Deutsch dropdown-ico

Bedienungsanleitung Zenoah HTZ2500

36 Seiten 0.48 mb
Download

Zur Seite of 36

Summary
  • Zenoah HTZ2500 - page 1

    The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING HTZ2500 CHTZ2500 OWNER / OPERA T OR MANUAL HEDGE-TRIMMERS HTZ2500 CHTZ2500  Thank you for purchasing a RedMax product. Before using our hedge-trimmers, please read this manual carefully to un ...

  • Zenoah HTZ2500 - page 2

    ...

  • Zenoah HTZ2500 - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • Zenoah HTZ2500 - page 4

    1. Parts location 1 2 2 3 4 5 5 6 6 7 8 8 9 9 10 11 [ HTZ2500 ] [ CHTZ2500 ] 3 ❲ 4 ❳ 1. Right handle 2. Fuel tank 3. Starter 4. Left handle 5. Throttle lever 6. Ignition switch 7. Throttle Cable 8. Muffler 9. Blade 10. Front handle 11. Rear handle ...

  • Zenoah HTZ2500 - page 5

    2. Specifications Engine Type ······················································································ Air-cooled 2-stroke gasoline Model ························································ ...

  • Zenoah HTZ2500 - page 6

    ❲ 6 ❳ (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). Never modify your machine. We won't wa ...

  • Zenoah HTZ2500 - page 7

    For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: AIR CLEAN ...

  • Zenoah HTZ2500 - page 8

    ❲ 8 ❳ 5. For safe operation 1 . Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased th ...

  • Zenoah HTZ2500 - page 9

    b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product. ■ WO ...

  • Zenoah HTZ2500 - page 10

    ❲ 10 ❳ ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more ...

  • Zenoah HTZ2500 - page 11

    Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit ...

  • Zenoah HTZ2500 - page 12

    ❲ 12 ❳ • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. ■ MAIN ...

  • Zenoah HTZ2500 - page 13

    5. For safe operation ■ HANDLING FUEL 1. The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ig ...

  • Zenoah HTZ2500 - page 14

    ❲ 14 ❳ • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m(10ft) away from the fueling point before starting the engine. • The RedMax engines are lubricated by oil specially ...

  • Zenoah HTZ2500 - page 15

    container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification. ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a dustless place. 2 . Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillag ...

  • Zenoah HTZ2500 - page 16

    ❲ 16 ❳ ■ STARTING ENGINE The cutting head will start rotating upon the engine starts. 1 . Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2 . Push the primer pump several times until overflown fuel flows out in the clear tube. (OP ...

  • Zenoah HTZ2500 - page 17

    7. Operation 1 . When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. ■ STOPPING ENGINE (OP3) 1. Release the thrott ...

  • Zenoah HTZ2500 - page 18

    • Weather conditions and altitude may effect carburation. • Do not allow anyone to stay close to the hedge-trimmer while working or while adjusting the carburetor. ■ HOW TO USE HANDLE (CHTZ2500 only) To reduce fatigue when trimming hadges, the handle can be swivelled through 90° to the left or right. (OP7, OP8). Do not press the throttle dur ...

  • Zenoah HTZ2500 - page 19

    7. Operation OP9 OP11 OP12 OP10 ❲ 19 ❳ HEDGE TRIMMING TECHNIQUES Trim sides of a hedge first, and then the top. Vertical cut: • With the single-sided blade hedge-trimmer, model HTZ2500 always cut from the bottom up (OP9). With the 2-sided blade model CHTZ2500 use an arcing cut from the bottom upwards, then downwards to use both sides of the b ...

  • Zenoah HTZ2500 - page 20

    ❲ 20 ❳ 8. Maintenance every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.17) if necessary clea ...

  • Zenoah HTZ2500 - page 21

    • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely be ...

  • Zenoah HTZ2500 - page 22

    ❲ 22 ❳ ■ MUFFLER • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ INTAKE AIR COOLING VENT • Never touch the cylinder, muffler, or s ...

  • Zenoah HTZ2500 - page 23

    8. Maintenance ■ BLADES Oil blades each gas tank filling (MA5). • Make sure that the blade bolts are well tightened. • The blade assembly is designed to automatically compensate for any play between the blades. ■ SHARPENING (MA6) Always keep the file or sharpener at an angle of 45° to the blade, and: • Always grind in the direction of th ...

  • Zenoah HTZ2500 - page 24

    10. T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ➞ clean/dry ➞ plug gap i ...

  • Zenoah HTZ2500 - page 25

    1 1. Parts list ❲ 25 ❳ NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model ...

  • Zenoah HTZ2500 - page 26

    1 1. Parts list ❲ 26 ❳ Fig.1 CUTTING UNIT HTZ2500 (S/N 100101 and up) ...

  • Zenoah HTZ2500 - page 27

    Key# Description Part Number Q'ty 1 SCREW 3960067 5 2 HANDLE 58040143 1 3 NUT 3980014 4 4 PLATE 58040057 2 5 SWITCH GUARD 2317013 1 6 CLUTCH DRUM 58040218 1 7 DRIVE GEAR 58040217 1 8 GUARD 58040206 1 9 THROTTLE LEVER 58040084 1 10 SPRING 58040136 1 11 SCREW 3960082B 11 12 SCREW 3960073 8 14 REAR HANDLE 58040201 1 15 LEVER 58040085 1 16 SWITCH ...

  • Zenoah HTZ2500 - page 28

    1 1. Parts list ❲ 28 ❳ Fig.2 CUTTING UNIT CHTZ2500 (S/N 100101 and up) ...

  • Zenoah HTZ2500 - page 29

    Key# Description Part Number Q'ty 1 SCREW 3960067 7 2 FRONT HANDLE 58040185A 1 3 NUT 3980014 4 4 PLATE 58040057 2 5 SWITCH GUARD 2317013 1 6 CLUTCH DRUM 58040218 1 7 DRIVE GEAR 58040217 1 8 SPRING 58040080 2 9 THROTTLE LEVER 58040084 1 10 SPRING 58040136 1 11 SCREW 3960057 2 12 SCREW 3960073 7 13 GREASE NIPPLE 58040180 1 14 HANDLE 58040181 1 1 ...

  • Zenoah HTZ2500 - page 30

    Fig.3 ENGINE UNIT (S/N 100101 and up) ❲ 30 ❳ 1 1. Parts list ...

  • Zenoah HTZ2500 - page 31

    ❲ 31 ❳ Key# Description Part Number Q'ty 1 CYLINDER 4810-12111 1 2 GASKET 4810-12210 1 3 BOLT 4820-12130 2 4 INSULATOR 4810-13162 1 5 GASKET, INSU T1512-13120 1 6 GASKET, CARB 4810-13130 1 7 BOLT 4820-13180 2 8 REEDVALVE-A(S) 4810-16100 1 9 • VALVECASE(S) 4810-16110 1 10 • REEDVALVE 4810-16120 1 11 • STOPPER 4810-16130 1 12 • SCREW ...

  • Zenoah HTZ2500 - page 32

    The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on ...

  • Zenoah HTZ2500 - page 33

     EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: THE CARBUR ...

  • Zenoah HTZ2500 - page 34

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • Zenoah HTZ2500 - page 35

    ...

  • Zenoah HTZ2500 - page 36

    KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093  © Printed in Japan ...

Produzent Zenoah Kategorie Trimmer

Dokumente, die wir vom Produzenten des Geräts Zenoah HTZ2500 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Zenoah
- Bedienungsanleitungen HTZ2500
- Produktkarten Zenoah
- Informationsbroschüren
- oder Energieetiketten Zenoah HTZ2500
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Zenoah HTZ2500.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Zenoah HTZ2500, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Zenoah HTZ2500. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Zenoah HTZ2500 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Zenoah HTZ2500, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Zenoah HTZ2500 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Zenoah HTZ2500 verständlich ist.

Eine gänzliche Bedienungsanleitung von Zenoah sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Zenoah HTZ2500 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Zenoah HTZ2500 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Zenoah HTZ2500, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Zenoah HTZ2500 - die uns die ersten Schritte während der Nutzung von Zenoah HTZ2500 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Zenoah HTZ2500 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Zenoah HTZ2500 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Zenoah HTZ2500?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Zenoah HTZ2500 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Zenoah HTZ2500 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)