Deutsch dropdown-ico

Bedienungsanleitung Dell 420

49 Seiten 2.54 mb
Download

Zur Seite of 49

Summary
  • Dell 420 - page 1

    DellPrecision™WorkStation420SystemsServiceManual Desktop Chassis — Removing and Replacing Parts Mini Tower Chassis — Removing and Replacing Parts NOTE: You can obtain the latest version of this document from the Support section of the Dell Web site at http://www.dell.com . Notes, Notices, and Cautions Throughout this guide, ...

  • Dell 420 - page 2

    Back to Contents Page Desktop Chassis — RemovingandReplacingParts:DellPrecision™WorkStation420 Systems Service Manual Overview This section provides procedures for removing and replacing the components, assemblies, and subassemblies in the Dell Precision WorkStation 420 desktop chassis system. Unless otherwise noted, eac ...

  • Dell 420 - page 3

    Restarting the System To restart the system and reset the chassis intrusion detector, perform the following steps: 1. Replace the computer cover and reconnect the computer and peripherals to their power sources and turn them on. ALERT! Cover was previously removed. 2. To reset the chassis intrusion detector, enter System Setup, select System Securi ...

  • Dell 420 - page 4

    To replace the computer cover, perform the following steps: 1. Check all cable connections, especially those that might have come loose during your work. Fold cables out of the way so that they do not catch on the computer cover. Make sure cables are not routed over the drive bracket — they will prevent the cover from closing properly. 2. Check t ...

  • Dell 420 - page 5

    Front - Panel Inserts Figure5.5.25 - Inch Front - Panel Insert Removal To remove a 5.25 - inch front - panel insert, perform the following steps: 1. Hold the inverted top cover with the front facing you. 2. From the front of the top cover, use your thumbs to press inward on the insert until it snaps free of the cover. To replace a 5.25 - i ...

  • Dell 420 - page 6

    Figure 7. AGP Pro50 Card Extension Figure 7 shows the card extension that may occupy PCI slots 1 and 2. The following is a list of valid expansion - card combinations: l One AGP card and five PCI cards l One AGP card, four PCI cards, and one RAID card l One AGP Pro50 card and four PCI cards l One AGP Pro50 card, three PCI cards, and one RAID card E ...

  • Dell 420 - page 7

    Expansion - Card Guide Figure 8. Expansion - Card Guide Removal To remove the expansion - card guide, perform the following steps: 1. Remove the hard - disk drive bracket . 2. Face the computer from the front. From the outside of the chassis, press in with your fingers on the two tabs on the left side of the expansion - card guide (see Figure8 ) ...

  • Dell 420 - page 8

    1. Disconnect the control panel cable from the PANEL connector on the system board (see Figure 22 for the location of the PANEL connector). 2. Remove the mounting screw that secures the control panel to the chassis. 3. Disconnect the chassis intrusion switch cable connector from the control panel. 4. Disconnect the thermal sensor cable connector fr ...

  • Dell 420 - page 9

    Figure 11. Drive Locations Diskette Drive Removal To remove the 3.5 - inch diskette drive assembly, perform the following steps: 1. Rotate the system power supply up and out of the system (see Figure 20 ). 2. Disconnect the DC power cable from the back of the diskette drive. 3. Disconnect the interface ribbon cable from the back of the diskette dri ...

  • Dell 420 - page 10

    6. Rotate the left side of the diskette drive up until the drive is clear of the retaining tabs. When you replace the 3.5 - inch diskette drive on the bracket, be sure that the two retaining tabs on the right side of the bracket engage the mounting holes in the side of the 3.5 - inch diskette drive. Then replace the screw that holds the diskette dr ...

  • Dell 420 - page 11

    Hard - Disk Drive Bracket Removal To remove the hard - disk drive bracket, perform the following steps. NOTICE: If you are removing a hard - disk drive that contains data you want to keep, be sure you have a backup of your files before you begin this procedure. 1. Remove the computer cover . 2. Disconnect the DC power cable and data cable from the ...

  • Dell 420 - page 12

    1. Remove the four screws that secure the hard - disk drive to the drive bracket. Retain these screws; they will be needed for the replacement drive. 2. Remove the hard - disk drive. Hard - Disk Drive Replacement To install a replacement hard - disk drive, perform the following steps. 1. If you are replacing a hard - disk drive that contains data y ...

  • Dell 420 - page 13

    8. Connect a DC power cable to the power input connector on the back of the drive (see Figure19 ). Check all connectors to be certain that they are properly cabled and firmly seated. 9. Connect one of the device connectors on the EIDE cable to the 40 - pin interface connector on the back of the hard - disk drive. NOTICE: You must match the color ...

  • Dell 420 - page 14

    15. Test the hard - disk drive by running the Dell Diagnostics (see the online System User's Guide for more information). 16. If the drive you just installed is the primary drive, install your operating system on the hard - disk drive. Refer to the documentation that came with your operating system. Power Supply To access some components on th ...

  • Dell 420 - page 15

    4. Rotate the power supply up and out of the way of the system board (see Figure 20 ). 5. Disconnect the power supply connectors from the POWER_1 and POWER_2 connectors on the system board. 6. Carefully fold the DC power supply cables you have disconnected and place them outside the chassis. 7. With the power supply in its rotated position up and a ...

  • Dell 420 - page 16

    System Board Jumpers Figure 23 shows the location of the jumpers on the system board. Table1 lists the system board jumpers and their settings. Figure 23. System Board Jumper s Jumpers are small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects the pins a ...

  • Dell 420 - page 17

    System Board Labels Table 2 lists the labels for connectors and sockets on your system board, and it gives a brief description of their functions. Table 2. System Board Connector and Socket Labels RIMMs Connector or Socket Label Description AGP AGP graphics card slot AUX_LED Hard - disk drive LED connector Battery Battery socket CD_IN CD - ROM audi ...

  • Dell 420 - page 18

    To remove a Rambus in - line memory module (RIMM), perform the following steps. 1. Remove the computer cover . 2. PressthesecuringclipsoutwardsimultaneouslyuntiltheRIMMdisengagesandpopsoutslightlyfromthesocket(seeFigure24). Figure 24. RIMM Removal To install replacement memory, perform the fo ...

  • Dell 420 - page 19

    The system detects that the new memory does not match the existing system configuration information and generates the following message: The amount of system memory has changed. Strike the F1 key to continue, F2 to run the setup utility 5. Press <F2> to enter System Setup, and check the value for System Memory . The system should have already ...

  • Dell 420 - page 20

    Figure 27. Microprocessor Replacement To insert the new microprocessor/heat sink assembly into the system board connector, perform the following steps (this procedure assumes the microprocessor removal procedure was just performed). 1. Press the processor firmly into its connector until it is fully seated. You must use up to 25 lb of force to fully ...

  • Dell 420 - page 21

    4. Rotate the power supply back into position, making sure that the securing tab snaps into place. 5. Replace the computer cover, and reconnect your computer and peripherals to their power sources and turn them on. 6. Enter System Setup and confirm that the top line in the System Data area correctly identifies the installed processor(s). 7. While i ...

  • Dell 420 - page 22

    To remove the system battery, perform the following steps: 1. If possible, enter System Setup and print the System Setup screens. If the settings are lost while you are replacing the battery, you can refer to your written or printed cop of the system configuration information to restore the correct settings. 2. To access the battery on the system b ...

  • Dell 420 - page 23

    1. Remove the computer cover . 2. Disconnect all cables from their connectors at the back of the computer. 3. Rotate the power supply . 4. Disconnect all cables from the system board. 5. Remove the RIMMs . 6. Remove the airflow shroud, the primary processor, and the secondary processor or terminator card . 7. Remove all expansion cards from the sys ...

  • Dell 420 - page 24

    Back to Contents Page Mini Tower Chassis — RemovingandReplacingParts:DellPrecision™WorkStation 420 Systems Service Manual Overview This section provides procedures for removing and replacing the components, assemblies, and subassemblies in the Dell Precision WorkStation 420 mini tower chassis system. Unless otherwise noted, ...

  • Dell 420 - page 25

    Restarting the System To restart the system and reset the chassis intrusion detector, perform the following steps: 1. Replace the computer cover and reconnect the computer and peripherals to their power sources and turn them on. ALERT! Cover was previously removed. 2. To reset the chassis intrusion detector, enter System Setup, select System Securi ...

  • Dell 420 - page 26

    4. Lift the bottom of the cover, allowing it to pivot up toward you. 5. Disengage the tabs that secure the cover to the top of the chassis, and lift the cover away. Figure 3. Computer Cover Replacement To replace the computer cover, perform the following steps: 1. Check all cable connections, especially those that might have come loose during your ...

  • Dell 420 - page 27

    Interior Service Label Figure 4 shows the location of the interior service label on the inside of the system cover. This label shows the location of components within the chassis and locations of system board components and connectors. It also contains an important notice that provides instructions you need to follow to help prevent damage to your ...

  • Dell 420 - page 28

    To remove the front panel, perform the following steps: 1. While pressing the tab release marked with the icon, tilt the panel away from the chassis. 2. Disengage the two retaining hooks at the bottom of the panel. 3. Carefully pull the panel away from the chassis. To replace the front panel, perform the following steps: 1. Fit the two retaining ho ...

  • Dell 420 - page 29

    Drives Figure 8. Drive Locations Diskette Drive Removal To remove the 3.5 - inch diskette drive assembly, perform the following steps: 1. Disconnect the DC power/interface cables from the back of the diskette drive. Note the routing of the DC power/interface cables through the chassis as you disconnect them. It is important to route the cables prop ...

  • Dell 420 - page 30

    Figure 10. 3.5 - Inch Diskette Drive Bracket 5.25 - Inch Diskette, LS - 120 SuperDisk, Tape, or CD - ROM Drive Removal To remove a diskette, LS - 120 SuperDisk, tape, or CD - ROM drive, perform the following steps: 1. Remove the computer cover . 2. Disconnect the DC power cable and interface cable from the back of the drive. 3. Squeeze the metal ta ...

  • Dell 420 - page 31

    5.25 - Inch Diskette, Tape, or CD - ROM Drive Replacement To install a replacement 5.25 - inch diskette, tape, or CD - ROM drive, perform the following steps. 1. Unpack the replacement drive and prepare it for installation. NOTICE: Ground yourself by either wearing a wrist grounding strap or by touching an unpainted metal surface on the computer ch ...

  • Dell 420 - page 32

    7. Connect a DC power cable to the power input connector on the back of the drive (see Figure 14 ). 8. Connect the appropriate interface cable to the interface connector on the back of the drive (see Figure14 ). If your system came with an EIDE CD - ROM or tape drive, use the spare connector on the existing interface cable. Otherwise, use the EI ...

  • Dell 420 - page 33

    Hard - Disk Drive Removal 1. Remove the computer cover . 2. Remove the front panel as instructed in " Front Panel ." 3. Disconnect the DC power cable and EIDE or small computer system interface (SCSI) cable from the drive. 4. Pull the drive door forward and down until the hard - disk drive bracket is ejected halfway out of the chassis (se ...

  • Dell 420 - page 34

    6. Reinstall the hard - disk drive bracket in the chassis (see Figure 17 ). Insert the bracket into the chassis by sliding it in until the tabs snap into place. Rotate the drive door up and toward the chassis until it snaps securely into place. Be sure to fold down the drive door handle (see Figure 17 ) so that the front panel can be replaced on th ...

  • Dell 420 - page 35

    9. If it is not already connected, connect the other end of the EIDE cable to the IDE1 connector on the system board. NOTICE: You must match the colored strip on the EIDE cable with pin 1 on the IDE1 connector to avoid possible damage to your system. 10. Replace the computer cover and the front panel. Then reconnect your computer and peripherals to ...

  • Dell 420 - page 36

    3. Slide the card brace forward until it disengages from the slot in the card guide, then rotate the brace up and lift it away from the chassis. To replace the card brace, perform the following steps: 1. Insert the tab on the end of the card brace into the slot above the card guide at the front of the chassis (see Figure 19 ). 2. Lower the card bra ...

  • Dell 420 - page 37

    Figure 21 shows the AGP card extension that occludes PCI slots 1 and 2. The following is a list of valid expansion - card combinations: l One AGP card and five PCI cards l One AGP card, four PCI cards, and one RAID card l One AGP Pro50 card and four PCI cards l One AGP Pro50 card, three PCI cards, and one RAID card One AGP Pro110 card and three PCI ...

  • Dell 420 - page 38

    Figure 22. Installing an Expansion Card 5. When the card is firmly seated in the connector, secure the card's mounting bracket to the chassis with the screw you removed in step 5 of the removal procedure. 6. Connect any cables that should be attached to the card. Expansion - Card Guide and Fan Figure 23. Expansion - Card Guide and Fan Removal ...

  • Dell 420 - page 39

    To remove an expansion - card guide cooling fan, perform the following steps. 1. Remove the computer cover according to the instructions in " Computer Cover ." 2. Rotate the power supply . 3. Remove the expansion - card guide and fan . 4. Squeeze the tabs on the end of the fan bracket and slide the fan off of the expansion - card guide ( ...

  • Dell 420 - page 40

    To remove the chassis intrusion switch and install a replacement, perform the following steps: 1. Disconnectthechassisintrusionswitchcablefromthecontrolpanel(see Figure 26 ). Note the routing of the chassis intrusion cable as you remove the cable from the chassis. The cable is routed through an enlarged hole in the ...

  • Dell 420 - page 41

    4. Lift the release latch and slide the power supply about 25 mm (1 inch) toward the front of the system. 5. Continue to apply pressure on the release latch while pulling the power supply towards the front of the computer and rotating the power supply out of the chassis. See the instruction label on the side of the power supply for additional infor ...

  • Dell 420 - page 42

    1 CD - ROM drive audio connector 2 Main power 1 connector (desktop chassis) 3 Diskette connector 4 Main power 2 connector (desktop chassis) 5 Battery 6 RIMM (memory) sockets 7 SCSI narrow connector 8 Secondary EIDE connector 9 Suspend - To - RAM LED 10 Jumper block (see " System Board Jumpers ") 11 System board screw 12 LVD SCSI connector ...

  • Dell 420 - page 43

    System Board Jumpers Figure 29 shows the location of the jumpers on the system board. Table1 lists the system board jumpers and their settings. Figure 29. System Board Jumpers Jumpers are small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects the pins an ...

  • Dell 420 - page 44

    RIMMs To remove a Rambus in - line memory module (RIMM), perform the following steps. 1. Remove the computer cover according to the instructions in " Computer Cover ." 2. Press the securing clips outward simultaneously until the RIMM disengages and pops out slightly from the socket (see Figure 30 ). Figure 30. RIMM Removal To install a RI ...

  • Dell 420 - page 45

    2. If necessary, remove any RIMMs that occupy sockets in which you plan to install the RIMMs. 3. Install the RIMMs. a. Locate the plastic securing clips at each end of the socket (see Figure 31 ). b. Press the clips outward until they snap open. c. Press the RIMM straight into the slot running down the center of the socket until the securing tabs s ...

  • Dell 420 - page 46

    1. Remove the computer cover . 2. Rotate the power supply . 3. Remove the existing microprocessor from its connector. Squeeze in on the two pairs of tabs on the airflow shroud and lift it away. Press outward on the guide bracket tabs to release them from the processor/heat sink assembly. Remove the two thumbscrews. Then pull the processor/heat sink ...

  • Dell 420 - page 47

    Press the processor firmly into its connector until it is fully seated. You must use up to 25 lb of force to fully seat the processor in its connector. 5. Install the two thumbscrews. 6. Replace the airflow shroud. 7. Rotate the power supply back into position, making sure that the securing tab snaps into place. 8. Replace the computer cover, and r ...

  • Dell 420 - page 48

    Battery Figure 35. Battery Removal  To remove the system battery, perform the following steps: 1. If possible, enter System Setup and print the System Setup screens. 1 Battery 2 Socket CAUTION: There is a danger of the new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by t ...

  • Dell 420 - page 49

    To remove the system board, perform the following steps. 1. Remove the computer cover . 2. Disconnect all cables from their connectors at the back of the computer. 3. Rotate the system power supply . 4. Disconnect all cables from the system board. 5. Remove the RIMMs . 6. Remove the airflow shroud, the primary processor, and the secondary processor ...

Produzent Dell Kategorie Personal Computer

Dokumente, die wir vom Produzenten des Geräts Dell 420 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Dell
- Bedienungsanleitungen 420
- Produktkarten Dell
- Informationsbroschüren
- oder Energieetiketten Dell 420
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Dell 420.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Dell 420, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Dell 420. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Dell 420 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Dell 420, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Dell 420 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Dell 420 verständlich ist.

Eine gänzliche Bedienungsanleitung von Dell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Dell 420 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Dell 420 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Dell 420, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Dell 420 - die uns die ersten Schritte während der Nutzung von Dell 420 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Dell 420 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Dell 420 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Dell 420?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Dell 420 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Dell 420 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)