-
Panasonic PT-VX400E - page 1
Operating Instructions Projector Operations LCD Projector Commercial Use Thank you for purchasing this Panasonic Product. Before operating this product, please read the instructions carefully and save this manual J for future use. For information on using the product via a network, refer to “Operating Instructions – Network Operations”. Model ...
-
Panasonic PT-VX400E - page 2
Read this rst! 2 - ENGLISH Important Information Read this rst! W ARNING: THIS APP ARA TUS MUST BE EAR THED. W ARNING: T o prevent damage which may result in re or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV , January 18, 1991: The sound pressure level at the operator position ...
-
Panasonic PT-VX400E - page 3
Read this rst! ENGLISH - 3 Important Information W ARNING: PO WER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur . If the following problems occur , cut off the power supply immediately . Continued use of the projector in these conditions will result in re or ...
-
Panasonic PT-VX400E - page 4
Read this rst! 4 - ENGLISH Important Information W ARNING: Installation work (such as ceiling mount bracket) should only be carried out by a qualied technician. If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks. Do not use anything other than an authorized ceiling mount bracket. ...
-
Panasonic PT-VX400E - page 5
Read this rst! ENGLISH - 5 Important Information W ARNING: ACCESSORI ES Do not use or handle the batteries improperly , and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re. Do not use unspecied batteries. z Do not disassemble dry cell batteries. z Do not heat the batter ...
-
Panasonic PT-VX400E - page 6
Read this rst! 6 - ENGLISH Important Information T o remove the battery Remote Control Battery 1 . P ress th e g u ide a nd l ift th e cover . 2. Remo ve the batteri es. CAUTION: ON USE /INST A LLA TION Do not put your weight on this projector . Y ou could fall or the projector could break, and injury will result. Be especially careful not t ...
-
Panasonic PT-VX400E - page 7
ENGLISH - 7 This function enables Input search, Auto Keystone correction and Auto PC adjustment by pressing the <AUT O SETUP> button. With the Direct Power Of f function, you can disconnect the power cord from the wall outlet or turn of f the breaker even during projection. The inclusion of an HDMI terminal provides support for high quality v ...
-
Panasonic PT-VX400E - page 8
8 - ENGLISH Important Information Preparation Getting Started Basic Operation Settings Maintenance Appendix Contents Be sure to read “Read this rst!”. ( pages 2 to 6) Important Information Read this rst! ........................................... 2 Precautions for Use................................. 10 Cautions when transporting ....... ...
-
Panasonic PT-VX400E - page 9
ENGLISH - 9 Important Information Preparation Getting Started Basic Operation Settings Maintenance Appendix Brightness .................................................................... 43 Color ............................................................................. 43 T int .................................................................. ...
-
Panasonic PT-VX400E - page 10
10 - ENGLISH Important Information Precautions for Use Cautions when transporting When transporting the projector , hold it securely by its bottom and avoid excessive vibration and impacts. z Doing so may damage the internal parts and result in malfunctions. Do not transport the projector with the adjustable feet extended. Doing so may damage the a ...
-
Panasonic PT-VX400E - page 11
Precautions for Use ENGLISH - 11 Important Information Cautio ns when se tting the pro jector s J z Do not stack the projectors. Do not block the ventilation ports (intake and exhaust) of the z projector . Avoid heating and cooling air from the air conditioning system z directly blow to the ventilation ports (intake and exhaust) of the projector . ...
-
Panasonic PT-VX400E - page 12
Precautions for Use 12 - ENGLISH Important Information Cautions on use I n ord er to get th e pi ctu re qu al ity J Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light z from indoor lamps from shining onto the screen. Depending on where the projector is used, heated air from an exhaust port ...
-
Panasonic PT-VX400E - page 13
Precautions for Use ENGLISH - 13 Important Information Accessories Make sure the following accessories are provided with your projector . Numbers in the brackets ( ) show the number of accessories. Remote control unit (x1) (6451048745) (6451048738) Power cord (x1) (6103580203) CD-ROM (x1) (6103564272) Batteries (AAA/R03 t ype) (x2) PT-VW330E PT-VX4 ...
-
Panasonic PT-VX400E - page 14
Precautions for Use 14 - ENGLISH Important Information Contents of the su pplied J CD-R OM The contents of the supplied CD-ROM are as follow . [ : Instructions/List (PDF), : Software] Operating Instructions – Projector Operations. Operating Instructions – Network Operations. Multi Projector Monitoring & Control Software ...
-
Panasonic PT-VX400E - page 15
ENGLISH - 15 Preparation About Y our Projector Remote control * <P IN P> button is only for PT -VW330E. (1) <AUTO SET> Button Execute the setting of Auto setup in the setting menu. ( Æ page 50) (2) Input Selection Buttons: <COMPUTER 1>, <COMPUTER 2>, <HDMI>, <VIDEO>, <S-VIDEO>, <COMPONENT>. These but ...
-
Panasonic PT-VX400E - page 16
About Y our Projector 16 - ENGLISH Preparation (1) Remote control signal receiver (2) Focus Ring Adjusts the focus. (3) Projection Lens (4) Zoom Lever Adjusts the zoom. (5) Air intake port (6) Control Panel and Indicators ( Æ page 17) (7) Lamp cover ( Æ page 63 ) The lamp unit is located inside. (8) Air outlet port Hot air is exhausted from the e ...
-
Panasonic PT-VX400E - page 17
About Y our Projector ENGLISH - 17 Preparation Rear terminals Control panel (1) LAN Connects to a LAN cable for network connection. (2) HDMI Connects to HDMI input signals. (3) COMPUTER IN 1/ COMPONENT IN Connects to COMPUTER IN 1/ COMPONENT IN input signals. (4) COMPUTER IN 2/ MONITOR OUT Connects to COMPUTER IN 2/ MONITOR OUT input signals or out ...
-
Panasonic PT-VX400E - page 18
Using Remote control 18 - ENGLISH Preparation Using Remote control Installing and Removing batteries Open the cover 1 ) Install batteries and close the cover 2 ) (Insert the – side rst.) Remove the batteries in the reverse order of z installation. Setting Remote control ID numbers When you use the system with multiple projectors, you can opera ...
-
Panasonic PT-VX400E - page 19
ENGLISH - 19 Getting Started Setting up Projection method Y ou can use the projector with any of the following 4 projection methods. T o set the desired method in the projector . J Mounting on the ceiling and projecting forward J Setting on a desk/oor and projecting from rear (Using translucent screen) J Mounting on the ceiling and projecting fr ...
-
Panasonic PT-VX400E - page 20
Setting up 20 - ENGLISH Getting Started Screen size and throw distance Place the projector referring to the diagram on the right and the gures of throwing distance. Y ou can adjust the display size L (L W/L T) Screen L (L W/L T) SW Screen SH SW SD Projected image SH L (L W/L T) * 1 Projection distance (m) SH Height of the projection area (m) SW ...
-
Panasonic PT-VX400E - page 21
Setting up ENGLISH - 21 Getting Started J Projection distance for PT -VX400E (All measurements below are approximate and may differ slightly from the actual measurements.) Projection size For 4:3 aspect ratio For 16:9 aspect ratio Screen diagonal (SD) Minimum distance (L W) Maximum distance (L T) Minimum distance (L W) Maximum distance (L T) 0.76 m ...
-
Panasonic PT-VX400E - page 22
Setting up 22 - ENGLISH Getting Started Adjusting front adjustable feet Lift the front of the projector and press the feet lock latches on both side of the projector . Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to a proper height and tilt. Y ou can turn the front adjustable feet to extend them. Y ou can ...
-
Panasonic PT-VX400E - page 23
ENGLISH - 23 Getting Started Connections Before connecting to the projector Read carefully the instruction manual for the device to be connected. z T urn off the power switch of the devices before connecting cables. z If any connection cable is not supplied with the device, or if no optional cable is available for connection of the z device, prepar ...
-
Panasonic PT-VX400E - page 24
24 - ENGLISH Basic Operation Powering ON/OFF Connecting the power cord Be sure to insert the attached power cord securely to its base to prevent it from coming off. Power cord holder J A power cord holder is designed to prevent the AC power cord from coming off the projector . Please insert the power cord into the power cord holder correctly as Pic ...
-
Panasonic PT-VX400E - page 25
Powering ON/OFF ENGLISH - 25 Basic Operation Power indicator The power indicator informs you the status of the power . Conrm the status of the <Power indicator> before operating the projector . Power indicator Indicator status Status No illumination or ashing The power cord is unplugged. RED Lit Press the ON/ST AND-BY ( ) button to star ...
-
Panasonic PT-VX400E - page 26
Powering ON/OFF 26 - ENGLISH Basic Operation Complete peripheral connections (with a 1 ) computer , VCR, etc.) before turning on the projector . Connect the projector ’s AC power cord into an 2 ) AC outlet. The POWER indicator lights red. Open the lens cap. Press the <ON/ST AND-BY> button to on the 3 ) control panel or on the remote control ...
-
Panasonic PT-VX400E - page 27
Powering ON/OFF ENGLISH - 27 Basic Operation Enter a PIN code PIN Code Input Dialog Box Press ▲▼ to enter a number . Press ► to x the number and move the red frame pointer to the next box. The number changes to . If you xed an incorrect number , use the Point ◄ button to move the pointer to the number you want to correct, and then ...
-
Panasonic PT-VX400E - page 28
Powering ON/OFF 28 - ENGLISH Basic Operation Press the <ON/ST AND-BY> button on the top 1 ) control or on the remote control, and Power off? appears on the screen. Press the <ON/ST AND-BY> button again to turn 2 ) off the projector . The POWER indicator starts to blink red, and the cooling fans keep running. At this time, you can unplug ...
-
Panasonic PT-VX400E - page 29
ENGLISH - 29 Basic Operation Projecting Check the connections of the peripheral devices and connection of the power cord ( Æ page 24) and switch on the power ( Æ page 26) to start the projector . Select the image and adjust the state of the image. Selecting the image Select an input signal. The image selected with the <COMPUTER 1>, <COMP ...
-
Panasonic PT-VX400E - page 30
30 - ENGLISH Basic Operation Basic operations by using the remote control Using the AUT O SET function This function allows you to automatically adjust Input search, Auto Keystone correction and Auto PC adjustment during signal input from a computer . button Press the <AUTO SET> button on the remote control. Note For details, see “Setting? ...
-
Panasonic PT-VX400E - page 31
Basic operations by using the remote control ENGLISH - 31 Basic Operation Using the KEYST ONE button This function allows you to correct keystone distortion. button If a projected picture still has keystone distortion after pressing the <AUTO SET> button, correct the image manually as follows: Press the <KEYSTONE> button on the remote c ...
-
Panasonic PT-VX400E - page 32
Basic operations by using the remote control 32 - ENGLISH Basic Operation Using the A V MUTE function button Press the < A V MUTE> button on the remote control to black out the image. T o restore to normal, press the < A V MUTE> button again or press any button. black out→ normal...... Note When use the <MUTE> button to release ...
-
Panasonic PT-VX400E - page 33
Basic operations by using the remote control ENGLISH - 33 Basic Operation Using the P IN P button (PT -VW330E Only) This function allows you to operate the Picture In Picture function. button Press <P IN P> button on the remote control. Note For details, see “P IN P” of "Setting" under Main menu. z ( Æ page 52) Using the MUTE b ...
-
Panasonic PT-VX400E - page 34
34 - ENGLISH Settings Menu Navigation Navigating through the menu Operating procedure J Press the <MENU> button. 1 ) The Main Menu screen appears. Press ▲▼ to select the Main Menu 2 ) item. Select the desired item from the 9 items: [Input], [PC adjust], [Image select], [Image adjust], [Screen], [Sound], [Setting], [Information] and [Netwo ...
-
Panasonic PT-VX400E - page 35
Menu Navigation ENGLISH - 35 Settings Main menu The main menu consists of the following 9 menu items. When a main menu item is selected, the screen changes to a submenu selection screen. Input PC adjust Image select Image adjust Screen Sound Setting Information Network Sub menu The sub-menu screen of the selected main menu appears, and you can set ...
-
Panasonic PT-VX400E - page 36
Menu Navigation 36 - ENGLISH Settings Image adjust [ ] Sub-menu item Factory default Page Contrast 32 43 Brightness 32 43 Color* 1 32 43 T int* 1 32 43 Color temp. Mid 43 Red 32 44 Green 32 44 Blue 32 44 Sharpness 8 44 Gamma 8 44 Noise reduction* 1 L1 44 Progressive* 1 L1 45 Reset - 45 Store - 45 When input video signal to the projector , these *1 ...
-
Panasonic PT-VX400E - page 37
ENGLISH - 37 Settings Input menu Select [Input] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Computer 1: RGB/Component /RGB (Scart) Press ▲▼ to select [Computer 1]. 1 ) Press ► to access the submenu. 2 ) Press ▲▼ to select RGB, Component 3 ) or ...
-
Panasonic PT-VX400E - page 38
Input menu 38 - ENGLISH Settings P AL/SECAM/NTSC/NTSC4.43/P AL-M/P AL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among P AL, SECAM, NTSC, NTSC 4.43, P AL-M and P AL-N. Component Auto The projector automatically detects an incoming video signal, and adjusts itself to optimize its performanc ...
-
Panasonic PT-VX400E - page 39
AUT O PC adjust ENGLISH - 39 Settings AUT O PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel AUT O PC adj. Auto PC adjustment function is provided to automatically adjust Fine sync, T otal dots, Horizontal and V ertical positions ...
-
Panasonic PT-VX400E - page 40
Manual PC adjust 40 - ENGLISH Settings Manual PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector . Manual PC adjustment enabl ...
-
Panasonic PT-VX400E - page 41
Manual PC adjust ENGLISH - 41 Settings Current mode Press ▲▼ to select [Current mode]. 1 ) Press ► or the <SELECT> button 2 ) to enter the next submenu to show H-sync freq. and V -sync freq. of the connected computer . Clamp Press ▲▼ to select [Clamp]. 1 ) Press the <SELECT> button to display 2 ) the adjustment dialog box. Pre ...
-
Panasonic PT-VX400E - page 42
42 - ENGLISH Settings Image select Select [Image select] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Dynamic For viewing pictures in a bright room. Press ▲▼ to select [Dynamic] and then press the <SELECT> button. Standard Normal picture mode pr ...
-
Panasonic PT-VX400E - page 43
Image adjust ENGLISH - 43 Settings Select [Image adjust] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Contrast Press ▲▼ to select [Contrast]. 1 ) Press the <SELECT> button to display 2 ) the adjustment dialog box. Press ◄► to adjust the sett ...
-
Panasonic PT-VX400E - page 44
Image adjust 44 - ENGLISH Settings Red Press ▲▼ to select [Red]. 1 ) Press the <SELECT> button to display 2 ) the adjustment dialog box. Press ◄► to adjust the setting value. 3 ) Operation Adjustment Adjustment range Press ►. deepen red tone Maximum value 63 Press ◄. lighten red tone Minimum value 0 Green Press ▲▼ to select [G ...
-
Panasonic PT-VX400E - page 45
Image adjust ENGLISH - 45 Settings Progressive Press ▲▼ to select [Progressive]. 1 ) Press the <SELECT> button to display 2 ) the dialog box. Press ◄► to select the desired item. 3 ) An interlaced video signal can be displayed in z progressive mode. Select one of the following options. Progressive cannot be selected when 480p, z 576p, ...
-
Panasonic PT-VX400E - page 46
Screen 46 - ENGLISH Settings Screen Select [Screen] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Normal Provide the image to t the screen size while maintaining the aspect ratio of the input signal. Press ▲▼ to select [Normal] and then press the &l ...
-
Panasonic PT-VX400E - page 47
ENGLISH - 47 Settings Custom adj. Adjust the screen scale and position manually with this function. Press ▲▼ to select [Custom adj.]. 1 ) Press ► or the <SELECT> button to 2 ) enter the next submenu. Press ▲▼ to choose the item you 3 ) want to adjust. Y ou can choose one from the items as below: z Scale H/V Adjust the Horizontal/V e ...
-
Panasonic PT-VX400E - page 48
48 - ENGLISH Settings Ceiling This function is used to project the image from a ceiling-mounted projector . Press ▲▼ to select [Ceiling] and then 1 ) press the <SELECT> button. Press ▲▼ to change the image. 2 ) When this function is set to On, the picture will z be top/bottom and left/right reversed. Rear This function is used to proj ...
-
Panasonic PT-VX400E - page 49
Sound ENGLISH - 49 Settings Sound Select [Sound] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel V olume Press ▲▼ to select [V olume] and then 1 ) Press the <SELECT> button. Press ◄► to adjust the volume. 2 ) Operation Adjustment Adjustment ran ...
-
Panasonic PT-VX400E - page 50
Setting 50 - ENGLISH Settings Setting Select [Setting] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Language Press ▲▼ to select [Language]. 1 ) Press ► or the <SELECT> button. 2 ) Press ▲▼ to select the desired 3 ) language. The language u ...
-
Panasonic PT-VX400E - page 51
Setting ENGLISH - 51 Settings Auto keystone J Auto Always works and corrects keystone distortion according to the projector's tilt. Manual Works only when pressing the <AUT O SET> button on the remote control or the <AUTO SETUP> button on the control panel. Off Disables Auto Keystone. Note Input search, Auto PC adj. and Auto Keysto ...
-
Panasonic PT-VX400E - page 52
Setting 52 - ENGLISH Settings Logo PIN code change J Logo PIN code can be changed to your desired four- digit number . Press ▲▼ to select [Logo PIN code 1 ) change]. Press the <SELECT> button. 2 ) Current logo PIN code dialog box appears. z Press ▲▼ to enter the current code. 3 ) The New Logo PIN code input dialog box z appears. Set a ...
-
Panasonic PT-VX400E - page 53
Setting ENGLISH - 53 Settings X Subpicture size J Press ▲▼ to select [Subpicture size] 1 ) and then press the <SELECT> button. Press ▲▼ to select one among the 2 ) items as below . Y ou can change the subpicture size among z Small, Middle and Large. Subpicture position J Press ▲▼ to select [Subpicture 1 ) posi tion] and then p res ...
-
Panasonic PT-VX400E - page 54
Setting 54 - ENGLISH Settings Press ► or <SELECT> button to 2 ) access the submenu. Mode J Press ▲▼ button to select one mode 1 ) among the items as below . Count up The P-timer display 000:00 appears on the screen and the count up starts (000:00-180:00) Count down The time set in the T imer setting appears on the screen and the countdo ...
-
Panasonic PT-VX400E - page 55
ENGLISH - 55 Settings Lamp power This function allows you to change brightness of the screen. Press ▲▼ to select [Lamp power] and 1 ) then press the <SELECT> button . Press ▲▼ to select one among the 2 ) modes as below . Y ou can also press the <LAMP> button to z display [Lamp power]. Auto Brightness according to the input signa ...
-
Panasonic PT-VX400E - page 56
Setting 56 - ENGLISH Settings PIN code change J The PIN code can be changed to your desired four- digit number . Press ▲▼ to select [PIN code change] 1 ) and then Press <SELECT> button. Current Pin code dialog box appears. z Press ▲▼ to enter the current code. 2 ) Press ► button to x the number and move the red frame pointer to t ...
-
Panasonic PT-VX400E - page 57
Setting ENGLISH - 57 Settings Press ▲▼ to set the Timer . 2 ) Select from (Off/1000H/2000H/3000H/40 z 00H/5000H/6000H) depending on the use environment. Filter counter reset J After replacing the lter , be sure to reset the timer . Press ▲▼ to select [Filter counter 1 ) reset]. Press the <SELECT> button. 2 ) [Filter counter Reset?] ...
-
Panasonic PT-VX400E - page 58
Information 58 - ENGLISH Settings Select [Information] from the Main Menu (see “Navigating through the menu” on page 34), then select the item from the sub-menu. Remote Control Control Panel Input Source Information Display The Information Menu is used for checking the status of the image signal being projected and the operation of the projecto ...
-
Panasonic PT-VX400E - page 59
LAMP REPLACE and W ARNING Indicators ENGLISH - 59 Maintenance LAMP REPLACE and W ARNING Indicators Managing the indicated problems If a problem should occur inside the projector , the POWER, LAMP REPLACE and/or W ARNING indicators will inform you. Manage the indicated problems as follow . CAUTION Before you take a remedial measure, follow the proce ...
-
Panasonic PT-VX400E - page 60
60 - ENGLISH Maintenance Replacement Before replacing the unit When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect z the power plug from the wall outlet. ( Æ pages 24, 28) Be sure to observe the procedure “T uring off the projector” ( z Æ page 28) when performing power supply operation. Mai ...
-
Panasonic PT-VX400E - page 61
Replacement ENGLISH - 61 Maintenance cover (side); pull out the handle and take out the side lter . Replace the air lter units. 2 ) Put new lters back into the position. Make sure z that the lters are fully inserted to the projector . R ese tt ing t he Filter Counter J Be sure to reset the Filter counter after replacing the lter .( ? ...
-
Panasonic PT-VX400E - page 62
Replacement 62 - ENGLISH Maintenance CAUTION: ■ Do not replace the lamp unit when it is hot. (W ait at least 45 minutes after use.) The inside of the cover can become very hot, take care to avoid burn injuries. Notes on the replacement of the lamp unit J The luminous source of the lamp is made of glass and may burst z if you hit it against a hard ...
-
Panasonic PT-VX400E - page 63
Replacement ENGLISH - 63 Maintenance J Replacing the Lamp unit CAUTION: When the projector is mounted on a ceiling, do not work with your face close to the projector . z Attach the lamp unit and the lamp cover securely . z When you experience difculty in installing the lamp, remove it and try again. If you use force to install the z lamp, the co ...
-
Panasonic PT-VX400E - page 64
Replacement 64 - ENGLISH Maintenance Attaching the Lens Cap When moving this projector or while not using it over an extended period of time, attach the lens cap. Attach the lens cap according to the following procedures. Thread the string through the hole on the 1 ) lens cap and then tie a knot in the string to secure it in place. T o pass the oth ...
-
Panasonic PT-VX400E - page 65
ENGLISH - 65 Maintenance T roubleshooting Please check following points. For details, see the corresponding pages. Problem Cause Reference page Power does not turn on. The power cord may not be connected. z — No electric supply is at the wall outlet. z — The circuit breakers have tripped. z — Is the <LAMP REPLACE in dicator >, <PO WE ...
-
Panasonic PT-VX400E - page 66
T roubleshooting 66 - ENGLISH Maintenance Problem Cause Reference page Picture from a HDMI device does not appear or picture is not stable. Is the HDMI cable securely connected? z 23 T urn off the power of the projector and the connected devices. Then turn z the power of the projector and the connected devices back on. — Isn't unsupported si ...
-
Panasonic PT-VX400E - page 67
ENGLISH - 67 Appendix T echnical Information Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specication, so that the projector can be controlled by a personal computer which is connected to this connector . J Connection J Pin assignments and signal names D-Sub 9-pin (male) ...
-
Panasonic PT-VX400E - page 68
T echnical Information 68 - ENGLISH Appendix J Basic format T ransmission from the computer begins with STX, then the command, parameter , and ETX are sent in this order . Add parameters according to the details of control. STX C1 C2 C3 : P1 P2 Pn ETX When sending commands without parameters, a colon (:) is not necessary . : J Basic format (wit ...
-
Panasonic PT-VX400E - page 69
T echnical Information ENGLISH - 69 Appendix J Cable specications [When connected to a computer] Projector 1 NC NC 1 Computer (DTE specications) 2 2 3 3 4 NC NC 4 5 5 6 6 7 7 8 8 9 9 J Control commands When controlling the projector from a computer , the following commands are available: [Projector control command] Command Control contents Re ...
-
Panasonic PT-VX400E - page 70
T echnical Information 70 - ENGLISH Appendix Other terminals Pin assignments and signal names of <S-VIDEO IN> terminal J Outside view Pin No. Signal names GND (luminance signal) GND (color signal) Luminance signal Color signal Pin assignments and signal names of <COMPUTER IN 1/COMPONENT J IN> terminal Outside view Pin No. Signal names : ...
-
Panasonic PT-VX400E - page 71
T echnical Information ENGLISH - 71 Appendix T wo window display combination list (PT -VW330E Only) o : Picture in Picture combinations are enabled. x : Picture in Picture combinations are disabled Note When the input signal(s) is/are incompatible, mark will be displayed on the Main/Sub picture z . Depending on the frequency or signal type of PC/A ...
-
Panasonic PT-VX400E - page 72
T echnical Information 72 - ENGLISH Appendix List of compatible signals The following table species the types of signals compatible with the projectors. Format : V = VIDEO, S = S-VIDEO, C = COMPUTER, Y = YP B P R , H = HDMI Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP Format H (kHz) V (H ...
-
Panasonic PT-VX400E - page 73
T echnical Information ENGLISH - 73 Appendix Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP Format H (kHz) V (Hz) P T- VW330E P T- VX400E COMPUTER HDMI XGA 1024 x 768 48.36 60.00 65.00 A AA H/C 68.677 84.977 94.504 A AA ○ ○ 60.023 75.03 78.75 A AA ○ ○ 56.476 70.07 75.00 A AA ○ ○ 6 ...
-
Panasonic PT-VX400E - page 74
T echnical Information 74 - ENGLISH Appendix Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP Format H (kHz) V (Hz) P T- VW330E P T- VX400E COMPUTER HDMI D-SXGA+3 1400 x 1050 65.120 59.900 122.430 UXGA 1600 x 1200 75.00 60.00 162.00 A A ○ C 81.25 65.00 175.50 87.5 70.00 189.00 AA A ○ 93.75 ...
-
Panasonic PT-VX400E - page 75
T echnical Information ENGLISH - 75 Appendix Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP Format H (kHz) V (Hz) P T- VW330E P T- VX400E COMPUTER HDMI D-SXGA 1280 x 1024 63.98 60.02 108 60.276 58.069 93.067 31.65 29.8 53.48 D-1035i 1920 x 1035i 33.75 60.00 74.25 D-1080/50i 1920 x 1080i 28.12 ...
-
Panasonic PT-VX400E - page 76
76 - ENGLISH Appendix Specications Model No. PT-VW330E PT -VX400E Power supply AC100 V - 240 V 50 Hz/60 Hz Power consumption 100 V - 240 V 3.8 A-1.8 A 322 W When [Standby mode] of [Setting] is set to [ECO]: 0.48W When [Standby mode] of [Setting] is set to [Network]: 12.5W When [Standby mode] of [Setting] is set to [Network]: 10.0W When [Standby ...
-
Panasonic PT-VX400E - page 77
Specications ENGLISH - 77 Appendix Model No. PT-VW330E PT -VX400E T erminals COMPUTER IN 1/ COMPONENT IN 1 (D-sub 15 pin female) [RGB signal] 0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 [p-p] 75 Ω HD/SYNC TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible [YP B P R ...
-
Panasonic PT-VX400E - page 78
Ceiling mount bracket safeguards 78 - ENGLISH Appendix Dimensions <Unit : mm> 254.4 （ 10.0" ） 97.0 （ 3.82" ） 87.5 （ 3.44" ） 9.5 （ 0.38" ） 350.0 （ 13.78" ） 81.03 (3.19") 52.3 （ 2.06" ） 3.8 （ 0.15" ） Actual dimension may differ by product. : Ceiling mount bracket safeguards ...
-
Panasonic PT-VX400E - page 79
ENGLISH - 79 Appendix Index A About Y our Projector ....................... 15 Accessories .................................... 13 Adjusting front adjustable feet ........ 22 Attaching the Lens Cap .................. 64 AUTO PC adjust ............................. 39 Auto setup ...................................... 50 A V MUTE .................... ...
-
Panasonic PT-VX400E - page 80
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries ...
¿Tienes una pregunta acerca de Panasonic PT-VX400E?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Panasonic PT-VX400E, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Panasonic PT-VX400E probablemente compartirá una forma de solucionarlo.