Bedienungsanleitung Graco Hydra-Clean 800-094

15 Seiten 1.27 mb
Download

Zur Seite of 15

Summary
  • Graco Hydra-Clean 800-094 - page 1

    This manual contains IMPORTANT READ AND RETAlN FOR REFERENCE WARNINGS and INSTRUCTIONS Q P/N 800-093 SERIES "A" - CART MODEL P/N 800-094 SERIES "A" - HANDLE MODEL 800 psi (55 bar) OPERATING PRESSURE 1 100 psi (76 bar) MAXIMUM WORKING PRESSURE ...

  • Graco Hydra-Clean 800-094 - page 2

    UNJECTUON HAZARD Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious injury. including the need for amputation. NEVER point the spray gun at anyone or any part of the body. NEVER put hand or fingers over the spray tip. NEVER try to stop or deflect leaks with your hand or body. ' ' MEDICAL TREA ...

  • Graco Hydra-Clean 800-094 - page 3

    .. . . .. ~. j CART MOTOR CONTROL POWER COR0 HANDLE MODEL ADJUSTABLE NOZZLE CONTROL RING 3/4" GARDEN HOSE THREAD SPRAYTIP H6") 4 PRESSURE 4 HIGH PRESSURE AOJUSTMENT HOSE I30 FT.) KNOB Check For Damage Check unit for any damage that may have occurred in shipping. Any damage should be noted and the carrier notified immediately. Check unit&a ...

  • Graco Hydra-Clean 800-094 - page 4

    Connect To Water Supply -CAUTION plumbing codes regarding cross-connection to water supply. Optional backflowpreventorP/N 801-1 33 is available to prevent the back-up of Do not exceed 1 GOOF (70'C) water temperature to pump in a direct supply system. from your city water supply to the units 3/d inch Connect a hose with at least 3/4 inch (19 mm ...

  • Graco Hydra-Clean 800-094 - page 5

    Turn control ring on adjustable nozzle clockwise to cause a drop in pressure. Start pressure washer unit and trigger spray gun. The. injector may draw momentarily as system is filling but actuate injector, turn chemical adjustment knob out. normally will stop as system builds up to full pressure. To counterclockwise. until chemical begins to be dra ...

  • Graco Hydra-Clean 800-094 - page 6

    SERVICE Troubleshooting PROBLEM Low.Pressure rump runs extremely rough, pressure low. iNater leakage from under :he manifold. iNater in pump crankcase. Zrequent or premature 'ailure of the packing. jtrong surging at the inlet Ind low pressure on the lischarge side. hit will not start. :hemica1 injection system oesn't work. r leaks. pray g ...

  • Graco Hydra-Clean 800-094 - page 7

    ... . : .. .. ,. BARBS DRAWING Pressure Washer A 33. WIRING DIAGRAM 801-888 7 ...

  • Graco Hydra-Clean 800-094 - page 8

    PARTS LIST Pressure Washer Assembly, 800-093. 800-094 REF. PART NO. NO. 800-093 800-094 i 800.154 2 800.157 4 801-931 3 801-859 5 801-929 6 801-966 7 801-930 8 801-893 10 801.884 9 801.884 11 801-226 12 801-304 13 801-221 14 801-894 15 801-605 16 801-606 17 801-875 19 801-882 18 801.876 21 801-967 20 *EO1 -883, 22 801.677 23 801-683 24 801-129 25 8 ...

  • Graco Hydra-Clean 800-094 - page 9

    PARTS DRAWING Pump/Motcr Asse PARTS LIST Pump/Motor Assembly, 800-1 54 REF. PART NO. NO. DESCRIPTION QTY DESCRIPTION QTY 1 801-862 MOTOR, 1.5 hp, "C Face .NO. NO. 1 2 801-864 PUMP, T-9791, see parts 16 801-023 WASHER, Flat, 1/4 4 17 801-139 WASHER, Lock. 1/4 drawing, page 11 4 3 801-870 COUPLER HOUSING 1 1 18 801.546 BOLT, Hex Hd., 3/8-16x 1-1 ...

  • Graco Hydra-Clean 800-094 - page 10

    SERVICE Pump (Refer to Parts Drawing, Page 11) MOTE: Three sizes of metric wrenches are M17, and M6 Allen wrench. necessary for servicing the. pump; M30, Valves: 1. Remove the hex plug (5) from manifold (6) using M30 wrench. 2. Examineo-ring(4)underplugandreplace'ifcutsor distortion exist. '3. Remove valve~unit and O-ring (3) from cavity. ...

  • Graco Hydra-Clean 800-094 - page 11

    PARTS DRAWING Pump, 8pl-864 " **PACKING & RETAINER KIT 801 -664 Includes: 'PLUNGER REPAIR REF. NO. QTY. 9 1 NO. KIT 801-474 Includes: REF. 'PACKING KIT *OIL SEAL KIT *VALVE UNIT KIT QTY. 10 1 15 3 801-662 11 1 16 3 12 1 NO. REF. 17 13 3 1 801-658 801 -472 REF. QTV. REF. NO. QTV. NO. 14 3 3 an. Includes: Includes: Includes: 18 3 1 ...

  • Graco Hydra-Clean 800-094 - page 12

    SERVICE Chemical injector The nozzle, check valve, valve seat, and needle valve may be cleaned by disassembling the chemical injector if clogging occurs within. or if downstream restriction increases in any As with any injector, if the spray tip becomes clogged manner, the injector will stop drawing chemical: The restriction should be eliminated be ...

  • Graco Hydra-Clean 800-094 - page 13

    ! NOTE: Hose. Swivel & Spray Tip are not included with Gun Assembly - See Pressure Washer Assembly Pans Drawing/List. page 7. 8. Gun Assembly, 800-1 57 SERVICE Gun, Cartridge Replacement 1. Press access pin (1 2) from gun handle and remove access plate (14) by sliding plate backwards. Remove cartridge (5) from housing (6) by using a 19 mm socke ...

  • Graco Hydra-Clean 800-094 - page 14

    ACCESSORIES (Must be purchased separately) CHEMICAL CLEANING COMPOUNDS: General Purpose Cleaner 800-1 06 Vehicle Wash 800-108 Heavy Duty Degreaser 800-1 07 supply. install upstream from pump. Metal Pretreatment, Phosphatizer 800-109 Paintable Rust Inhibitor 800- 1 10 BACK FLOW PREVENTOR 801 -1 33 Prevent back-up of contaminated water into fresh TEC ...

  • Graco Hydra-Clean 800-094 - page 15

    THE GRACQ WARRANTY Graco Inc. warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship under normal use and service. This warranty extends to the original purchaser for a perid of 12 months from the date of purchase and applies only when the equipment is installed and operated in accordance ...

Produzent Graco Kategorie Pressure Washer

Dokumente, die wir vom Produzenten des Geräts Graco Hydra-Clean 800-094 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Graco
- Bedienungsanleitungen Hydra-Clean 800-094
- Produktkarten Graco
- Informationsbroschüren
- oder Energieetiketten Graco Hydra-Clean 800-094
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Graco Hydra-Clean 800-094.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Graco Hydra-Clean 800-094, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Graco Hydra-Clean 800-094. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Graco Hydra-Clean 800-094 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Graco Hydra-Clean 800-094, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Graco Hydra-Clean 800-094 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Graco Hydra-Clean 800-094 verständlich ist.

Eine gänzliche Bedienungsanleitung von Graco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Graco Hydra-Clean 800-094 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Graco Hydra-Clean 800-094 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Graco Hydra-Clean 800-094, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Graco Hydra-Clean 800-094 - die uns die ersten Schritte während der Nutzung von Graco Hydra-Clean 800-094 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Graco Hydra-Clean 800-094 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Graco Hydra-Clean 800-094 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Graco Hydra-Clean 800-094?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Graco Hydra-Clean 800-094 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Graco Hydra-Clean 800-094 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)