-
Hunter Fan M0099-01 - page 1
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 10 PA G E 5 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy Operation, Maintenanc e & Cleaning T roubleshooting Downrod Prepar ation T able of C ontents PA G E 11 PA G E 4 Mounting Options PA G E 13 Blades S ...
-
Hunter Fan M0099-01 - page 2
www .HunterF an.com 1.888.830.1326 M0099-01 • 05/06/14 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you . Check box to see fan weight Assess location 30 inches from blade tip to nea ...
-
Hunter Fan M0099-01 - page 3
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . 3 M0099-01 • 05/06/14 • © Hunter F an Company ...
-
Hunter Fan M0099-01 - page 4
www .HunterF an.com 1.888.830.1326 4 M0099-01 • 05/06/14 • © Hunter F an Company If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T I O N 1 Guide T ...
-
Hunter Fan M0099-01 - page 5
www .HunterF an.com 1.888.830.1326 C eiling Bracket Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. F or angled ceilings, point opening toward peak. If you are unable to do this, call ...
-
Hunter Fan M0099-01 - page 6
www .HunterF an.com 1.888.830.1326 Prepar ation D I S C A R D K E E P ! Remove the shipping blocks fr om the motor . Sav e the screws . They will be needed for blade iron installation. Note: Some fans will hav e a shipping ring instead of shipping blocks. Please remov e the ring and save the screws. Time Sav er Tip: Get a helper to insert grommets, ...
-
Hunter Fan M0099-01 - page 7
www .HunterF an.com 1.888.830.1326 7 M0099-01 • 05/06/14 • © Hunter F an Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to nex ...
-
Hunter Fan M0099-01 - page 8
www .HunterF an.com 1.888.830.1326 8 M0099-01 • 05/06/14 • © Hunter F an Company KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top o ...
-
Hunter Fan M0099-01 - page 9
www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan. 9 M0099-01 • 05/06/14 • © Hunter F an Company ...
-
Hunter Fan M0099-01 - page 10
www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x. Refer to CA UTION c.1 on pg. 2 10 M0099-01 • 05/06/14 • © Hu ...
-
Hunter Fan M0099-01 - page 11
www .HunterF an.com 1.888.830.1326 Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag. No te: Fan style may vary . 11 M0099-01 • 05/06/14 • © Hunter ...
-
Hunter Fan M0099-01 - page 12
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. Insert grommets found in the hardware bag into the holes in the blades, then secure each blade ...
-
Hunter Fan M0099-01 - page 13
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw , f ...
-
Hunter Fan M0099-01 - page 14
www .HunterF an.com 1.888.830.1326 14 M0099-01 • 05/06/14 • © Hunter F an Company Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secur e all three assembly screws could result in the light xture falling. Align the notches in the sides of the lower switch housing with the u ...
-
Hunter Fan M0099-01 - page 15
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) Connect the appropriate pull chain pendant to each of the short chains coming from the nial and nial cap . Press the globe and globe keeper ush against the metal plate. T hread the light pull chain through the hole in the center of the nial cap and thread the fan pull chain throu ...
-
Hunter Fan M0099-01 - page 16
www .HunterF an.com 1.888.830.1326 Remote C ontrol Note: The remote must be pair ed before the fan will operate . Within 3 minutes of rest oring power to the fan, press both the F an OFF button and the F an ON button for at least 4 seconds . Y our fan will turn on to indicate successful syncing. If it does not, turn off po wer to your fan, wait 1 m ...
-
Hunter Fan M0099-01 - page 17
www .HunterF an.com 1.888.830.1326 17 M0099-01 • 05/06/14 • © Hunter F an Company F an Operation: Press and quickly release the ON or OFF button on the remote control t o turn the fan OFF or ON. T o change the fan speed, slowly pull the fan pull-chain switch to select the desired speed . Light Opera tion: Press and quickly release the ON or OF ...
-
Hunter Fan M0099-01 - page 18
www .HunterF an.com 1.888.830.1326 Opera tion, Maintenance , & Cleaning (con tinued) Changing the bulbs - unscrew the nial and remo ve it from the threaded rod . Remove the nial cap and unscrew the globe keeper while suppor ting the globe with your other hand . Carefully remove the globe . Unscrew bulbs and replace with bulbs of same type ...
-
Hunter Fan M0099-01 - page 19
www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . Noisy Operation • Tighten the blade and blade iron screws until they are snug . • Check to see ...
Haben Sie eine Frage bezüglich Hunter Fan M0099-01?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hunter Fan M0099-01 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hunter Fan M0099-01 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.