Bedienungsanleitung Humminbird TCR ID-10

19 Seiten 0.15 mb
Download

Zur Seite of 19

Summary
  • Humminbird TCR ID-10 - page 1

    ...

  • Humminbird TCR ID-10 - page 2

    TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefully consider the f ollowing before installing your transducer. TRANSDUCER MOUNTING OPTIONS A. Transom Mount - The Humminbird hig ...

  • Humminbird TCR ID-10 - page 3

    by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it back in place. (See Figure A) B. Inside Hull Mount - The high speed transducer can be mounted inside the hull (without pivot assembly) using the proper two - part epox ...

  • Humminbird TCR ID-10 - page 4

    Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the center of the Bracket slots. On some alu minum boats it may be necessary to use a wood back - up plate. It is important to use a silicone sealant betwe ...

  • Humminbird TCR ID-10 - page 5

    NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water level. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied. Be sure to align the holes so that they are c ...

  • Humminbird TCR ID-10 - page 6

    Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the headed pin and in sert it through the two parts. Assemble by screwing the ¼”x3/8” allen head screw into the end of the pin a ...

  • Humminbird TCR ID-10 - page 7

    wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly fastened to the pivot . (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the bottom of the transom. ( ...

  • Humminbird TCR ID-10 - page 8

    7. Remove the water and transducer and clean the marked area and t he bottom of the transducer thoroughly. 8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted. The puddle should be larger than the bottom of the tran sducer. 9. Coat the bot ...

  • Humminbird TCR ID-10 - page 9

    Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilted to any desired position. ...

  • Humminbird TCR ID-10 - page 10

    OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommend ed since the unit cannot be rotated. INSTALLING THE CABLES Your LCR comes equipped with Humminbird’s n ...

  • Humminbird TCR ID-10 - page 11

    It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”. Note: An adapter (AD - 4) is available to allow use of an old waterproof (BNC) transducer with the LCR, but be sure that the transducer is a 16degree ...

  • Humminbird TCR ID-10 - page 12

    ...

  • Humminbird TCR ID-10 - page 13

    Specifications: Operating Frequency 200 KHz Power Requirement 12 volts Power Cable Length 111/2' Transducer (standard) XHS-6-16 high-speed Transducer Cone Angle 16 degrees Transducer Cable Length 20' Depth Ranges 0-15', 0-30', 0-60', 0-120', 0-180', 0-240', 0-360', 0-480' Zoom Ranges 7', 15&apo ...

  • Humminbird TCR ID-10 - page 14

    NOTE: The built - in simulator will allow y ou to practice adjusting the sensitivity, but your adjustments will not change readings being displayed on the screen. READING THE TCR ID - 10 SCREEN Your TCR has a liquid crystal display, or LCD. The liquid crystal material in the display aligns itself to either block light or let light pass through. Thi ...

  • Humminbird TCR ID-10 - page 15

    60' scale and it changes to the 0 - 30' scale, the entir e screen will look as if you had been in the 0 - 30' range all along. 2. Using zoom and bottom - lock. Through Pixel Memory Capacity, the memory in the TCR ID - 10 stores readings in much finer detail than is displayed in the "regular mode. So when you activate t he zoom o ...

  • Humminbird TCR ID-10 - page 16

    Of course, the best way t o learn to read your TCR ID - 10 is to use it, especially in familiar locations. If you know what's underwater and can see it displayed on the screen, then you're on your way to being an experienced TCR user. ...

  • Humminbird TCR ID-10 - page 17

    OPERATING THE TCR ID - 10 Your new TCR ID - 10 offers unique automatic features, as well as many adjustable ones. If you're learning to operate the TCR ID - 10 with its simulator, follow the directions listed at "Built - In Simulator" on page 16, and then come back to this page. If you're learnin g to use your TCR ID10 using act ...

  • Humminbird TCR ID-10 - page 18

    The following describes the functions and how to use them, in order of appearance after you turn the unit on. 1. Sensitivity Automatic setting: on, "O" or normal As conditions change, the computer will automatically increase or decrease the sensitivity setting. You can manually increase or decrease the automatic setting from a range of &q ...

  • Humminbird TCR ID-10 - page 19

    buttons, you can move the zoom window while the zoom is activated, without having to press Select again. 5. Bottom - Lock Automatic setting: off You can easily turn on the bottom - lock with the On/Off button. When on, this function shows up - close zoom r eadings in reference to the bottom. The size of the zoom window depends on the depth range - ...

Produzent Humminbird Kategorie Fish Finder

Dokumente, die wir vom Produzenten des Geräts Humminbird TCR ID-10 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Humminbird
- Bedienungsanleitungen TCR ID-10
- Produktkarten Humminbird
- Informationsbroschüren
- oder Energieetiketten Humminbird TCR ID-10
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Humminbird TCR ID-10.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Humminbird TCR ID-10, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Humminbird TCR ID-10. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Humminbird TCR ID-10 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Humminbird TCR ID-10, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Humminbird TCR ID-10 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Humminbird TCR ID-10 verständlich ist.

Eine gänzliche Bedienungsanleitung von Humminbird sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Humminbird TCR ID-10 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Humminbird TCR ID-10 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Humminbird TCR ID-10, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Humminbird TCR ID-10 - die uns die ersten Schritte während der Nutzung von Humminbird TCR ID-10 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Humminbird TCR ID-10 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Humminbird TCR ID-10 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Humminbird TCR ID-10?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Humminbird TCR ID-10 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Humminbird TCR ID-10 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)