-
Icom ic pw1 - page 1
INSTR UCTION MANU AL iPW1 HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER ...
-
Icom ic pw1 - page 2
R W ARNING HIGH V OL T A GE! NEVER attach an antenna or internal antenna connector during trans- mission. This ma y result in an electrical shock or b ur n. R W ARNING! NEVER carr y the linear amplifier by yourself . At least two persons must carry the linear amplifier since it weights appro x. 25 kg (55 lb). R W ARNING! NEVER apply AC v oltage u ...
-
Icom ic pw1 - page 3
IMPORT ANT ...................................................... i PRECA UTIONS ................................................. i EXPLICIT DEFINITIONS .................................. ii T ABLE OF CONTENTS .................................... ii UNP A CKING ..................................................... ii 1 P ANEL DESCRIPTION ......... ...
-
Icom ic pw1 - page 4
1 1 P ANEL DESCRIPTION ■ Fr ont panel and remote controller 0 100 250 500 1K 1 .5K 0 TEMP ALC ALC ad j SWR 0 1 1.5 2 3 10 20 30 40 50 60 V D HOT I D Po 10 20 30 40 50 60 W A METER-1 METER-2 P o TEMP I D V D ALC SWR DOWN 1 .8 3 .5 7 1 0 1 4 1 8 21 24 28 50 UP ANT INPUT AUTO TRANSMIT TUNER AMP/ PROTECT POWER V ∞ 1 2 1 2 3 4 HF/ 50MHz ALL BAND 1kW ...
-
Icom ic pw1 - page 5
2 1 P ANEL DESCRIPTION q PO WER SWITCH [PO WER] (p . 11) Push momentarily to tur n power ON. w TRANSMIT INDICA T OR [TRANSMIT] (p . 13) Lights green while transmitting. During transmission, a humming may sound de- pending on the output power . This is caused by the large current produced by the po wer supply and does not indicate equipment malfunct ...
-
Icom ic pw1 - page 6
q OUTPUT ANTENNA CONNECT ORS [ANT1] – [ANT4] (p . 6) Accept a 50 Ω antenna with a PL-259 connector . w A CCESSOR Y SOCKET -1 [A CC-1] A CCESSOR Y SOCKET -2 [A CC-2] Enable connection to Icom e xciters (transceivers). - See the page at right for soc ket inf or mation. - The [ACC-2] sock et is connected in parallel with [A CC-1] by def ault and c ...
-
Icom ic pw1 - page 7
4 1 P ANEL DESCRIPTION D A CC-1 SOCKET D A CC-2 SOCKET (w/[EXCITER] is “ 1 ” ) The f ollowing descriptions are applied when the [EXCITER] s witch is set to “ 1 ” (default). When [EX- CITER] is set to “ 1&2, ” [ACC-2] functions the same as [A CC-1] abov e for the 2nd e xciter . ACC-1 PIN NO. PIN NAME DESCRIPTION SPECIFICATIONS 1 8 V ...
-
Icom ic pw1 - page 8
5 2 INST ALLA TION AND CONNECTIONS (1) Single-phase 3-wire line (200 – 240 V A C) q The green wire from the A C power cab le must be connected to the protective earth. w The blac k and white wires from the A C power cable can be connected to either terminal. *Use the appropriate AC plug if required. (2) Single-phase 2-wire line (100 – 120 V A C ...
-
Icom ic pw1 - page 9
■ Gr ounding T o pre v ent electr ical shock, tele vision interference (TVI), broadcast interference (BCI) and other prob- lems, g round the linear ampli fi er through the GROUND terminal on the rear panel. F or best results, connect a heavy gauge wire or str ap to a long ear th-sunk copper rod. Make the distance be- tween the GR OUND ter minal ...
-
Icom ic pw1 - page 10
■ System inter connections 1 or 2 Icom 100 W HF transceiv ers can be connected as e xciters to the IC-PW1. Non-Icom transceivers can be used, how ev er , band selection will not be synchro- nized f or each exciter . See the f ollo wing diag r ams f or making connections be- tween the IC-PW1 and an e xciter (transceiv er). See p . 5 f or AC po wer ...
-
Icom ic pw1 - page 11
8 2 INST ALLA TION AND CONNECTIONS • Using 2 Icom exciter s (transceivers) The f ollowing connections also apply to trans- ceiv ers having multiple antenna connectors f or speci fi ed bands (e.g. IC-726, IC-729, etc.) IC-PW1 IC-756 Ground Coaxial cable (supplied) OPK-5 (optional) ACC cable (supplied) Remote control cable (supplied) To an antenna ...
-
Icom ic pw1 - page 12
9 2 INST ALLA TION AND CONNECTIONS • Using 1 Icom and 1 non-Icom exciter s (transceivers) NO TE: The speci fi cations f or the SEND relay are 5 V DC 0.1 A. If this le vel is e xceeded, a large e x- ternal relay must be used. • Using non-Icom exciter s (transceivers) when the IC-PW1 ’ s power is OFF T o use the antenna selector of the IC-PW1 ...
-
Icom ic pw1 - page 13
10 2 INST ALLA TION AND CONNECTIONS The control section of the linear ampli fi er can be sep- arated from the main body , doubling as a remote con- troller . It can be placed on the e xciter or in another conv enient place. q Disconnect the A C power cab le. w Remov e 8 screws from the sides of the linear am- pli fi er , then lift up the top cove ...
-
Icom ic pw1 - page 14
■ Setting the ALC levels Bef ore fi rst applying power , make sure all connections required f or your system are complete b y referring to chapter 2. Then, reset the linear amplifier using the f ollowing procedure. NO TE: Resetting CLEARS all programmed set- tings to def ault values . q Make sure the linear ampli fi er , e xciter and auxiliar y ...
-
Icom ic pw1 - page 15
12 3 OPERA TION The IC-PW1 uses CI-V frequency data f or automatic selection of the operating band. Program the e xciter ’ s address to use this capability as f ollows: F or non-Icom exciters , the IC-PW1 cannot be con- trolled using the CI-V function, so this setting is not necessar y . F or transceivers which ha v e multiple antenna con- nector ...
-
Icom ic pw1 - page 16
13 3 OPERA TION CA UTION: DO NO T operate the IC-PW1 before adjusting the ALC le vels properly with the [ALC adj1] and [ALC adj2] pots. (p . 11) It takes 15 sec. f or CI-V line initial settings when se veral CI-V de vices (more than 5) are connected to a CI-V line. For IC-781 users with other Icom CI-V transceiver s: T urn the IC-781 power ON bef o ...
-
Icom ic pw1 - page 17
3 OPERA TION 14 This linear ampli fi er has v ar ious protection circuits. D ALC circuit The ALC (A utomatic Lev el Control) circuit automati- cally limits RF output power b y controlling the input le vel of the e xciter . This prev ents transmission of dis- tor ted signals when the input signal lev el e xceeds the allow able le vel. The ALC activ ...
-
Icom ic pw1 - page 18
4 MAINTENANCE 15 PROBLEM POSSIBLE CAUSE SOLUTION REF. Power does not come on when the [POWER] switch is pushed. • Cable connection is faulty. • The circuit breaker is turned OFF. • Check the connection and connection cable pins. • Check for the cause, then turn the circuit breaker ON. pgs. 7 – 9 p. 3 Sensitivity is low. • The antenna is ...
-
Icom ic pw1 - page 19
5 SPECIFICA TIONS 16 ■ General • F requency cover age: 0 1.800 – 0 1.999 MHz 0 3.500 – 1 3.999 MHz 0 7.000 – 1 7.300 MHz 10.100 – 10.150 MHz 14.000 – 14.350 MHz 18.068 – 18.168 MHz 21.000 – 21.450 MHz 24.890 – 24.990 MHz * 1 28.000 – 29.700 MHz * 1 50.000 – 54.000 MHz * 1 The U .S.A. v ersion can only be used the antenna tun ...
-
Icom ic pw1 - page 20
6-9-16 Kamihigashi, Hirano-ku, Osaka 547-0002 J apan A-5449G-1EX- w Printed in Japan © 1997 Icom Inc. Count on us! ...
Haben Sie eine Frage bezüglich Icom ic pw1?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Icom ic pw1 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Icom ic pw1 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.