Deutsch dropdown-ico

Bedienungsanleitung Snapper 555

32 Seiten 2.05 mb
Download

Zur Seite of 32

Summary
  • Snapper 555 - page 1

    OPERA T OR’S MANU AL Intermediate Sno wthr o wer Models 555 Models Mfg. No. Description 1694587 555M, 5HP Snowthrower, Manual Start 1694595 555M, 5HP Snowthrower, Manual Start (Export) 85665 I5225, 5HP Snowthrower, Manual Start 80494 EI5225, 5HP Snowthrower, Manual Start (Export) 860 Models Mfg. No. Description 85666 I8245E, 8HP OHV Snowthrower, ...

  • Snapper 555 - page 2

    1 T able of Contents Safety Rules & Inf ormation Training ...................................................................2 Preparation .............................................................2 Operation ................................................................2 Children ........................................................... ...

  • Snapper 555 - page 3

    2 This machine is capable of amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. ...

  • Snapper 555 - page 4

    3 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service. 10. Maintain or replace safety and instruction labels as necessary. 11. Keep nuts and bolts tigh ...

  • Snapper 555 - page 5

    4 ...

  • Snapper 555 - page 6

    5 Identification Numbers When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access. These numbers can be found in the locations shown. NOTE: For location ...

  • Snapper 555 - page 7

    6 Safety Decals T raction Disengage T raction Engage Free Hand Unlocked Free Hand Locked AVOID SERIOUS INJUR Y OR DEATH • Read the operator's manual for operating and safety instructions. • Do not defeat the safety features of control. They are for your protection. • Keep machine properly maintained and serviced with all shields, guards, ...

  • Snapper 555 - page 8

    Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. 7 CE Safety Icons & Compliance Specs Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing. Remove the key, disconnect spark plug wire, and consult technic ...

  • Snapper 555 - page 9

    8 Features, Controls, & Operation TECUMSEH MODELS BRIGGS & STRA TT ON MODELS Please take a moment and familiarize yourself with the name, location, and function of these controls so that you will better understand the safety and operating instructions provided in this manual. 1 ,2.. ALL MODELS ...

  • Snapper 555 - page 10

    9 Features & Controls Fuel Fuel tank filler cap (see illustration). Note: The fuel shut off valve is located under the fuel tank. Close the valve when the snowthrower is not in use. Open the valve before starting. Starter Handle Used to pull-start the engine. Primer Button Primes carburetor for faster cold starting. Throttle Le ver Controls eng ...

  • Snapper 555 - page 11

    10 Engine Controls ST AR TING CONTROLS See Figures 1 & 2 for the following instructions. Units with Optional Electric Start A. Electric Start Button - The electric start button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter han- dle. The electric start button operates on 120 Volts AC, which is ...

  • Snapper 555 - page 12

    11 Controls Figure 3. Operator's Control Position A. Speed Selector C. Auger Control B. Drive Control D. Chute Direction Control Figure 4. Snowthrower Controls A. Speed Selector E. Chute Deflector B. Drive Control F. Chute Deflector Knob C. Auger Control G. Skid Shoes D. Chute Control Knob H. Traction Lock Pins A B C D A D B E F G H C GR OUND ...

  • Snapper 555 - page 13

    12 Operation GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out tool is attached to the handle on the machine. Do not oper- ate the machine without the clean-out tool properly stored on the handle. 3. Check the engine oil le ...

  • Snapper 555 - page 14

    13 Operation ST AR TING THE ENGINE 1. Turn the fuel valve (B, Figure 5 & 6) to the ON posi- tion. 2. Insert the engine key (F) into the engine key slot and push fully in to the RUN position. 3. Move the throttle lever (E) fully up to the FAST posi- tion. 4. Fully close the choke (G) if engine is cold. (Do not choke a warm engine.) 5. Push the p ...

  • Snapper 555 - page 15

    14 Operation OPERA TING THE SNO WTHRO WER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger control (C, Figure 7) on the right-hand grip to begin auger rotation. To dis- engage the auger, completely release the lever. 4. Fully press and hold the traction ...

  • Snapper 555 - page 16

    15 Operation DEFLECT OR The distance of the discharged snow is mainly controlled by the position of the deflector (Figure 9). (Engine speed also affects distance of discharge. Always operate at FULL throttle.) The more the deflector is tilted UP, the farther snow will be thrown. Loosen the deflector knob, tilt the deflector UP or DOWN, and then ret ...

  • Snapper 555 - page 17

    16 Operation Figure 11. Traction Drive Lock - Disengaged FREE-WHEELING AND TRA CTION DRIVE LOCK For easy turning when pushing the snowthrower, you can disengage the traction drive at one or both wheels by using the traction lock pins (See Figures 11 & 12). 1. Turn the unit off, remove the engine key, and discon- nect the spark plug wire. 2. To ...

  • Snapper 555 - page 18

    17 Regular Maintenance CHECK A UGER GEAR CASE LUBRICA TION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (Figure 14). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add The Dealer Line Winter Weight Worm Gear Oil (available from your dealer). 4. Re-install pipe plug, and tigh ...

  • Snapper 555 - page 19

    18 Maintenance Figure 15. Drive Area Lubrication Points (Bottom Cover Removed) A. Drive Disc C. Hex Shaft B. Friction Disc Figure 16. Snowthrower General Lubrication Points A B C Remove wheels and grease axles once each year. There are two grease fittings on the auger shaft. Wipe the fittings clean and apply grease, using a grease gun. Also apply g ...

  • Snapper 555 - page 20

    19 Storage LUBRICA TION CHECK / LUBRICA TE FREE-HAND LINKA GE Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released. If the controls do not function properly, lubricate them. If lubrication does no ...

  • Snapper 555 - page 21

    T roubleshooting, Adjustment, & Service 20 PROBLEM POSSIBLE CA USE REMED Y Engine fails to start. 1. Key is OFF. 2. Failure to prime cold engine 3. Fuel valve is in CLOSED position. 4. Out of fuel. 5. Choke OFF - cold engine. 6. Engine flooded. 7. Spark plug not sparking. 8. Water in fuel, or old fuel. 1. Push key in to the ON position. 2. Pres ...

  • Snapper 555 - page 22

    21 T roubleshooting PROBLEM POSSIBLE CA USE REMED Y Auger rotates, but snow is not thrown far enough 1. Chute deflector too low. 2. Engine speed too slow. 3. Ground speed too fast. 4. Snowthrower discharge chute clogged. 5. Auger belt loose or worn. 1. Adjust deflector as necessary. 2. Set speed to full throttle. 3. Use slower speed selector settin ...

  • Snapper 555 - page 23

    22 Adjustments SPEED SELECT OR PIV O T ADJUSTMENT The speed selector is factory set for optimal performance at each forward and reverse speed setting. However, if drive system components have been replaced, adjust- ment may be necessary. Adjust as follows: 1. Move the ground speed control (A, Figure 19) fully forward. 2. Loosen the hardware (B) sec ...

  • Snapper 555 - page 24

    23 Adjustments MANU AL DISCHARGE CHUTE CONTR OL LINKA GE ADJUSTMENT Pinion Gear Adjustment If the discharge chute is difficult to operate, first lubricate the pinion gear (A, Figure 21) and ring gear (F). If it is still difficult to operate, adjust as follows: NOTE: If the discharge chute will not stay in position, adjust the pinion gear (A) closer ...

  • Snapper 555 - page 25

    24 Adjustments Figure 23. Auger Drive Clutch Cable Adjustment Auger Drive Clutch Cable Auger Drive Clutch Cable Spring Adjustment Hex Nut A UGER DRIVE CLUTCH CABLE ADJUSTMENT The auger drive clutch cable should be adjusted so that there is no slack in the cable when moved slightly from side to side. To adjust tension on the cable: 1. Loosen adjustm ...

  • Snapper 555 - page 26

    25 Adjustments DRIVE BEL T ADJUSTMENT (Continued) If the auger drive slips (auger slows or doesn't rotate nor- mally while blowing snow), or stays engaged when the control is disengaged — and the auger clutch cable has been properly adjusted — the auger drive belt may be out of adjustment. Checking A uger Belt & Belt Guide Adjustments ...

  • Snapper 555 - page 27

    26 Adjustments & Service DRIVE BEL T ADJUSTMENT (Continued) Adjusting A uger Belt Guide 1. With the auger control still fully depressed, adjust the auger belt guide so that there is a 1/64” gap (1/32” Maximum) between the end of the guide and the belt (Figure 28), making certain the guide is NOT putting pressure on the belt. 2. Making certa ...

  • Snapper 555 - page 28

    27 Service DRIVE BEL T REPLA CEMENT (Cont.) A uger Drive Belt Replacement 1. Remove gas from fuel tank and run engine until it stops running from lack of fuel. 2. Disconnect spark plug wire and fasten it away from the spark plug. 3. Remove belt cover (See Figure 25). 4. Loosen auger belt guide and slide belt off engine pul- ley and away from idler ...

  • Snapper 555 - page 29

    28 Service SHEAR PIN REPLA CEMENT Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break. (This protects the gear box and other parts from damage.) The shear pins are located on the auger shaft as shown in Figure 32. To replace the shear pins, tap out broken pin with a pin punch, and ...

  • Snapper 555 - page 30

    29 Specifications ENGINE: 5 HP* T ecumseh Make Tecumseh Model Snow King Horsepower 5 HP @ 3600 rpm Displacement 11.88 Cu. in (195 cc) Oil Capacity See Engine Owner’s Manual 8 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Snow Horsepower 8 HP @ 3600 rpm Displacement 18.6 Cu. in (305 cc) Oil Capacity 28 oz. (,84 L) CHASSIS: Wheel ...

  • Snapper 555 - page 31

    30 Replacement Parts & Accessories REPLA CEMENT P ARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. TECHNICAL MANU ALS Additional copies of this manual are available, as well as fully illustrated parts lists. These manuals show all of the product’s components in exploded v ...

  • Snapper 555 - page 32

    MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004, Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...

Produzent Snapper Kategorie Snow Blower

Dokumente, die wir vom Produzenten des Geräts Snapper 555 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Snapper
- Bedienungsanleitungen 555
- Produktkarten Snapper
- Informationsbroschüren
- oder Energieetiketten Snapper 555
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Snapper 555.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Snapper 555, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Snapper 555. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Snapper 555 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Snapper 555, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Snapper 555 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Snapper 555 verständlich ist.

Eine gänzliche Bedienungsanleitung von Snapper sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Snapper 555 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Snapper 555 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Snapper 555, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Snapper 555 - die uns die ersten Schritte während der Nutzung von Snapper 555 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Snapper 555 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Snapper 555 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Snapper 555?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Snapper 555 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Snapper 555 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)