Bedienungsanleitung Vulcan-Hart EG60 ML-52488

24 Seiten 2.05 mb
Download

Zur Seite of 24

Summary
  • Vulcan-Hart EG60 ML-52488 - page 1

    INST ALLA TION & OPERA TION MANUAL VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 31053 Rev. A (4-98) EG SERIES GAS RANGES MODEL EG24 ML-52486 EG36 ML-52487 EG48 ML-114956 EG60 ML-52488 EG160 ML-52489 EG260 ML-52490 MODEL EG36 ...

  • Vulcan-Hart EG60 ML-52488 - page 2

    — 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OB ...

  • Vulcan-Hart EG60 ML-52488 - page 3

    — 3 — T ABLE OF CONTENTS EG SERIES GAS RANGE MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION . . . . . . . . . . . . . . . . . ...

  • Vulcan-Hart EG60 ML-52488 - page 4

    — 4 — EG SERIES GAS RANGE MODELS EG60 EG260 EG160 EG24 EG48 EG36 PL-53006 ...

  • Vulcan-Hart EG60 ML-52488 - page 5

    — 5 — Installation, Operation and Care of MODEL EG SERIES GAS RANGES KEEP THIS MANUAL FOR FUTURE REFERENCE GENERAL Vulcan ranges are produced with quality workmanship and material. Proper installation, usage and maintenance of your range will result in many years of satisfactory performance. Vulcan suggests that you thoroughly read this entire ...

  • Vulcan-Hart EG60 ML-52488 - page 6

    — 6 — PL-51219 CONNECT GAS LINE STRAIN RELIEF HERE The range must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearance for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of air in the room to allow for combustion of the gas at the burners. IN ...

  • Vulcan-Hart EG60 ML-52488 - page 7

    — 7 — Installation of Broiler/Griddle Bricks The broiler/griddle utilizes ceramic fire bricks for heat radiation of the burners. Install the broiler bricks before connecting the gas supply line. 1. Remove the six 5 1 ⁄ 4 " x 2 1 ⁄ 4 " (133.3 x 57 mm) and six 5 1 ⁄ 4 " x 5 1 ⁄ 16 " (133.3 x 128.6 mm) bricks from the s ...

  • Vulcan-Hart EG60 ML-52488 - page 8

    — 8 — Installation of Griddle Top Bricks The griddle top section is extremely heavy. It will require three people to install the griddle and griddle brick — two people to lift the griddle plate (Fig. 3) and one person to set the bricks and griddle thermostat capillary bulb(s) in place. Fig. 3 The griddle top section utilizes a two-fold baffle ...

  • Vulcan-Hart EG60 ML-52488 - page 9

    — 9 — 4. Exercise caution when placing brick in a thermostatically controlled griddle section. DO NOT hit thermostat bulb while installing bricks. The thermostat bulb is a sensitive device and may be easily knocked out of adjustment. Into the 6 1 ⁄ 2 " (165 mm) wide baffle, install: a. Two 10" x 4" (254 x 101.6 mm) bricks, plac ...

  • Vulcan-Hart EG60 ML-52488 - page 10

    — 10 — Installation of Hot Top Bricks The hot top sections utilize composite/mortar fire bricks for heat distribution of the burners. Install these bricks before connecting the gas supply line or installing the back riser. 1. The composite/mortar bricks are shipped in a rectangular cardboard box. Locate box and carefully remove two 10" x 4 ...

  • Vulcan-Hart EG60 ML-52488 - page 11

    — 11 — Fig. 5 Fig. 6 3. Assemble the required components as shown in Fig's. 5 and 6. 4. Lift the assembly up, sliding the channels into the space provided at the rear of the range (this may require two people). 5. It may be necessary to pull the heat shield bottom out slightly in order to clear the oven flue box area. Be sure the backsplas ...

  • Vulcan-Hart EG60 ML-52488 - page 12

    — 12 — 6. Install eight #10 sheet metal screws (4 to each channel leg) (Fig. 9). Fig. 9 7. From the front, install four 1 ⁄ 4 -20 x 2 5 ⁄ 16 " (58.7 mm) long machine screws and secure bolts with locknuts. Do not tighten the screws all the way down. Leave about 1 ⁄ 4 " (6.4 mm) of play in each screw (Fig. 10) 8. Lift the shelf up ...

  • Vulcan-Hart EG60 ML-52488 - page 13

    — 13 — LEVELING Check the leveling of the range. Place a carpenter's level inside the oven cavity across the oven rack(s). Level front-to-back and side-to-side. To adjust the leveling, tilt the range to one side, and using channel locks, unscrew the adjustable leg insert as required. Repeat this procedure as necessary for each leg. Casters ...

  • Vulcan-Hart EG60 ML-52488 - page 14

    — 14 — Fig. 12 A leak limiter is supplied with every regulator to allow excess gas pressure to escape. Do not obstruct leak limiter on gas pressure regulator, as obstruction may cause regulator to malfunction. WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS. USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME. Af ...

  • Vulcan-Hart EG60 ML-52488 - page 15

    — 15 — OPERA TION WARNING: THE RANGE AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE RANGE. CONTROLS THERMOSTAT DIAL — Allows operator to regulate oven temperature from low to 500 ° F (260 ° C). OPEN TOP BURNER KNOB — Regulates gas flow to top burners. To increase heat, turn knob counterclockwise; to decre ...

  • Vulcan-Hart EG60 ML-52488 - page 16

    — 16 — Open Top Burners 1. Turn main gas supply ON. 2. Wait 30 seconds and, using a taper, light the open top pilot (Fig. 14). Fig. 14 3. If pilot fails to light, turn main gas supply OFF. Wait 5 minutes and repeat the above procedures. 4. Turn one open top burner valve ON to remove air from the gas line. Turn burner valve OFF when gas begins t ...

  • Vulcan-Hart EG60 ML-52488 - page 17

    — 17 — 1. Open kick panel (Fig. 15) and lift up the pilot lighting hole cover. 2. Light pilot by depressing the reset button located behind the kick panel (Fig. 16). Continue to hold reset button in for 1 minute. If pilot fails to light, turn main gas supply OFF and wait 5 minutes before repeating Step 2. Fig. 15 Fig. 16 3. After pilot is lit, ...

  • Vulcan-Hart EG60 ML-52488 - page 18

    — 18 — RACK ARRANGEMENT Capacity The oven has two rack positions and is supplied with one oven rack. Additional racks may be obtained through a Vulcan-Hart parts depot. For best results when baking cakes and pastries, it is recommended that only a single rack position be utilized. However, proper rack usage and positioning is really determined ...

  • Vulcan-Hart EG60 ML-52488 - page 19

    — 19 — PREHEATING Oven Turn thermostat control to the desired cooking temperature and preheat oven for 25 minutes. To save on gas consumption, do not operate oven at maximum heat when it is not necessary. Turn thermostat down to 250 ° F (121 ° C) or OFF when oven is not in use or during idle cooking periods. Hot Top Burners Turn burner ON to ...

  • Vulcan-Hart EG60 ML-52488 - page 20

    — 20 — COOKING CHART Recommended temperatures and times are intended as a guide only. Adjustments must be made to compensate for elevation, variations in recipes, ingredients, preparation and personal preference on product appearance. Meat roasting is most satisfactory at temperatures of 225 ° F to 325 ° F (107 ° C to 162.7 ° C) for beef, l ...

  • Vulcan-Hart EG60 ML-52488 - page 21

    — 21 — RECOMMENDED TEMPERATURES AND TIMES FOR BAKING - Cont'd. PRODUCT TEMPERATURE APPROX. TIME (MIN.) Angel or Sponge Cakes Sheet pans 18 x 26 x 1" (457 x 661 x 25.4 mm) Scaled 5-6 lbs. (2.3-2.7 kg) per pan 300 to 325 ° F/148.9 to 162.8 ° C 15 to 20 Loaf or Tube Pans 315 to 340 ° F/157.2 to 171 ° C 20 to 30 Cup Cakes 350 to 400 ? ...

  • Vulcan-Hart EG60 ML-52488 - page 22

    — 22 — OVEN BROILING OR FRYING PRODUCT TEMPERATURE APPROX. TIME (MIN.) Hamburger Patties 8 per lb.(0.5 kg) - Med. well done 400 to 450 ° F/204.4 to 232.2 ° C 5 to 6 6 per lb. (0.5 kg) 400 to 450 ° F/204.4 to 232.2 ° C 7 to 10 4 per lb. (0.5 kg) 375 to 385 ° F/190.5 to 196 ° C 8 to 12 Fish Sticks & Portions Frozen bread. - 1 oz. (28.3 ...

  • Vulcan-Hart EG60 ML-52488 - page 23

    — 23 — CLEANING Do not use Dawn dish detergent to clean the exterior or interior components of the range. DO NOT use scouring powder. It is extremely difficult to remove completely, and accumulations can build up that will damage the oven. Vulcan painted surfaces may be cleaned using a soft cloth and mild detergent solution. RANGES Daily: Remov ...

  • Vulcan-Hart EG60 ML-52488 - page 24

    — 24 — Oven Door Gasket To clean the oven door gasket, use a soft cloth or sponge and a mild cleanser. DO NOT USE STRONG OVEN CLEANERS SUCH AS EASY OFF ® OR MR. MUSCLE ® . Cleaners of this nature will destroy the gasket material. GRIDDLE PLATE Cleaning the griddle section will produce evenly cooked, perfectly browned griddle products and will ...

Produzent Vulcan-Hart Kategorie Range

Dokumente, die wir vom Produzenten des Geräts Vulcan-Hart EG60 ML-52488 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Vulcan-Hart
- Bedienungsanleitungen EG60 ML-52488
- Produktkarten Vulcan-Hart
- Informationsbroschüren
- oder Energieetiketten Vulcan-Hart EG60 ML-52488
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Vulcan-Hart EG60 ML-52488.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Vulcan-Hart EG60 ML-52488, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Vulcan-Hart EG60 ML-52488. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Vulcan-Hart EG60 ML-52488 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Vulcan-Hart EG60 ML-52488, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Vulcan-Hart EG60 ML-52488 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Vulcan-Hart EG60 ML-52488 verständlich ist.

Eine gänzliche Bedienungsanleitung von Vulcan-Hart sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Vulcan-Hart EG60 ML-52488 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Vulcan-Hart EG60 ML-52488 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Vulcan-Hart EG60 ML-52488, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Vulcan-Hart EG60 ML-52488 - die uns die ersten Schritte während der Nutzung von Vulcan-Hart EG60 ML-52488 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Vulcan-Hart EG60 ML-52488 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Vulcan-Hart EG60 ML-52488 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Vulcan-Hart EG60 ML-52488?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Vulcan-Hart EG60 ML-52488 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Vulcan-Hart EG60 ML-52488 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)