Bedienungsanleitung Troy-Bilt CSV206

14 Seiten 3.15 mb
Download

Zur Seite of 14

Summary
  • Troy-Bilt CSV206 - page 1

    Chipper Shredder Vacuum Oper ator’ s Man ual IMPOR T ANT : Read saf ety rules and instructions carefully TRO Y -BIL T LLC P .O . BOX 361131 CLEVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal co mbustion engine and should not be used on or nea r any unimproved forest-covered, brush - covered or grass-covered land unless th ...

  • Troy-Bilt CSV206 - page 2

    2 TABLE OF CONTENTS Content Page Important Safe Operation Practic es .. ................ ................ ............. ................ ....... 3 Assembling Your Chipper Shredder Va cuum ................ ................ ............. .......... 5 Know Your Chipper Shr edder Vacuum .......................... ................ ................ ..... ...

  • Troy-Bilt CSV206 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES Training 1. Read, understand, and follow all instructi ons on the machine and in the manual(s) before attempti ng to assemble and ope rate. Keep this manual in a safe place for future and regular re ference and for o rdering replacement parts. 2. Be familiar with all controls and their proper operatio ...

  • Troy-Bilt CSV206 - page 4

    4 2. Before starting th e machine, make sure the ch ipper chute, feed intake, and cutting cham ber are empty and free of all debris. 3. Thoroughly inspect al l material to be shredde d and remove any metal, rocks, bott les, cans, or other foreign objects which could cause personal injury or damage to the machine. 4. If the impeller strikes a foreig ...

  • Troy-Bilt CSV206 - page 5

    5 SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER VACUUM Unpacking • Remove staple s, break glue on top flaps, or cut tape at carton end an d peel along top flap to open carton. • Remove loose parts if included with unit (i. e., operator’s manu al, etc.) • Cut along cor ners, lay carton down f lat, and remove packing material. • Roll or slide ...

  • Troy-Bilt CSV206 - page 6

    6 • Remove the thre e hex nuts and bell washers from the weld studs beside the op ening on the right side of the chipper-shred der vacuum. See Figure 4. Figure 4 • Place the chipper chute over the weld studs keeping the slotted sid e towards the bottom. Loosely secure with the three hex nu ts and bell washers that were removed earlier. Do not f ...

  • Troy-Bilt CSV206 - page 7

    7 SECTION 3: KNOW YOUR CHIPPER SHREDDER VACUUM m Figure 7 Vacuum/Chipper Bag Collects shredded or chipped mat erial fed through the chipper chute or vacuumed up through the nozzle. See Figure 7. Chipper Chute Allow twigs and small bran ches up to 3” in diameter to be fed into the imp eller for chipping. See Figure 7. Tamper Plug This plug is inse ...

  • Troy-Bilt CSV206 - page 8

    8 SECTION 4: OPERATING YOUR CHIPPER SHREDDER VACUUM • Read, under stand, and follow all instructio ns and warnings on the machine an d in this manual before operating. A pair of safety glasses has bee n provided with this equipm ent. Gas & Oil Fill-Up Service the eng ine with gasoline and oil a s instructed in the engine manual. Re ad instruc ...

  • Troy-Bilt CSV206 - page 9

    9 SECTION 5: ADJUSTING YOUR CHIPPER SHREDDER VACUUM Front Caster Wheels This chipper shredder vacuum is equipped with front caster wheels. The casters can be locked in a straight ahead position or to swivel freely. • Lift and place pins in the larger holes for locked or straight ahead operation. See Figure 8. a. Place pins in smaller hole s to al ...

  • Troy-Bilt CSV206 - page 10

    10 SECTION 6: MAINTAINING YOUR CHIPPER SHREDDER VACUUM Lubrication • Wheels: Lubricate the rear wh eels with light oil once a season. • Nozzle Door Adju stment Le vers: Lubric ate each adjustment lever once a season with light oil. • Front Caste r Wheels: Grease fittings are located on the front caster whee ls to provide easy lubrication of t ...

  • Troy-Bilt CSV206 - page 11

    11 • When sharpening blades, follow the original angle of grind. Also, make sure to re move an equal amount fr om each blade a nd torque har dware to 250 - 300 in.lb. NOTE: Make sure th at blades are reassembled with the sharp edge facin g upward. Replacing the Belt NOTE: Because the engine on this equipment has a tapered crankshaft, a sp ecial i ...

  • Troy-Bilt CSV206 - page 12

    12 Figure 17 • Press down on the belt guard spri ng by the idler pulley, and release the sprin g from the slot on the idler bracket. • Place the belt on the idle r pulley and place belt guard spring back int o the slot on the idler bracket. See Figure 17. • Place the mounting adapter again st the engine and make sure the hole in the mounting ...

  • Troy-Bilt CSV206 - page 13

    13 SECTION 7: TROUBLESHOOTING NOTE: For repairs be yond the minor adjustments listed abov e, contact your nearest authorize d service dealer. Prob lem Cause Remedy Engine fails to start 1. Spark plug wire disconnected. 2. Fuel tank emp ty or stale fuel. 3. Throttle control lever not in corre ct starting posit ion. (If Equip ped) 4. Choke not in CHO ...

  • Troy-Bilt CSV206 - page 14

    MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States, its possessions an d territories. “Troy-Bilt” warrants this produc t against defects in material and workmanship for a pe riod of two (2) years commencing on the date ...

Produzent Troy-Bilt Kategorie Chipper

Dokumente, die wir vom Produzenten des Geräts Troy-Bilt CSV206 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Troy-Bilt
- Bedienungsanleitungen CSV206
- Produktkarten Troy-Bilt
- Informationsbroschüren
- oder Energieetiketten Troy-Bilt CSV206
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Troy-Bilt CSV206.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Troy-Bilt CSV206, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Troy-Bilt CSV206. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Troy-Bilt CSV206 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Troy-Bilt CSV206, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Troy-Bilt CSV206 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Troy-Bilt CSV206 verständlich ist.

Eine gänzliche Bedienungsanleitung von Troy-Bilt sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Troy-Bilt CSV206 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Troy-Bilt CSV206 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Troy-Bilt CSV206, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Troy-Bilt CSV206 - die uns die ersten Schritte während der Nutzung von Troy-Bilt CSV206 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Troy-Bilt CSV206 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Troy-Bilt CSV206 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Troy-Bilt CSV206?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Troy-Bilt CSV206 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Troy-Bilt CSV206 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)