Deutsch dropdown-ico

Bedienungsanleitung Snapper 7555

32 Seiten 2.96 mb
Download

Zur Seite of 32

Summary
  • Snapper 7555 - page 1

    () Bimplicilq ® SNAPPER TM OPERATOR'S MANUAl / Intermediate Snowthrower Models 555 Models Mfg. No. Description 1694587 555M, 5HP, Manual Start 1694595 555M, 5HP, Manual Start (CE) 85665 15225, 5HP, Manual Start 80494 EI5225, 5HP, Manual Start (CE) 7555 Models Mfg. No. Description 1694836 7555M, 7.5HP, Manual Start 1694837 7555EX, 7.5HP, Manua ...

  • Snapper 7555 - page 2

    Table of Contents Safety Rules & Information Training ................................................................... 2 Preparation ............................................................. 2 Operation ................................................................ 2 Children ............................................................ ...

  • Snapper 7555 - page 3

    Safety Rules & Information TRAINING 1. Read, understand, and follow all instructions on the machine and in the manuals before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate the equipment. Never all ...

  • Snapper 7555 - page 4

    Safety Rules 21. Keep in mind the operator is responsible for acci- dents occurring to other people or property. 22. Data indicates that operators, age 60 years and above, are involved in a large percentage of power equipment-related injuries. These operators should evaluate their ability to operate the unit safely enough to protect themselves and ...

  • Snapper 7555 - page 5

    ...

  • Snapper 7555 - page 6

    Identifinatinn NumberS North American / CE Models CE Models (only) ID Tag Location Identification Numbers I'J;[o]wlg£_lll ;l=ld=l;l=l_[H=l 1=7_,111r_,q When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer's identi- fication numbers ...

  • Snapper 7555 - page 7

    Safety Decals GENERAL This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and safety instructions it contains will provide you with the necessary basic knowl- edge to operate this equipment safely ...

  • Snapper 7555 - page 8

    CF Safety Ir.nns & Cnmnliance SpecS Warning: Read Operator's Manual. Read and understand the Operator's Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Dismemberment. This machine can amputate limbs. Keep bystanders and children away when ...

  • Snapper 7555 - page 9

    Features, Controls, & Operation Please take a moment and familiarize yourself with the name, location, and function of these controls so that you will better understand the safety and operating instructions provided in this manual ALL MODELS TECUMSEH MODELS BRIGGS & STRATTON MODELS ...

  • Snapper 7555 - page 10

    Features & Controls CONTROL LOCATIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls appfied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section. _1_ Speed Selector S ...

  • Snapper 7555 - page 11

    Engine Controls STARTING CONTROLS See Figures 1 & 2 for the following instructions. Units with Optional Electric Start A. Electric Start Button (North American Models)- The electric start button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter handle. The electric start button oper- ates on 120 V ...

  • Snapper 7555 - page 12

    Cnntrnls GROUND SPEED CONTROLS A. Speed Selector - This lever (A, Figures 3 & 4) is used to set the ground speed of the snowthrower. The snowthrower has five forward speeds, 1-5, and two reverse speeds, 1-2. No neutral position or gate is required, since the traction drive design automati- cally provides "neutral" (no forward or rever ...

  • Snapper 7555 - page 13

    Operation GENERAL OPERATION CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out tool is attached to the handle on the machine. Do not oper- ate the machine without the clean-out tool properly stored on the handle. 3. Check the engine oil level. Se ...

  • Snapper 7555 - page 14

    STARTING THE ENGINE 1. Turn the fuel valve (B, Figure 5 & 6) to the ON posi- tion. 2. Insert the engine key (F) into the engine key slot and push fully in to the RUN position. 3. Move the throttle lever (E) fully up to the FAST posi- tion. 4. Fully close the choke (G) if engine is cold. (Do not choke a warm engine.) 5. Push the primer button (D ...

  • Snapper 7555 - page 15

    Operation OPERATING THE SNOWTHROWER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger control (C, Figure 7) on the right-hand grip to begin auger rotation. To dis- engage the auger, completely release the lever. 4. Fully press and hold the traction drive ...

  • Snapper 7555 - page 16

    DEFLECTOR The distance of the discharged snow is mainly controlled by the position of the deflector (Figure 9). (Engine speed also affects distance of discharge. Always operate at FULL throttle.) The more the deflector is tilted UP, the farther snow will be thrown. Loosen the deflector knob, tilt the deflector UP or DOWN, and then retighten the kno ...

  • Snapper 7555 - page 17

    Operation FREE-WHEELING AND TRACTION DRIVE LOCK For easy turning when pushing the snowthrower, you can disengage the traction drive at one or both wheels by using the traction lock pins (See Figures 11 & 12). 1. Turn the unit off, remove the engine key, and discon- nect the spark plug wire. 2. To DISENGAGE the traction drive lock, insert the tr ...

  • Snapper 7555 - page 18

    Regular Maintenance MAINTENANCE SCHEDULE MAINTENANCE REQUIRED FREQUENCY NOTES Check auger gear case lubrication.** Lubricate snowth rower. Check tire pressure. Change engine oil.*+ Clean or replace spark plug.+ Check drive linkage/belt tension. Lubricate Axle Shafts. Check/Lubricate Free-Hand Linkage. Lubricate Auger Shaft. *** * Change original oi ...

  • Snapper 7555 - page 19

    Maintenance LUBRICATION IMPORTANT NOTE It is very important that grease fittings on the auger shaft are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break. To prevent wheels rusting to axles, it is also necessary to remove the wheels and grease the axles regularly. Remove wheels and grease axles ...

  • Snapper 7555 - page 20

    Stnrage LUBRICATION CHECK / LUBRICATE FREE-HAND LINKAGE Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released. If the controls do not function properly, lubricate them. If lubrication does not rect ...

  • Snapper 7555 - page 21

    Troubleshooting, Adjustment, & Service TROUBLESHOOTING This section provides troubleshooting and service instructions. Locate the problem and check the possible cause/remedy in the order listed. Also, refer to the engine manufacturer's Owner's Manual for additional information. For problems not covered here, contact your local deal- e ...

  • Snapper 7555 - page 22

    Troubleshooting REMEDY PROBLEM Auger rotates, but snow is not thrown far enough POSSIBLE CAUSE 1. Chute deflector too low. 2. Engine speed too slow. 3. Ground speed too fast. 4. Snowthrower discharge chute clogged. 5. Auger belt loose or worn. 1. Adjust deflector as necessary. 2. Set speed to full throttle. 3. Use slower speed selector setting. 4. ...

  • Snapper 7555 - page 23

    Adjustments SPEED SELECTOR PIVOT ADJUSTMENT The speed selector is factory set for optimal performance at each forward and reverse speed setting. However, if drive system components have been replaced, adjust- ment may be necessary. Adjust as follows: 1. Move the ground speed control (A, Figure 19) fully forward. 2. Loosen the hardware (B) securing ...

  • Snapper 7555 - page 24

    MANUAL DISCHARGE CHUTE CONTROL LINKAGE ADJUSTMENT Pinion Gear Adjustment If the discharge chute is difficult to operate, first lubricate the pinion gear (A, Figure 21) and ring gear (F). If it is still difficult to operate, adjust as follows: NOTE: If the discharge chute will not stay in position, adjust the pinion gear (,4) closer to the ring gear ...

  • Snapper 7555 - page 25

    Adjustments AUGER DRIVE CLUTCH CABLE ADJUSTMENT The auger drive clutch cable should be adjusted so that there is no slack in the cable when moved slightly from side to side. To adjust tension on the cable: 1. Loosen adjustment hex nut (Figure 23) by holding the adjusting flats and turning adjustment hex nut. 2. Tighten adjustment screw by turning a ...

  • Snapper 7555 - page 26

    Ad_iustmP.nts DRIVE BELT ADJUSTMENT (Continued) If the auger drive slips (auger slows or doesn't rotate nor- mally while blowing snow), or stays engaged when the control is disengaged -- and the auger clutch cable has been properly adjusted -- the auger drive belt may be out of adjustment. WARNING Auger must NOT rotate unless the Auger Control ...

  • Snapper 7555 - page 27

    Adjustments & Service DRIVE BELT ADJUSTMENT (Continued) Adjusting Auger Belt Guide 1 With the auger control still fully depressed, adjust the auger belt guide(s) so that there is a 1/64" gap (1/32" Maximum) between the guide and the belt (Figures 28, 28a), making certain the guide is NOT putting pressure on the belt. 2. Making certain ...

  • Snapper 7555 - page 28

    DRIVE BELT REPLACEMENT (Cont.) Traction Drive Belt Replacement (Cont.) 5. Reverse the procedure to install the new belt. Be sure there are no twists in the belt, and that the belt is properly seated in the pulley grooves. 6. Replace the belt cover. 7. Start the unit, and check the traction drive for proper operation. See "Traction Clutch Cable ...

  • Snapper 7555 - page 29

    Service ROLLER CHAIN REPLACEMENT NOTE: This procedure does not apply to models that use an "endless" chain. 1. Remove gas from fuel tank and run engine until it stops running from lack of fuel. 2. Disconnect spark plug wire and fasten it away from the spark plug. 3. Tilt the snowthrower forward and carefully rest unit on the auger end. 4. ...

  • Snapper 7555 - page 30

    Specifications NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors. ENGINE: CHASSIS: Wheels 5 HP* Tecumseh Spout Rotation Make Tecumseh Impeller Model Snow King Drive System Horsepower 5 HP @ ...

  • Snapper 7555 - page 31

    Replacement Parts& Accessories REPLACEMENT PARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. MAINTENANCE ITEMS Many convenient and helpful service and maintenance items are available from your authorized dealer. Some of these items include: Engine Oil Touch-Up Paint Grease ...

  • Snapper 7555 - page 32

    MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, Wl 53074-0997 www.simplicitymfg.com © Copyright 2005, Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...

Produzent Snapper Kategorie Snow Blower

Dokumente, die wir vom Produzenten des Geräts Snapper 7555 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Snapper
- Bedienungsanleitungen 7555
- Produktkarten Snapper
- Informationsbroschüren
- oder Energieetiketten Snapper 7555
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Snapper 7555.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Snapper 7555, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Snapper 7555. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Snapper 7555 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Snapper 7555, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Snapper 7555 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Snapper 7555 verständlich ist.

Eine gänzliche Bedienungsanleitung von Snapper sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Snapper 7555 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Snapper 7555 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Snapper 7555, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Snapper 7555 - die uns die ersten Schritte während der Nutzung von Snapper 7555 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Snapper 7555 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Snapper 7555 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Snapper 7555?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Snapper 7555 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Snapper 7555 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)