Deutsch dropdown-ico

Bedienungsanleitung Hitachi CP-AW250N

32 Seiten 1.53 mb
Download

Zur Seite of 32

Summary
  • Hitachi CP-AW250N - page 1

    1 NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC. • Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector . • Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of ...

  • Hitachi CP-AW250N - page 2

    2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be dif ferent. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data Data H. Sync. V. Sync. Sync (A ...

  • Hitachi CP-AW250N - page 3

    3 Connection to the por ts Connection to the ports NO TICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port. COMPUTER IN1 COMPUTER IN2 HDMI USB TYPE B S-VIDEO VIDEO AUDIO OUT AUDIO IN3 AUDI ...

  • Hitachi CP-AW250N - page 4

    4 D S-VIDEO Mini DIN 4pin jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43, P AL(60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (P AL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Connection to the por ts (continued) 4 3 2 1 E VIDEO RCA jack ...

  • Hitachi CP-AW250N - page 5

    5 Connection to the por ts (continued) G AUDIO IN1, H AUDIO IN2 Ø3.5 stereo mini jack • 200 mV rms, 47kΩ terminator AUDIO IN3 I R, J L RCA jack x2 • 200 mV rms, 47kΩ terminator AUDIO OUT K R, L L RCA jack x2 • 200 mV rms, 1kΩ output impedance M MIC Ø3.5 mono mini jack <Low level> • 2 mV rms, 1kΩ terminator <High level> ...

  • Hitachi CP-AW250N - page 6

    6 Connection to the por ts (continued) O USB TYPE B USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground 4 3 2 1 P CONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the section "RS-232C Communication". Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CT ...

  • Hitachi CP-AW250N - page 7

    7 Connection to the por ts (continued) T o input component video signal to COMPUTER IN ports ex. T o input component video signal to the COMPUTER IN1 or IN2 port of the projector , use a RCA to D-sub cable or adapter . For about the pin description of the required cable or adapter , refer to the descriptions about COMPUTER IN1 and IN2 port ( & ...

  • Hitachi CP-AW250N - page 8

    8 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer . For details of RS-232C commands, refer to RS-232C Communication / Network command table ( & 17 ). Connection 1. T urn off the projector and the computer . 2 ...

  • Hitachi CP-AW250N - page 9

    9 RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps,8N1 2. Command for mat ("h" shows hexadecimal) Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12 Command Action Header Data Header code Packet Data size CRC ag Action T ype Setting code L H L H L H L H L H L H <SET> Change setting to desired value [(cL)(cH)] by ...

  • Hitachi CP-AW250N - page 10

    10 RS-232C Communication (continued) 3. R esponse code / Er r or code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly , the projector changes the setting data for the specied item by [T ype], and it returns the code. (2) NAK reply : 15h When the projecto ...

  • Hitachi CP-AW250N - page 11

    11 Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser . For details of RS-232C commands, refer to RS-232C Communication / Network command table ( & 17 ). Connection 1. T urn off the projector and the computer . 2. Connect the projector&ap ...

  • Hitachi CP-AW250N - page 12

    12 Communicaion P or t The following two ports are assigned for the command control. TCP #23 TCP #9715 Congure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Netwo rk Control Port1 (Port: 23)] to use TCP #23. Default setting is ? ...

  • Hitachi CP-AW250N - page 13

    13 Command Control via the Networ k (continued) Command control settings [TCP #23] 1. Command for mat Same as RS-232C communication, refer to R S-232C Communicaton command format. 2. R esponse code / Er r or code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4). One au ...

  • Hitachi CP-AW250N - page 14

    14 2. R esponse code / Er r or code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (1) ACK reply : 06h + ××h ( ××h : connection ID ) (2) NAK reply : 15h + ××h (3) Error reply : 1Ch + 0000h + ××h (4) Data reply : 1 ...

  • Hitachi CP-AW250N - page 15

    15 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that i s connected with this projector by RS-232C communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge Function - Network Guide. Connection 1. Conn ...

  • Hitachi CP-AW250N - page 16

    16 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICA TION menu. ( & OPTION menu - SERVICE - COMMUNICA TION in the User's Manual - Operating Guide ) Item Condition BAUD RA TE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (xed) P ARITY NONE/ODD/EVEN Start bit 1 bit (xed) Stop bit 1 bi ...

  • Hitachi CP-AW250N - page 17

    17 RS-232C Communication / Network command table Names Operation T ype Header Command Data CRC Action T ype Setting code Power Set T urn off BE EF 03 06 00 2A D3 01 00 00 60 00 00 T urn on BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 19 D3 02 00 00 60 00 00 [Example return] 00 00 01 00 02 00 [Off] [On] [Cool down] Input Source Set COMP ...

  • Hitachi CP-AW250N - page 18

    RS-232C Communication / Netw ork command ta ble (continued) 18 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code CONTRAST Reset Execute BE EF 03 06 00 A4 D2 06 00 01 70 00 00 GAMMA Set 1 DEF AUL T BE EF 03 06 00 07 E9 01 00 A1 30 20 00 1 CUSTOM BE EF 03 06 00 07 FD 01 00 A1 30 10 00 2 DEF AUL T BE EF 0 ...

  • Hitachi CP-AW250N - page 19

    RS-232C Communication / Netw ork command ta ble (continued) 19 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code User Gamma Point 7 Get BE EF 03 06 00 80 FE 02 00 96 30 00 00 Increment BE EF 03 06 00 E6 FE 04 00 96 30 00 00 Decrement BE EF 03 06 00 37 FF 05 00 96 30 00 00 User Gamma Point 7 Reset Execu ...

  • Hitachi CP-AW250N - page 20

    RS-232C Communication / Netw ork command ta ble (continued) 20 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code COLOR TEMP OFFSET B Get BE EF 03 06 00 BC F4 02 00 B7 30 00 00 Increment BE EF 03 06 00 DA F4 04 00 B7 30 00 00 Decrement BE EF 03 06 00 0B F5 05 00 B7 30 00 00 COLOR TEMP OFFSET B Reset Exe ...

  • Hitachi CP-AW250N - page 21

    RS-232C Communication / Netw ork command ta ble (continued) 21 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code H POSITION Get BE EF 03 06 00 F1 82 02 00 01 21 00 00 Increment BE EF 03 06 00 97 82 04 00 01 21 00 00 Decrement BE EF 03 06 00 46 83 05 00 01 21 00 00 H POSITION Reset Execute BE EF 03 06 0 ...

  • Hitachi CP-AW250N - page 22

    RS-232C Communication / Netw ork command ta ble (continued) 22 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code HDMI RANGE Set AUTO BE EF 03 06 00 86 D8 01 00 22 20 00 00 NORMAL BE EF 03 06 00 16 D9 01 00 22 20 01 00 ENHANCED BE EF 03 06 00 E6 D9 01 00 22 20 02 00 Get BE EF 03 06 00 B5 D8 02 00 22 20 ...

  • Hitachi CP-AW250N - page 23

    RS-232C Communication / Netw ork command ta ble (continued) 23 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code PERFECT FIT Left T op -H Get BE EF 03 06 00 31 89 02 00 21 21 00 00 Increment BE EF 03 06 00 57 89 04 00 21 21 00 00 Decrement BE EF 03 06 00 86 88 05 00 21 21 00 00 PERFECT FIT Left T op -V ...

  • Hitachi CP-AW250N - page 24

    RS-232C Communication / Netw ork command ta ble (continued) 24 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code ECO MODE Set NORMAL BE EF 03 06 00 3B 23 01 00 00 33 00 00 ECO BE EF 03 06 00 AB 22 01 00 00 33 01 00 Get BE EF 03 06 00 08 23 02 00 00 33 00 00 MIRROR Set NORMAL BE EF 03 06 00 C7 D2 01 00 ...

  • Hitachi CP-AW250N - page 25

    RS-232C Communication / Netw ork command ta ble (continued) 25 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code VOLUME - S-VIDEO Get BE EF 03 06 00 75 CD 02 00 62 20 00 00 Increment BE EF 03 06 00 13 CD 04 00 62 20 00 00 Decrement BE EF 03 06 00 C2 CC 05 00 62 20 00 00 VOLUME - VIDEO Get BE EF 03 06 0 ...

  • Hitachi CP-AW250N - page 26

    RS-232C Communication / Netw ork command ta ble (continued) 26 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code AUDIO SOURCE USB TYPE B Set OFF BE EF 03 06 00 AE DE 01 00 3C 20 00 00 AUDIO IN1 BE EF 03 06 00 3E DF 01 00 3C 20 01 00 AUDIO IN2 BE EF 03 06 00 CE DF 01 00 3C 20 02 00 AUDIO IN3 BE EF 03 06 ...

  • Hitachi CP-AW250N - page 27

    RS-232C Communication / Netw ork command ta ble (continued) 27 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code LANGUAGE Set POLSKI BE EF 03 06 00 97 D7 01 00 05 30 0E 00 TÜRKÇE BE EF 03 06 00 07 D6 01 00 05 30 0F 00 DANSK BE EF 03 06 00 A7 DF 01 00 05 30 1 1 00 ČESKY BE EF 03 06 00 57 DF 01 00 05 ...

  • Hitachi CP-AW250N - page 28

    RS-232C Communication / Netw ork command ta ble (continued) 28 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code TEMPLA TE Set TEST P A TTERN BE EF 03 06 00 43 D9 01 00 22 30 00 00 DOT -LINE1 BE EF 03 06 00 D3 D8 01 00 22 30 01 00 DOT -LINE2 BE EF 03 06 00 23 D8 01 00 22 30 02 00 DOT -LINE3 BE EF 03 06 ...

  • Hitachi CP-AW250N - page 29

    RS-232C Communication / Netw ork command ta ble (continued) 29 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code MY BUTT ON-1 Set COMPUTER IN1 BE EF 03 06 00 3A 33 01 00 00 36 00 00 COMPUTER IN2 BE EF 03 06 00 FA 31 01 00 00 36 04 00 LAN BE EF 03 06 00 0A 34 01 00 00 36 0B 00 USB TYPE A BE EF 03 06 00 ...

  • Hitachi CP-AW250N - page 30

    RS-232C Communication / Netw ork command ta ble (continued) 30 Names Operation T ype Header Command Data CRC Action T ype Setting code MY SOURCE Set COMPUTER IN1 BE EF 03 06 00 FA 38 01 00 20 36 00 00 COMPUTER IN2 BE EF 03 06 00 3A 3A 01 00 20 36 04 00 LAN BE EF 03 06 00 CA 3F 01 00 20 36 0B 00 USB TYPE A BE EF 03 06 00 5A 3B 01 00 20 36 06 00 USB ...

  • Hitachi CP-AW250N - page 31

    31 PJLink command PJLink command POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = COMPUTER IN 2 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B INPT ? Input Source inquiry 1 1 = COMPUTER IN 1 12 = COMPUTER I ...

  • Hitachi CP-AW250N - page 32

    32 PJLink command (continued) Commands Control Description Parameter or Response ERST ? Error Status inquiry 1st byte: Refers to Fan error; one of 0 to 2 2nd byte : Refers to Lamp error; one of 0 to 2 3rd byte: Refers to T emptrature error; one of 0 to 2 4th byte: Refers to Cover error; one of 0 to 2 5th byte: Refers to Filter error; one of 0 to 2 ...

Produzent Hitachi Kategorie Projector

Dokumente, die wir vom Produzenten des Geräts Hitachi CP-AW250N erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Hitachi
- Bedienungsanleitungen CP-AW250N
- Produktkarten Hitachi
- Informationsbroschüren
- oder Energieetiketten Hitachi CP-AW250N
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Hitachi CP-AW250N.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Hitachi CP-AW250N, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Hitachi CP-AW250N. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Hitachi CP-AW250N ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Hitachi CP-AW250N, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Hitachi CP-AW250N hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Hitachi CP-AW250N verständlich ist.

Eine gänzliche Bedienungsanleitung von Hitachi sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Hitachi CP-AW250N bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Hitachi CP-AW250N befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Hitachi CP-AW250N, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Hitachi CP-AW250N - die uns die ersten Schritte während der Nutzung von Hitachi CP-AW250N erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Hitachi CP-AW250N hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Hitachi CP-AW250N im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Hitachi CP-AW250N?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hitachi CP-AW250N nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hitachi CP-AW250N hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)