Bedienungsanleitung Simplicity 7/22E

20 Seiten 0.41 mb
Download

Zur Seite of 20

Summary
  • Simplicity 7/22E - page 1

    O PERATOR ’ S M ANUAL Sno-Away Models 5-55cd22 7-55cd22 Mfg. No. 1691411 Mfg. No. 1691413 Mfg. No. 1691414 ...

  • Simplicity 7/22E - page 2

    BakerTM O PERATOR ’ S M ANUAL Model 7/22E ...

  • Simplicity 7/22E - page 3

    II 500 N. Spring Street, P.O. Box 997 Port Washinnton, WI 53074-0997 ...

  • Simplicity 7/22E - page 4

    ...

  • Simplicity 7/22E - page 5

    Table Of Contents SAFETY RULES General ........................................................... 2 Preparation.. .................................................. .2 Operation.. ..................................................... .2 Maintenance & Storage.. .............................. .3 Safety Decals .................................... ...

  • Simplicity 7/22E - page 6

    WARNING This unit is a “two-stage” snowthrower. The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur. To avoid injury, keep ...

  • Simplicity 7/22E - page 7

    Safety Rules l Always refer to the Operator’s Manual for important details if snowthrower is to be stored for an extended period. l Run auger drive a few seconds after completion of throwing snow to help clear out snow and prevent freeze-up. SAFETYDECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant remi ...

  • Simplicity 7/22E - page 8

    Controls SNOWTHROWER CONTROLS (Figure 1) Ref A B i C D E Name Auger Control Clutch Lever Drive Control Clutch Lever Chute Control Rod Chute Deflector Skid Shoes Function Engages auger/impeller when depressed; disengages when released. Engages drive to wheels when depressed; disengages when released. Controls direction snow is thrown. Controls angle ...

  • Simplicity 7/22E - page 9

    DEFLECTOR The angle and distance of the discharged snow is con- trolled by the position of the deflector. Engine speed also affects distance of discharge. The more the deflector is tilted back, the farther snow will be thrown. Loosen the knob (figure 3) to tilt the deflector back or forward, then retighten the knob. SCRAPER BAR & SKID SHOES On ...

  • Simplicity 7/22E - page 10

    Operation GENERAL I A WARNING A WARNING Before leaving the operator’s area for any reason, stop the engine and remove the key. Disconnect the spark plug wire and secure it away from the plug to prevent accidental start-up of the snowthrower. Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is hot 1 f ...

  • Simplicity 7/22E - page 11

    Operation 7. As the engine warms up and begins to operate even- ly, turn the choke knob slowly counterclockwise to the OFF position. If engine falters, return to l/2 choke position until it runs smoothly, then turn it to the choke OFF position. NOTE: Allow the engine to warm up for a few minutes before operating the snowthrower. Engine will not dev ...

  • Simplicity 7/22E - page 12

    Regular Maintenance NORMAL CARE I Every 25 Care Reauired See Paae Hours -a Check auger gear case lubrication.* Page 8 . I Lubricate snowthrower. Paae9 I . 1 Check tire pressure. I Paae 9 I l I 1 Change engine oil.**+ Clean or replace spark plug.+ . I I . i I Check discharge control. 1 Page 14 I I * I * The transmission and auger gear case have been ...

  • Simplicity 7/22E - page 13

    Regular- Maintenance LUBRICATION CHECKING TIRE PRESSURE A CAUTION It is very important that grease fittings on auger shaft (figure 6) are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break. With an oil can, apply medium weight (IOW) oil to points A & i3 shown in figure 7. There are two grease ...

  • Simplicity 7/22E - page 14

    A WARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent acciden- tal starting, disconnect the spark plug wire and fasten away from the plug. This section provides troubleshooting and service instructions. For problems not covered here, contact your dealer. T ...

  • Simplicity 7/22E - page 15

    SHIFT CONTROL ADJUSTMENT If any of the following conditions exist, it will be neces- sary to adjust the shift control. l Snowthrower is not in neutral when shift lever is in NEUTRAL position. l Reverse position cannot be fully reached. l 3rd gear cannot be fully reached. Adjust as follows: 1. Locate neutral position of shift lever by moving unit ba ...

  • Simplicity 7/22E - page 16

    Adjusting Drive Belts If the auger or wheels slip under load, belts could be stretched or worn. Adjust as follows: 1. Remove the belt cover (figure 10). Determine which belt requires adjustment. 2. Loosen the locknut on the appropriate idler pulley and move the idler pulley i/4” toward the belt (figure 11). Tighten the locknut. 3. Re-install the ...

  • Simplicity 7/22E - page 17

    A CAUTION Place a block (approximately 4” high) under front edge of auger housing or snowthrower will not stand on end. 6. See figure 13. Loosen nuts holding lower belt guard and slide guard away from belt. 7. Remove belt from between large pulleys. 13. Slide new belt onto pulley and position lower belt guard to within l/16” - i/8” of large d ...

  • Simplicity 7/22E - page 18

    WHEEL AXLE BEARING REPLACEMENT After approximately 100 hours of use (about 5 years), or if drive chain jumps off sprockets, wheel axle bearings may need to be replaced. 1. Disconnect spark plug wire and fasten it away from the spark plug. 2. Place a block under the snowthrower so the wheels are just off the ground. 3. See figure 16. Remove the ring ...

  • Simplicity 7/22E - page 19

    Specifications ENGINE Make ................................................................ Tecumseh Cylinders.. ..................................................................... .1 Cycles ............................................................................. 4 Crankshaft ....................................................... Horizontal ...

  • Simplicity 7/22E - page 20

    Replacement Parts %I Accessories COMMON REPLACEMENT PARTS Listed below are part numbers for the more common replacement parts. Use only genuine Simplicity replace- ment parts to assure optimum performance and safety. Special Worm Gear Oil for Auger Gear Case - 8 oz. Container.. .............................................. .1704636 - Case of 8 oz. ...

Produzent Simplicity Kategorie Snow Blower

Dokumente, die wir vom Produzenten des Geräts Simplicity 7/22E erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Simplicity
- Bedienungsanleitungen 7/22E
- Produktkarten Simplicity
- Informationsbroschüren
- oder Energieetiketten Simplicity 7/22E
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Simplicity 7/22E.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Simplicity 7/22E, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Simplicity 7/22E. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Simplicity 7/22E ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Simplicity 7/22E, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Simplicity 7/22E hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Simplicity 7/22E verständlich ist.

Eine gänzliche Bedienungsanleitung von Simplicity sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Simplicity 7/22E bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Simplicity 7/22E befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Simplicity 7/22E, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Simplicity 7/22E - die uns die ersten Schritte während der Nutzung von Simplicity 7/22E erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Simplicity 7/22E hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Simplicity 7/22E im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Simplicity 7/22E?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Simplicity 7/22E nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Simplicity 7/22E hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)