Bedienungsanleitung Chromalox 8003

19 Seiten 0.24 mb
Download

Zur Seite of 19

Summary
  • Chromalox 8003 - page 1

    8003 Issue Date April 1994 ❒ USER’S MANUAL 0037 -75212 1/8 DIN Temperature Controller 8003 Cover 4/27/06, 2:26 PM 1 ...

  • Chromalox 8003 - page 2

    Chromalox 8003 User's Manual i Contents Model Identification ........................................................................................................... ......................... Page ii Dimensions and Panel Cutout .................................................................................................... ............. ...

  • Chromalox 8003 - page 3

    ii Chromalox 8003 User's Manual Model Identification Model 8003 1/8 DIN Temperature Controller Code Output 1 - Heat or Cool 1 SPDT Relay, 3 Amps at 250 Vac (Resistive) or SSR Drive, 14V @ 20mA, Jumper Selectable Code Output 2 - Cool or Alarm 1 Relay, 2 Amps at 250 Vac (Resistive) or SSR Drive, 14V @ 20mA, Jumper Selectable Code Options 0 None ...

  • Chromalox 8003 - page 4

    Chromalox 8003 User's Manual 1 Dimensions in inches (mm in parenthesis) Chromalox SMRT PV MAIN AL1 AL2 SMRT FUNC COOL HB SP 0.5 (12.8) 3.5 (89) 1.9 (48) 3.8 (96) 1.77 (45) 3.62 (92) 5.1 (125) 2.4 (60) 8003 Manual 4/27/06, 2:24 PM 1 ...

  • Chromalox 8003 - page 5

    2 Chromalox 8003 User's Manual Warnings: • When a relay output is used to drive an inductive load, it is suggested that you connect an external snubber network (RC) across the terminals in accordance with the following table (or use Chromalox snubber P/N 0149-01305): • Do not run sensor input wires together with power cables. • For therm ...

  • Chromalox 8003 - page 6

    Chromalox 8003 User's Manual 3 Hardware Setup To select the output type(s) and the alarm contact settings: 1. Remove the instrument from its case. 2. Move the jumpers to the desired position as shown in the diagram. 3. Set J304 and J305 as shown in the following figure. PZ22 PZ21 PZ20 PZ19 PZ18 PZ17 PZ16 PZ15 PZ14 PZ13 PZ12 1 1 J305 (MAIN outp ...

  • Chromalox 8003 - page 7

    4 Chromalox 8003 User's Manual General Operation There are two setup modes for the 8003: • Configuration Mode • Operator Mode In general, the Configuration Mode is the initial setup of the controller when first installed. Input type and alarm setup are examples of Configuration Mode settings. The Operator Mode includes settings that might ...

  • Chromalox 8003 - page 8

    Chromalox 8003 User's Manual 5 P1 = Input Type and Standard Range Range 0 = TC type L 0 / +800 ° C 1 = TC type J 0 / +800 ° C 2 = TC type K 0 / +999 ° C 3 = TC type N 0 / +999 ° C 4 = RTD type Pt 100 -199 / +500 ° C 5 = RTD type Pt 100 -19.9 / +99.9 ° C 8 = TC type L 0 / +999 ° F 9 = TC type J 0 / +999 ° F 10 = TC type K 0 / +999 ° F ...

  • Chromalox 8003 - page 9

    6 Chromalox 8003 User's Manual P9 = Alarm 1 Inhibit Available only when P7 is different from 0. OFF = inhibit disabled ON = inhibit enabled Note : The Alarm Inhibit disables the alarm action after a setpoint change. At startup, it automatically enables the alarm when the process temperature reaches the present condition. P10 = Alarm 2 Type 0 = ...

  • Chromalox 8003 - page 10

    Chromalox 8003 User's Manual 7 P15 = Threshold of the “Soft Start” Function Enter the threshold value, in ° F or ° C, for the automatic start of the "Soft Start" function (output power limit). The range of this setting is determined by the range of the sensor selected in P1 (i.e., if type J T/C ° F is selected in P1, range is ...

  • Chromalox 8003 - page 11

    8 Chromalox 8003 User's Manual P22 = Alarm 2 Relay Action This parameter is available only if P10 is different from 0 and P16 is different from OFF. r = Reverse (relay de-energized in alarm condition) d = Direct (relay energized in alarm condition) P23 = Automatic Adjustment of "Relative Cooling Gain" OFF = the SMART function does no ...

  • Chromalox 8003 - page 12

    Chromalox 8003 User's Manual 9 SMART Function SMART automatically determines the best PID control parameters for your application. To enable the SMART function, push the SMRT pushbutton. The SMRT LED will light or flash according to the algorithm automatically selected. When the SMART function is enabled, it is possible to display, but not to ...

  • Chromalox 8003 - page 13

    10 Chromalox 8003 User's Manual The upper display will show the measured value while the lower display will show the programmed setpoint value (we define this status as “normal display mode”). Pushbutton functionality during operating mode : FUNC = Stores the new value of a selected parameter and increments to the next parameter. SMRT = Sc ...

  • Chromalox 8003 - page 14

    Chromalox 8003 User's Manual 11 td Derivative (rate), range 1 second to 9 minutes and 59 seconds. If 0, derivative is disabled. C Heating cycle time, range 1 to 200 seconds (30 seconds or greater recommended for relay outputs). C2 Cycle Time for Output 2 (heat/cool control selected), range 1 to 200 seconds (30 seconds or greater recommended fo ...

  • Chromalox 8003 - page 15

    12 Chromalox 8003 User's Manual Error Messages Overrange or Underrange Indications The instrument shows the OVERRANGE conditions with the following indication on the upper display: The instrument shows the UNDERRANGE conditions with the following indication on the upper display: Burn-out conditions are shown as well as overrange condition. For ...

  • Chromalox 8003 - page 16

    Chromalox 8003 User's Manual 13 Error Messages The instrument has a self-diagnostic algorithm. When an error is detected, the instrument shows “Err” indication on the lower display while the upper display shows the code of the detected error. Error List 100 Write EEPROM error. 150 CPU error. 200 Write on protected memory. 201-2xx Configura ...

  • Chromalox 8003 - page 17

    14 Chromalox 8003 User's Manual Warranty And Limitation Of Remedy And Reliability Chromalox warrants only that the Products and parts manufactured by Chromalox, when shipped, and the work performed by Chromalox when performed, will meet all applicable specification and other specific product and work requirements (including those of performanc ...

  • Chromalox 8003 - page 18

    Chromalox 8003 User's Manual 15 submit a claim as provided above shall specifically waive all claims for damages or other relief, including but not limited to claims based on latent defects. In no event shall buyer be entitled to incidental or consequential damages and buyer should hold Chromalox harmless therefrom. Any action by buyer arising ...

  • Chromalox 8003 - page 19

    Chromalox ® INSTRUMENTS AND CONTROLS 1382 HE I L Q UAKE R BO U LE V AR D LA V E RG N E, TN 37086-353 6 PHO N E (6 15) 793-3900 FAX (6 15) 7 93-35 6 3 8003 Back Cover 4/27/06, 2:25 PM 1 ...

Produzent Chromalox Kategorie Air Conditioner

Dokumente, die wir vom Produzenten des Geräts Chromalox 8003 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Chromalox
- Bedienungsanleitungen 8003
- Produktkarten Chromalox
- Informationsbroschüren
- oder Energieetiketten Chromalox 8003
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Chromalox 8003.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Chromalox 8003, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Chromalox 8003. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Chromalox 8003 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Chromalox 8003, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Chromalox 8003 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Chromalox 8003 verständlich ist.

Eine gänzliche Bedienungsanleitung von Chromalox sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Chromalox 8003 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Chromalox 8003 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Chromalox 8003, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Chromalox 8003 - die uns die ersten Schritte während der Nutzung von Chromalox 8003 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Chromalox 8003 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Chromalox 8003 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Chromalox 8003?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Chromalox 8003 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Chromalox 8003 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)