Bedienungsanleitung Ohlins FG 012

16 Seiten 1.01 mb
Download

Zur Seite of 16

Summary
  • Ohlins FG 012 - page 1

    1 Owners manual Öhlins motocr oss fr ont forks FG 012 GasGas Including: Setting up your bike Fine-tuning Service the fork General handling set-up T echnical info Spare par ts & tools ...

  • Ohlins FG 012 - page 2

    2 Contents Safety signals ............................. 2 Introduction ................................ 3 Design ....................................... 3 Before you start ......................... 3 Marking ...................................... 3 Recommended settings ............. 3 Mounting instructions ................. 4 Setting up the bike .. ...

  • Ohlins FG 012 - page 3

    3 cated at the bottom of the fork leg, fig 1, the rebound adjuster at the top, fig 2. Spring preload is adjusted with washers, fig 3, and optional springs ar e available to suit differ ent tracks and riders. In the legs ther e are also “air - springs“ (the air trapped above the oil) that work together with the “real“ spring. Y ou adjust the ...

  • Ohlins FG 012 - page 4

    4 F Spring pr eload is adjusted with spacers, see “Preload adjustment“ on page 8. Maximum allowed spring pr eload is 13 mm. If you need to pr eload the springs more than 13 mm, we r ecommend you to change to a “stiffer“ spring. Checking r ear static sag A Put your bike on a stand. Arrange the stand so that the rear wheel is of f the ground ...

  • Ohlins FG 012 - page 5

    5 Checking front ride height A Put your bike on a stand. Arrange the stand so that the fr ont wheel is off the gr ound and the fr ont fork fully extended. Measure the distance between the up- per fork crown and the fr ont wheel axle, fig 4 distance A. Make a note of the measurement. B Race dressed sit on the bike, straight above the foot pegs, with ...

  • Ohlins FG 012 - page 6

    6 CAUTION! Adjust the oil level with the fork leg fully compressed and no preload washer nor spring installed. NOTE! See mounting instruction for rec- ommended oil level. The oil level is measured fr om the top of the outer leg, with the top nut off, see fig 6. A change in oil level should be made in small steps. W e recommend a change of 5 mm at a ...

  • Ohlins FG 012 - page 7

    7 General handling set-up A Front end falls into the curves (over - steering) especially in sand. Steep front fork angle. Fr ont end too low in comparison to rear end.  Increas the fr ont fork compression damping.  Change to harder springs.  Lower fork leg approximately 5 mm in the triple clamp. B Front end ”ploughs”, understeers. Shal ...

  • Ohlins FG 012 - page 8

    8 Preload adjustment 1 Put the bike on a stand and loosen the screws in the fork top cr own that hold the fork legs. NOTE! On most MX-bikes you have to take of the handle bar before you can unscrew the top cap. Unscrew the top cap, use a 24 mm wrench. 2 Put a box under the front wheel so that the springs are visible. Remove the top cap from the dam ...

  • Ohlins FG 012 - page 9

    9 Changing springs 4 Loosen the screws that hold the fork legs in the upper fork crown. With the fork leg still tightened in the lower fork crown unscr ew the top cap, use a 24 mm wrench. Loosen the scr ews that hold the fork legs in the lower fork cr own. Remove the fork legs from the motorcycle. 5 Fasten the fork leg with soft jaws in a vice and ...

  • Ohlins FG 012 - page 10

    10 Dismantling 10 Perform steps 4-7 "Changing springs" on page 9. Loosen the bush head, on top of the cartridge tube, with tool 1797-01. Lift up the damper rod assembly and drain the oil. Pull up the scraper with a scr ew- driver , release and remove the cir clip. 11 CAUTION! The fork legs have two fixed and one sliding bushing. Be very c ...

  • Ohlins FG 012 - page 11

    11 13 Remove the seals and bushings and check them for wear and damage. Replace if necessary . CAUTION! When removing the oil seal and bushings use a small plastic bag to cover the bushing attachment groove and edges of the inner tube, to avoid damage to the seals. 14 Fasten the damper rod assembly with soft jaws in a vice. Remove all parts fr om t ...

  • Ohlins FG 012 - page 12

    12 Notes 19 Fasten the fork leg, at the fork bottom, with soft jaws in a vice. Install the compression valve as- sembly in the fork bottom. Tightening torque 65 Nm. Apply some front fork oil on the outer surface of the inner leg, and push the outer leg up and down a few times. Measure the corr ect amount of oil accor ding to the specification card. ...

  • Ohlins FG 012 - page 13

    13 T echnical specifications Fork lengths and diameters Front fork Motorcycle Length (L) ØA ØB FG 012 GasGas 938 mm 53,9 mm 58,4mm Rebound and compression adjustment Refer to mounting instruction for set-up data. Maximum open rebound and compr ession valve: 20 clicks. Free Spring Length: All forks: 467 mm (service limit 460 mm). Spring preload: M ...

  • Ohlins FG 012 - page 14

    14 Spare parts Pos. Part No. Pcs. DescriptionT ype/remarks 1 02338-01 2 Nut 2 02306-02 2 T op cap 3 00438-17 2 O-ring 4 02337-01 2 Spring support 5 02319-01 Pr eload washer see spec. car d 6 02328-39 2 Spring front fork 3,9 N/mm 02328-41 2 4,1 N/mm 02328-43 2 4,3 N/mm 02328-45 2 4,5 N/mm 02328-47 2 4,7 N/mm 7 02324-01 2 Fork leg outer 8 00329-02 2 ...

  • Ohlins FG 012 - page 15

    15 Spar e parts Pos. Part No. Pcs. Description T ype/remarks 1 02338-01 2 Lock nut 2 01050-01 2 Screw 3 00338-59 2 O-ring 4 02306-02 2 T op cap 5 01473-02 2 Circlip 6 00338-53 2 O-ring 7 02321-02 1 Adjustment screw 8 01248-01 2 Spring 9 00884-04 4 Ball 10 02366-12 2 Adjustment rod 11 00338-76 2 O-ring 12 02301-03 2 Needle housing 13 02302-03 2 Guid ...

  • Ohlins FG 012 - page 16

    16 07295-08 T eknisk Illustration AB, OM Motocr oss front fork FG 012 GasGas, 02 02. 200 ex. Mor e info www .ohlins.com The ultimate suspension site. Find out everything about your suspension. Download mounting instructions, manuals and br ochur es. And a lot mor e. Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby , Sweden Phone +46 8 590 025 0 ...

Produzent Ohlins Kategorie Bicycle

Dokumente, die wir vom Produzenten des Geräts Ohlins FG 012 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Ohlins
- Bedienungsanleitungen FG 012
- Produktkarten Ohlins
- Informationsbroschüren
- oder Energieetiketten Ohlins FG 012
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Ohlins FG 012.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Ohlins FG 012, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Ohlins FG 012. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Ohlins FG 012 ansehen.

Die komplette Bedienungsanleitung des Geräts Ohlins FG 012, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Ohlins FG 012 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Ohlins FG 012 verständlich ist.

Eine gänzliche Bedienungsanleitung von Ohlins sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Ohlins FG 012 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Ohlins FG 012 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Ohlins FG 012, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Ohlins FG 012 - die uns die ersten Schritte während der Nutzung von Ohlins FG 012 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Ohlins FG 012 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Ohlins FG 012 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Ohlins FG 012?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ohlins FG 012 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ohlins FG 012 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)