

    31 1 CUSTOM FEATURES None. ...

Produzent Quantum Kategorie Medical Alarms

Dokumente, die wir vom Produzenten des Geräts Quantum Quantum Composers erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Quantum
- Bedienungsanleitungen Composers
- Produktkarten Quantum
- Informationsbroschüren
- oder Energieetiketten Quantum Quantum Composers
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Quantum Quantum Composers.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Quantum Quantum Composers, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Quantum Quantum Composers. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Quantum Quantum Composers ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Quantum Quantum Composers, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Quantum Quantum Composers hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Quantum Quantum Composers verständlich ist.

Eine gänzliche Bedienungsanleitung von Quantum sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Quantum Quantum Composers bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Quantum Quantum Composers befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Quantum Quantum Composers, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Quantum Quantum Composers - die uns die ersten Schritte während der Nutzung von Quantum Quantum Composers erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Quantum Quantum Composers hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Quantum Quantum Composers im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Quantum Quantum Composers?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Quantum Quantum Composers nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Quantum Quantum Composers hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)