Deutsch dropdown-ico

Bedienungsanleitung Windsor SC20

29 Seiten 4.11 mb
Download

Zur Seite of 29

Summary
  • Windsor SC20 - page 1

    Read these instructions before using the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen MODELS: SC20 SCC20 10052190 10052230 SC20T SCC20T 10052200 10052240 SCX20T SCXC20T 10052370 10052420 Operating Instructions Bedienungsanleitung 86038350 01/29/07 PRV NO. 98712 BA WALK BEHIND SCRUBBER IPX4 ...

  • Windsor SC20 - page 2

    MACHINE DATA LOG/OVERVIEW SABER (SC) 86038350 01/29/07 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ___________________________________ ______________________________ _____________ Address: __________________ ___________________________________ ______________________________ __________ ...

  • Windsor SC20 - page 3

    TABLE OF CONTENTS SABER (SC) 86038350 01/29/07 3 Machine Data Log/Overview. ........................ 2 Table of Contents .......................................... 3 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1-1 SAFETY Important Safety Instructions ........................ 2-1 Hazard Intensity Level. .......... ...

  • Windsor SC20 - page 4

    HOW TO USE THIS MANUAL SABER (SC) 86038350 01/29/07 1-1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authori zed Windsor dealers. ...

  • Windsor SC20 - page 5

    SABER (SC) 86038350 01/29/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as descri ...

  • Windsor SC20 - page 6

    HAZARD INTENSITY LEVEL SABER (SC) 86038350 01/29/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY . The level of hazard intensity is determined by the following definition ...

  • Windsor SC20 - page 7

    SAFETY LABEL LOCATION SABER (SC) 86038350 01/29/07 2-3 NOTE: These drawings indicate the location of safet y labels on the machine . If at any time the labels becom e illegible, promptly replace them. SAFETY DECAL 86252530 PRV NO. 81494 BATTERY C AUTION 86252520 PRV NO. 80885 CAUTION Explosive Gas is Given Off By Batteries During Charge. Cover Open ...

  • Windsor SC20 - page 8

    TECHNICAL SPECIFICATIONS SABER (SC) 86038350 01/29/07 3-1 ITEM DIMENSION/CAPACIT Y Nominal power – non-traction model 1100 W Nominal power – traction model 1200 W Rated Voltage 24VDC Rated Amperage – non-traction model 45 Amps Rated Amperage – traction model 50 Amps Batteries 2 x 12 Volt 105-130-195 AH @ 20hr rate Scrub Brush Motor .75 hp ( ...

  • Windsor SC20 - page 9

    TECHNICAL SPECIFICATIONS SABER (SC) 86038350 01/29/07 3-2 ITEM MEASURE Height 43 in. ( 109.2 cm) Length 54 in. (137.1 cm) Width without squeegee 22 in. (55.9 cm) Width of squeegee 31 in. ( 78.7 cm) Width of scrub path 20 in. (51 cm) SPECIAL NOTES: The A-weighted sound pressure level emitted by the appliance was measured to be 72.5 dBA. This is a sp ...

  • Windsor SC20 - page 10

    HOW THE MACHINE WORKS SABER (SC) 86038350 01/29/07 3-3 The Saber Compact is a battery powered, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with a brush, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution ...

  • Windsor SC20 - page 11

    COMPONENTS SABER (SC) 86038350 01/29/07 3-4 1. Control Panel 2. Control Handle 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head 6. Scrub Brush Access Cover 7. Solution Tank 8. Solution Tank Cover 9. Solution Tank Drain Hose 10. Solution Strainer 11. Solution Tank Support Arm 12. Squeegee 13. Vacuum Motor 8 2 1 4 9 12 3 10 13 11 5 7 6 ...

  • Windsor SC20 - page 12

    CONTROLS – NON-TRACTION SABER (SC) 86038350 01/29/07 3-5 1. Brush Switch 2. Brush Lift Lever 3. Vacuum Switch 4. Squeegee Lift Lever 5. Solution Control Lever 6. Battery Charge Level Indicator 7. Hour Meter (Optional) 8. Circuit Breakers 6 2 4 3 1 5 2% 8 7 ...

  • Windsor SC20 - page 13

    CONTROLS – NON TRACTION SABER (SC) 86038350 01/29/07 3-6 1. BRUSH SWITCH Controls the scrub brush motor. To turn scrub brush on, press the top of the switch. To turn scrub brush off, press the bottom of the switch. 2. BRUSH LIFT LEVER Raises and lowers the brush. To lower the brush, lift the lever from the notch, move to the left, then lower. To ...

  • Windsor SC20 - page 14

    CONTROLS - TRACTION SABER (SC) 86038350 01/29/07 3-7 1. Solution Control Knob 2. Brush Switch 3. Brush Lift Lever 4. Vacuum Switch 5. Squeegee Lift Lever 6. Key Switch 7. Propel Buttons (Normally Forward) 8. Reverse Propel Button 9. Speed Control Knob 10. Battery Charge Level Indicator 11. Emergency Shut Off Switch (Optional) 12. Hour Meter (Option ...

  • Windsor SC20 - page 15

    CONTROLS - TRACTION SABER (SC) 86038350 01/29/07 3-8 1. SOLUTION CONTROL KNOB Controls solution flow to scrub deck. To increase flow, rota te knob clockwise. To decrease flow, rotate knob counterclockwise. If the brush motor is turned off or the direction control lever is in neutral, the flow is automatically interrupt ed until the motor is turned ...

  • Windsor SC20 - page 16

    CONTROLS - TRACTION SABER (SC) 86038350 01/29/07 3-9 9. SPEED CONTROL KNOB Controls the speed of the machine. To increase speed, rotate knob clockwise. To decrease speed, rotate knob counterclockwise. 10. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bars illuminated ...

  • Windsor SC20 - page 17

    MACHINE OPERATION SABER (SC) 86038350 01/29/07 3-10 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. NOTE: See maintenance section for pre-run machine inspection checklist items. STARTING MACHINE NOT ...

  • Windsor SC20 - page 18

    MACHINE OPERATION SABER (SC) 86038350 01/29/07 3-11 TO BEGIN SCRUBBING When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. Flammable liquids and/or reactive metals can cause explosions or fire! Do not pick up. 1. Turn the machine power on. 2. Lower the squeegee. 3. Turn the vacuu ...

  • Windsor SC20 - page 19

    MACHINE OPERATION SABER (SC) 86038350 01/29/07 3-12 EMPTYING AND CLEANI NG TANKS 1. Park the machine next to a floor drain. Drain hoses are on the rear of the machine. 2. Turn the machine power off. SOLUTION TANK 1. Unhook the small drain hose from the retainer. Unscrew the T-handle plug enough to loosen it, then lower the hose in the direction of ...

  • Windsor SC20 - page 20

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-1 BATTERIES The batteries provide the power to operate the machine. The batteries require regular maintenance to keep t hem operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times. To get the greatest life f ...

  • Windsor SC20 - page 21

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-2 CHECKING BAT TERY SPECIFIC GRAVITY Use a hydrometer to check the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the reading may not be accurate. Check the hydrometer r ...

  • Windsor SC20 - page 22

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-3 4. Check the electrolyte level in each battery cell. Before charging, add just enough distilled water to cover the plates. After charging is complete, add just enough distilled water to bring up the level to the indicator ring. If the water level is too high before charging, normal expan sion rate of the ...

  • Windsor SC20 - page 23

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-4 SCRUB BRUSHES NOTE: All original equipment brushes a re equi pped with “Perform Alert © ”. This feature will tell the operator when it is time to replace the scrub brush. “Perform Alert © ” brush es have pre-trimm ed bright yellow tufts to indicate the length of a worn out brush. When the tufts ...

  • Windsor SC20 - page 24

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-5 SCRUB BRUSHES NOTE: All original equipment brushes a re equi pped with “Perform Alert © ”. This feature will tell the operator when it is time to replace the scrub brush. “Perform Alert © ” brush es have pre-trimm ed bright yellow tufts to indicate the length of a worn out brush. When the tufts ...

  • Windsor SC20 - page 25

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-6 SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade into the squee gee assembly while maintaining vacuum to provide lift. The rear blade wipes the floor to a nea r dry condition. It is important the rear blade be in good condition to properly do its job. Check b ...

  • Windsor SC20 - page 26

    MAINTENANCE SABER (SC) 86038350 01/29/07 4- 7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch and v a cuum switch. Lower t h e squeegee and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back. FOR SAFETY: Before le av ing or servicing the mach ...

  • Windsor SC20 - page 27

    MAINTENANCE SABER (SC) 86038350 01/29/07 4-8 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS 200 HRS Check batteries after cha rging; add water if necessary * Check pad wear to prevent buildup of chemicals * Check linkages and co nnectors for wear and damage * Check hos es for wear , blockages , or damage * Clean squeegee; check fo r adju ...

  • Windsor SC20 - page 28

    MACHINE TROUBLESHOOTING SABER (SC) 86038350 01/29/07 4-9 PROBLEM CAUSE SOLUTION Poor or no water pick-up Debris caught on squeegee Remove debris Worn squeegee blades Replace squeegee blades Vacuum hose clogged Clear obstruction from hose Vacuum hose disconnected from squeegee or recovery tank Reconnect vacuum hose Vacuum hose damaged Replace vacuum ...

  • Windsor SC20 - page 29

    MACHINE TROUBLESHOOTING SABER (SC) 86038350 01/29/07 4-10 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set too low Turn on or increase flow setting Solution strainer plugged Clean solution strainer Solution hoses obstructed Clear obstruction from hose Solution sole ...

Produzent Windsor Kategorie Vacuum Cleaner

Dokumente, die wir vom Produzenten des Geräts Windsor SC20 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Windsor
- Bedienungsanleitungen SC20
- Produktkarten Windsor
- Informationsbroschüren
- oder Energieetiketten Windsor SC20
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Windsor SC20.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Windsor SC20, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Windsor SC20. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Windsor SC20 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Windsor SC20, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Windsor SC20 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Windsor SC20 verständlich ist.

Eine gänzliche Bedienungsanleitung von Windsor sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Windsor SC20 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Windsor SC20 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Windsor SC20, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Windsor SC20 - die uns die ersten Schritte während der Nutzung von Windsor SC20 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Windsor SC20 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Windsor SC20 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Windsor SC20?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Windsor SC20 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Windsor SC20 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)