Deutsch dropdown-ico

Bedienungsanleitung Cabletron Systems F3

44 Seiten 0.19 mb
Download

Zur Seite of 44

Summary
  • Cabletron Systems F3 - page 1

    FOT-F3 FIBER OPTIC TRANSCEIVER USER’S MANUAL ...

  • Cabletron Systems F3 - page 2

    ...

  • Cabletron Systems F3 - page 3

    FOT-F3 USER’S MANUAL i NO TICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is ...

  • Cabletron Systems F3 - page 4

    ii FOT-F3 USER’S MANUAL FCC NO TICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested ...

  • Cabletron Systems F3 - page 5

    FOT-F3 USER’S MANUAL iii VCCI NO TICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial and/or indust ...

  • Cabletron Systems F3 - page 6

    iv FOT-F3 USER’S MANUAL DECLARATION OF CONFORMITY Application of Council Directi ve(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial W ay PO Box 5005 Rochester , NH 03867 European Representativ e Name: Mr . J. Solari European Representativ e Address: Cabletron Systems Limited Nexus ...

  • Cabletron Systems F3 - page 7

    FOT-F3 USER’S MANUAL v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ...............................................................1-1 1.2 CONVENTIONS .........................................................................1-2 1.3 OVERVIEW OF THE FOT-F3 ....................................................1-2 1.3.1 Connections .......... ...

  • Cabletron Systems F3 - page 8

    CONTENTS vi FOT-F3 USER’S MANUAL CHAPTER 4 TESTING AND TROUBLESHOOTING 4.1 INSTALLATION CHECK-OUT ................................................... 4-1 4.1.1 Testing the Fiber Optic Link Segment ........................ 4-1 4.1.2 Testing the FOT-F3 Fiber Optic Transceiver ............. 4-3 4.2 USING LANVIEW ..................................... ...

  • Cabletron Systems F3 - page 9

    FOT-F3 USER’S MANUAL 1-1 CHAPTER 1 INTRODUCTION Welcome to Cabletron Systems FOT-F3 Fiber Optic Transceiver User’s Manual . This manual serves as a simple installation and reference guide for the FOT-F3 transceiver. You should have a general working knowledge of Ethernet or IEEE 802.3 type data communications networks and their physical layer c ...

  • Cabletron Systems F3 - page 10

    CHAPTER 1: INTRODUCTION 1-2 FOT-F3 USER’S MANUAL Chapter 4, T esting and T roubleshooting , contains procedures for verifying the proper installation of the FOT-F3. It also describes LANVIEW LEDs and their function. Appendix A, Specifications , provides the specifications for the FOT-F3 transceiver. 1.2 CONVENTIONS The following conventions are u ...

  • Cabletron Systems F3 - page 11

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-3 Figure 1-1 FOT-F3 1.3.1 Connections The FOT-F3 connects two active Ethernet devices using an AUI cable and a fiber optic link segment. Devices such as repeaters, multiport repeaters, multiport transceivers or host systems are connected using fiber optic cables. The FOT-F3 is fully compatible with IE ...

  • Cabletron Systems F3 - page 12

    CHAPTER 1: INTRODUCTION 1-4 FOT-F3 USER’S MANUAL A fiber optic cable is connected to the transceiver through ST fiber optic ports on the FOT-F3. This provides an optical link to connect the device to the network. 1.3.2 Distance and Cable T ype The FOT-F3 supports single mode fiber optic cable for sizes such as 8.3/125 µ m, 8.7/125 µ m, 9/125 µ ...

  • Cabletron Systems F3 - page 13

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-5 The SQE test signal is generated after the FOT-F3 has transmitted a data packet. This signal is generated only between the FOT-F3 and the device; it is not transmitted onto the network. Note: Do not enable the SQE test feature when the FOT-F3 is attached to a repeater or Ethernet Version 1 equipment ...

  • Cabletron Systems F3 - page 14

    CHAPTER 1: INTRODUCTION 1-6 FOT-F3 USER’S MANUAL PWR (Power) When on, this green LED indicates that the FOT-F3 is receiving power. SQE (Signal Quality Error) Test Function When on, this yellow LED indicates that SQE is enabled. XMT (Transmit) This green LED flashes to indicate that the FOT-F3 is transmitting frames onto the network. RCV (Receive) ...

  • Cabletron Systems F3 - page 15

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-7 1.3.4 Application The FOT-F3 can be configured into your network in many ways. For example, in Figure 1-3, a fiber optic link segment (4) is attached to a Cabletron Systems Multi Media Access Center (MMAC) (5) with a FOMIM-32/36/38. The MMAC serves as an intelligent repeater hub that links the fiber ...

  • Cabletron Systems F3 - page 16

    CHAPTER 1: INTRODUCTION 1-8 FOT-F3 USER’S MANUAL In another example, shown in Figure 1-4, a FOT-F3 (3) is connected to an MMAC (1) by an AUI cable (2) attached to an Intelligent Repeater Module (IRM) in the MMAC. A lengthy fiber optic link segment (4) of up to five kilometers runs from the FOT-F3 (3) to another FOT-F3 (5). The hardware connection ...

  • Cabletron Systems F3 - page 17

    GETTING HELP FOT-F3 USER’S MANUAL 1-9 1.4 GETTING HELP If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support: By phone (603) 332-9400 Monday – Friday; 8 A.M . – 8 P.M . Eastern Time By CompuServe GO CTRON from any ! prom ...

  • Cabletron Systems F3 - page 18

    CHAPTER 1: INTRODUCTION 1-10 FOT-F3 USER’S MANUAL • The device history (i.e., have you returned the device before, is this a recurring problem, etc.) • Any previous Return Material Authorization (RMA) numbers 1.5 RELATED MANUALS Use the manuals identified below to supplement the procedures and other technical data provided in this manual. The ...

  • Cabletron Systems F3 - page 19

    FOT-F3 USER’S MANUAL 2-1 CHAPTER 2 INST ALLA TION REQUIREMENTS Before installing the FOT-F3 Fiber Optic Transceiver, all conditions, guidelines, specifications, and requirements included in this chapter and Appendix A must be met to ensure satisfactory performance from the FOT-F3. Failure to follow these guidelines may result in unsatisfactory ne ...

  • Cabletron Systems F3 - page 20

    CHAPTER 2: INSTALLATION REQUIREMENTS 2-2 FOT-F3 USER’S MANUAL • When determining the maximum fiber optic cable length, the fiber optic budget and total netw or k propagation dela y should be calculated and taken into consider ation before fiber runs are incor porated into any network design. Fiber optic budget is the combination of the optic ...

  • Cabletron Systems F3 - page 21

    FOT-F3 USER’S MANUAL 3-1 CHAPTER 3 INST ALLA TION This chapter contains instructions for unpacking the FOT-F3 Transceiver, connecting the FOT-F3 to an Ethernet device and the network, surface mounting the transceiver (if necessary), and cable support installation. Verify that all the requirements listed in Chapter 2, Installation Requirements , a ...

  • Cabletron Systems F3 - page 22

    CHAPTER 3: INSTALLATION 3-2 FOT-F3 USER’S MANUAL If you notice any discrepancies, contact Cabletron Systems Technical Support immediately. Refer to Chapter 1, Getting Help , for instructions. 3.2 CONNECTING THE FOT-F3 TO THE NETWORK After you are sure that all the requirements listed in Chapter 2, Installation Requirements , and Appendix A, Speci ...

  • Cabletron Systems F3 - page 23

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-3 Figure 3-1 SQE Switch 3.2.2 Connecting the A UI Cable To connect your Ethernet device to the FOT-F3, attach an AUI cable as follows. See Figure 3-2. 1. Attach an A UI cable to the de vice to which the FO T -F3 will be connected. O T -F3 SQE P W R S Q E X M T R C V C L N L N K TX SQE SW ...

  • Cabletron Systems F3 - page 24

    CHAPTER 3: INSTALLATION 3-4 FOT-F3 USER’S MANUAL 2. Attach the f emale connector on the A UI cable to the A UI por t on the FO T -F3. If the power is on f or the Ether net de vice, the PWR LED should be lit, indicating the transceiv er is receiving power from the de vice. Also, if the SQE test is enabled, the SQE LED should be lit. Figure 3-2 AUI ...

  • Cabletron Systems F3 - page 25

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-5 c. Disconnect the device to which the transceiver is attached. d. Check the AUI connections for proper pinouts. The pinouts for the transceiver connection are listed in Appendix A. e. Check the cable for continuity. f. Reconnect the AUI cable to the FOT-F3 and the device. 3. Mov e the ...

  • Cabletron Systems F3 - page 26

    CHAPTER 3: INSTALLATION 3-6 FOT-F3 USER’S MANUAL ST connectors attach to ST ports much like BNC connectors attach to BNC ports. See Figure 3-3. The connector is inserted into the port with an alignment key on the connector inserted into the alignment slot on the port. The connector is then turned to lock it down. Caution: Do not touch the ends of ...

  • Cabletron Systems F3 - page 27

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-7 Figure 3-3 ST Connectors 6. Check that the LNK LED on the FO T -F3 is on. If the LED is off , perform each of the follo wing steps until the LED is on: a. Check that the power is on for the device at the other end of the link. b. Verify that the fiber strands are properly connected to ...

  • Cabletron Systems F3 - page 28

    CHAPTER 3: INSTALLATION 3-8 FOT-F3 USER’S MANUAL If a link is not established, contact Cabletron Systems Technical Support. Refer to Chapter 1, Getting Help , for instructions. 3.3 SURFACE MOUNTING THE FOT-F3 Using the contents of the accessory package, you can mount the FOT-F3 on a surface close to the workstation or on the workstation itself. T ...

  • Cabletron Systems F3 - page 29

    CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL 3-9 3.4 CABLE SUPPORT INSTALLATION Relieve the strain from the cables attached to the FOT-F3, whether or not the transceiver is mounted to a surface such as a wall. Note: Be sure each cable is securely attached to its port and that the slide latch on the AUI connector is secured to the lock posts on ...

  • Cabletron Systems F3 - page 30

    CHAPTER 3: INSTALLATION 3-10 FOT-F3 USER’S MANUAL Figure 3-4 Surface Mounting the FOT-F3 3.4.2 Cable Strain Relief f or Non-Mounted FO T -F3 To relieve the strain to cables connected to a FOT-F3 that is not surface mounted, proceed as follows: 1. If possible , use long tie wraps to secure the FO T -F3 to a structural suppor t such as a beam or a ...

  • Cabletron Systems F3 - page 31

    CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL 3-11 The FOT-F3 is now ready for operation. We recommend that you test the system prior to transmitting data. Refer to Chapter 4, Testing And Troubleshooting , for information about how to test the system. ...

  • Cabletron Systems F3 - page 32

    CHAPTER 3: INSTALLATION 3-12 FOT-F3 USER’S MANUAL ...

  • Cabletron Systems F3 - page 33

    FOT-F3 USER’S MANUAL 4-1 CHAPTER 4 TESTING AND TROUBLESHOO TING This chapter lists procedures to test the FOT-F3 after it is connected to the network. A description of LANVIEW and its function in troubleshooting physical layer network problems is also provided. 4.1 INSTALLATION CHECK-OUT This section contains procedures to test the following • ...

  • Cabletron Systems F3 - page 34

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-2 FOT-F3 USER’S MANUAL 4. F ollowing the instructions for the test set, test the jumpers to get a ref erence lev el. Make a note of this reading. 5. Disconnect the jumpers from the barrel connector . 6. Using the jumper , attach the optical power meter to one end of one strand of the link segment. 7. Using ...

  • Cabletron Systems F3 - page 35

    INSTALLATION CHECK-OUT FOT-F3 USER’S MANUAL 4-3 4.1.2 T esting the FO T -F3 Fiber Optic T ransceiver T wo Ethernet node testers capable of generating v alid data pack ets, such as the LAN-MD , are required for this procedure . Refer to Figure 4-1 and proceed as follows: 1. Using an AUI cable (2), connect a LAN-MD (1) to the FOT-F3 (3). Figure 4-1 ...

  • Cabletron Systems F3 - page 36

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-4 FOT-F3 USER’S MANUAL 2. Using another A UI cable (6), connect the other LAN-MD (7) to another FO T -F3 (5) attached to the same fiber optic link segment as the FO T -F3. 3. Select and run test 6 - SER VER on the LAN-MD connected in step 1. V er ify that this test passes. • The status on the LAN-MD sho ...

  • Cabletron Systems F3 - page 37

    USING LANVIEW FOT-F3 USER’S MANUAL 4-5 Figure 4-2 shows the location of the LANVIEW LEDs on the FOT-F3. This is followed by a description of how to interpret the indications of these LANVIEW LEDs. Figure 4-2 LANVIEW LEDs Optical Link OK (LNK) LED When on, this green LED indicates that a link has been established between the receive circuitry of t ...

  • Cabletron Systems F3 - page 38

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-6 FOT-F3 USER’S MANUAL Receive (RCV) LED This yellow LED flashes to indicate that the transceiver is receiving a frame from the network. The flash of the LED is pulse stretched for easy viewing. The LED flashes when traffic is on the network, even if the data is not intended for the device attached to the ...

  • Cabletron Systems F3 - page 39

    USING LANVIEW FOT-F3 USER’S MANUAL 4-7 Power (PWR) LED When on, this green LED indicates that the transceiver is receiving power from the device connected to the FOT-F3 AUI port. If this LED is off, power is not being received from the device or the DC-to-DC converter in the transceiver has failed. ...

  • Cabletron Systems F3 - page 40

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-8 FOT-F3 USER’S MANUAL ...

  • Cabletron Systems F3 - page 41

    FOT-F3 USER’S MANUAL A-1 APPENDIX A SPECIFICA TIONS This appendix contains the operational specifications for the FOT-F3. A.1 FIBER OPTIC INTERFACE The FOT-F3 has ST fiber optic ports. Table A-1 lists the parameters along with the associated typical, and minimum/ maximum specifications. Table A-1 Fiber Optic Interface Specifications Parameter Typ ...

  • Cabletron Systems F3 - page 42

    APPENDIX A: SPECIFICATIONS A-2 FOT-F3 USER’S MANUAL Parameter Typical Minimum Maximum Receive Sensitivity: -31.0 dBm -36.0 dBm -30.0 dBm Max. Receive Input Power: — — -14.0 dBm Transmitter Power at 25 ° C Into 8.3/125 µ m fiber: -18.0 dBm -21.0 dBm -15.0 dBm Output Power Coefficient: -0.07 dB/ ° C— — Notes: Transmitter Power decreases ...

  • Cabletron Systems F3 - page 43

    AUI CONNECTOR FOT-F3 USER’S MANUAL A-3 A.2 AUI CONNECTOR The AUI connector is a male DB15 receptacle with a metal shell for cable shielding. Refer to Figure A-1 for pinout identification. Figure A-1 AUI Connector Pinout Identification A.3 POWER SUPPLY Table A-2 provides the specifications of the power supply in the FOT-F3. Table A-2 Power Supply ...

  • Cabletron Systems F3 - page 44

    APPENDIX A: SPECIFICATIONS A-4 FOT-F3 USER’S MANUAL A.4 ENVIRONMENTAL Table A-3 provides the FOT-F3 environmental specifications. A.5 AGENCY APPROVALS Safety The FOT-F3 meets the safety requirements of UL1950, CSA C22.2 No. 950, EN 60950, and 73/23/EEC. Electromagnetic Compatibility The FOT-F3 meets the EMC requirements of FCC Part 15 Class A, EN ...

Produzent Cabletron Systems Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Cabletron Systems F3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cabletron Systems
- Bedienungsanleitungen F3
- Produktkarten Cabletron Systems
- Informationsbroschüren
- oder Energieetiketten Cabletron Systems F3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cabletron Systems F3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cabletron Systems F3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cabletron Systems F3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cabletron Systems F3 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cabletron Systems F3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cabletron Systems F3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cabletron Systems F3 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cabletron Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cabletron Systems F3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cabletron Systems F3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cabletron Systems F3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cabletron Systems F3 - die uns die ersten Schritte während der Nutzung von Cabletron Systems F3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cabletron Systems F3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cabletron Systems F3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cabletron Systems F3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cabletron Systems F3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cabletron Systems F3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)