-
Taylor C717 - page 1
OPERATOR'S MANUAL Model C709 & C717 Heat Treatment Soft Serve Freezers Original Operating Instructions 062080-M 2/4/ 05 (Ori ginal P ubli cati on) (Up da ted 9 /2 /14 ) ...
-
Taylor C717 - page 2
Com plete this pa ge for quick r efer ence w hen ser vice is r equir ed: Taylor Distributor: Address: Phone: Fax: E-mai l: Serv ice: Par ts: Date of Installation: Infor mati on found on the data la bel: Model Number: Seri al Number: Electrical S pecs: Voltage Cycle Phase Maximum Fuse Si ze: A Minimum Wi re Ampaci ty: A E 2005 Carrier Commer cial Re ...
-
Taylor C717 - page 3
Table of Cont ents Models C 70 9 & C7 17 T able of Contents Section 1 To the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 ....................................................... Air Cool ed Units 1 ........................................ ...
-
Taylor C717 - page 4
Mode ls C70 9 & C7 17 Table of Cont ents Table of Contents - P age 2 Draining P roduct From The F reezing Cyli nder 43 ............................ Rinsing 43 .............................................................. Hopper Cleani ng 44 ...................................................... Disassemb ly 44 ................................. ...
-
Taylor C717 - page 5
1 Mo del s C709 & C717 To the Insta ller 131 121 Section 1 To the Installer The f ollowing infor mation has been included in t he manual as saf ety and regulat ory guidelines. F or complet e inst allation inst ruct ions, please see t he Inst allat ion Checklist . Installer Safety In all areas of the world, equipment should be installed i n acco ...
-
Taylor C717 - page 6
2 Mo del s C709 & C717 To the Insta ller 130225 Water C onnections (W ater Coo led Un its O nl y) An adequate c old water supply m ust be pr ovided with a hand shut -of f v alve. O n the under side of the base pan or on t he right side, two 3/ 8” I .P. S. water connect ions f or inlet and out let ar e provided f or easy hook-up. 1/ 2” insid ...
-
Taylor C717 - page 7
3 Mo del s C709 & C717 To the Insta ller 130819 Beater Rotation Beater rot ation m ust be c lockwise as viewed looking int o the f reezing cy linder. Note: T he f ollowing procedures should be perf ormed by a t rained ser vice t echnician. To c orrect rot ation on a t hree-phas e unit, inter change any t wo incoming power s upply lines at fr ee ...
-
Taylor C717 - page 8
4 Mo del s C709 & C717 To the Opera tor 131 121 Section 2 To the Operator Your f reezer has been car efully engineer ed and manuf actur ed to give y ou dependable operation. When pr operly operat ed and cared f or, it will produce a c onsist ent, quality product . Lik e all mechanic al product s, c leaning and maintenanc e will be required. A m ...
-
Taylor C717 - page 9
5 Mo del s C709 & C717 Safety 130128 Se cti on 3 Sa fety We, at T aylor Company, ar e concerned about the safet y of the oper ator when he or she c omes in contac t wit h the f reezer and its part s. T aylor has gone to ex trem e eff orts to des ign and manuf actur e built- in safet y f eatures to pr otect bot h you and the serv ice tec hnician ...
-
Taylor C717 - page 10
6 Mo del s C709 & C717 Safety 130228 S Supply cor ds used with this unit shall be oil-res istant , s heathed f lexible cable not lighter than ordinar y polyc hloroprene or other equivalent sy nthet ic elastom er-s heathed cor d (Code designat ion 60245 IEC 57) inst alled with t he proper c ord anchorage t o relieve c onductor s fr om st rain, i ...
-
Taylor C717 - page 11
7 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n 100324 Section 4 Operator Parts Identif ication Model C709 Figur e 1 ITE M DESCRIPTI ON PART NO. 1 PANEL-SI DE-LEFT 056963- SP1 2 PAN-DRI P 11-5/ 8 LONG 027503 3 PIN- RETAINING- HOPPER CVR 043934 4 KIT A. -COVER-HOPPER X65368 5 BLADE A.- AGITATOR X56591 6 TUBE A.- FEED-OUTER- HT X34641 ...
-
Taylor C717 - page 12
8 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n Model C709 S ingle Spout D oor and Beater Assem bly Figur e 2 ITE M DESCRIPTI ON P ART NO. 1 HANDLE A.- DRAW-WELDED X56246 2 O-RI NG-1/ 4 OD X .070W 50 015872 3 SCREW-ADJUSTMT- 5/16- 24 056332 4 NUT-STUD BLACK 3. 250” 058765 5 NUT-STUD BLACK 2. 563“ 058764 6 DOOR A.- W/BAFFLE X5733 ...
-
Taylor C717 - page 13
9 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n 130129 Model C717 Figur e 3 ...
-
Taylor C717 - page 14
10 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n 130128 Model C717 Exploded View Par ts Identificatio n ITE M DESCRIPTI ON PART NO. 1 COVER-HOPPER 053809- 1 2 BLADE A.- AGITATOR X56591 3 OR IFICE 022465-100 4 TUBE A.- FEED-SC- INNER-3/ 16 X32824-3 5 TUBE A.- FEED-OUTER- HT X34641 6 O-RI NG-. 643 OD X . 077 W 018572 7 PANEL-REAR 0599 ...
-
Taylor C717 - page 15
11 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n 140121 Model C717 Thr ee Spout D oor and Beater Assem bly Figur e 4 ITE M DESCRIPTI ON PART NO. 1 DOOR A.- 3SPT*HT* LG BAF X59923-SER 1a BA FF LE A .-LO NG 4 IN W /RA D X50882 2 HANDLE A.- DRAW-WELDED X56421-1 3 O-RI NG-1/ 4 OD X .070W 50 015872 4 SCREW-ADJUSTMENT- 5/16- 24 056332 5 V ...
-
Taylor C717 - page 16
12 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n Feed Tube Assem bly Figur e 5 ITE M DESCRIPTI ON PART NO. 1 AIR ORI FICE 022465-100 1a O-RI NG 016137 2 TUBE A.- FEED-SC-I NNER (C709) X32824- 2 TUBE A.- FEED-SC-I NNER (C717) X32824- 3 ITE M DESCRIPTI ON PART NO. 3 O-RI NG - . 291 ID x .080 W 018550 4 TUBE A.- FEED-OUTER- HT X34641 5 ...
-
Taylor C717 - page 17
13 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n 140718 Accessor ies Figur e 6 ITE M DESCRIPTI ON PART NO. 1 PAIL- 10 QT. 013163 2 TOOL-O- RING REMOVAL 048260-W HT 3 LUBRICANT- TAYLOR HI- PERF 048232 ITE M DESCRIPTI ON PART NO. *4 SANITI ZER KAY-5 25 PACKS SEE NOTE **5 KIT A. -TUNE- UP (C709) X49463-92 KIT A. -TUNE- UP (C717) X49463 ...
-
Taylor C717 - page 18
14 Mo del s C709 & C717 Op erato r Parts I den ti ficat io n Br ushes Figur e 7 ITE M DESCRIPTI ON PART NO. 1 BRUSH-REAR BRG 1” D X 2 ” L 013071 2 BRUSH-DOUBLE ENDED 013072 3 BRUSH-DRAW VALVE 1” OD X 2 013073 ITE M DESCRIPTI ON PART NO. 4 BRUSH-MI X PUMP BODY 3” X 7” 023316 5 BRUSH-END- DOOR-SPOUT-SS 039719 ...
-
Taylor C717 - page 19
15 Models C 70 9 & C7 17 Impor tant : To the Opera tor 130228 Section 5 Important: To the Operator Figur e 8 ITE M DESCRIPTI ON 1 POWER SWITC H 2 LIQUI D CRYSTAL DISPLAY 3 KEYPADS 4 MIX OUT I NDICATOR 5 STANDBY KEY 6 MIX LOW INDI CATOR 7 SELECT KEY 8 SERVICE MENU KEY 9 BRUSH CLEAN COUNTER 10 ARROW KEYS 11 TOPPING HEATER KEY ...
-
Taylor C717 - page 20
16 Mo del s C709 & C717 Impor tant : To the Opera tor 130228 Sym bol Defi nitions To bet ter comm unicate in t he Int ernat ional arena, sym bols have replac ed words on many of our operat or switches , funct ion, and fault indicat ors. Your T aylor equipm ent is des igned with t hese Int ernat ional symbols . The f ollowing chart identif ies t ...
-
Taylor C717 - page 21
17 Models C 70 9 & C7 17 Impor tant : To the Opera tor 130819 IMP ORT ANT: Make su re the l evel o f mi x in th e hopper is be low the mix deliv er y hole in the fee d tube. Failure to f ollow this inst ruct ion may res ult in lower produc t qualit y when normal oper ation is resume d. To r esume norm al operation, pres s t he AUTO symbol . Whe ...
-
Taylor C717 - page 22
18 Mo del s C709 & C717 Impor tant : To the Opera tor Operating S creen D escriptions The f luoresc ent display locat ed in the cent er of the contr ol panel is normally blank during the daily operation of t he machine. The dis play is act ivat ed when the SE L sym bol or the M anager's Menu is select ed. T he display s creen will also ale ...
-
Taylor C717 - page 23
19 Models C 70 9 & C7 17 Impor tant : To the Opera tor If Lock out Data is corrupt ed, all lockout hist ory data is cleared. A “LO CKOUT CRC ERR” fault is displayed. Aft er t he memory int egrity has been t est ed, the Safet y T imeout scr een will be displayed. Heat Cycl e Data Heat cycl e data is checked s eparately f rom t he rest of t h ...
-
Taylor C717 - page 24
20 Mo del s C709 & C717 Impor tant : To the Opera tor 140303 Use the up or down arrow s ymbol t o move t he cursor to “YES”. Touch the SEL symbol to immediately s t art a heat cycle. Note: T he mac hine must be in AUT O or S TANDB Y and have suf fic ient mix in the hopper befor e the machine c an succes sfully enter the HEA T m ode of opera ...
-
Taylor C717 - page 25
21 Models C 70 9 & C7 17 Impor tant : To the Opera tor Touching t he SE L symbol will dis play the f ollowing scr een. FREEZER LOCKED 2. The f ollowing scr een will display if ther e has been a ther mist or failur e (f reezing cy linder or hopper) dur ing the heat tr eatment proc ess. SYSTEM FAULT FREEZER LOCKED SERVICE REQ'D > WASH TO ...
-
Taylor C717 - page 26
22 Mo del s C709 & C717 Impor tant : To the Opera tor 130228 A sof t loc k can also oc cur any time dur ing operat ion when the hopper or fr eezing cy linder tem peratur e rises above 59°F (15° C), the t emperat ure ris es and remains above 45°F (7° C) for more t han one hour, or the t emperat ure ris es and rem ains above 41°F (5° C) for ...
-
Taylor C717 - page 27
23 Models C 70 9 & C7 17 Impor tant : To the Opera tor 140131 Ther e is a two m inute t ime-out in eff ect during t he Manager' s Menu. While in t he Manager' s Menu, if no acti vity occur s within a t wo minut e period, t he display will ex it t o the Main M enu. T here is one except ion to t his t ime-out , and t hat is the Cur rent ...
-
Taylor C717 - page 28
24 Mo del s C709 & C717 Impor tant : To the Opera tor 140131 Reset t he SE RVING S CO UNTER by touc hing the SEL s ymbol t o advance t o the nex t sc reen. T ouch the UP arrow symb ol to move the arrow (>) to YES and touch t he SE L symbol. T he servings count er will reset to z ero and exit back to t he Manager' s Menu. RESET COUNTERS ...
-
Taylor C717 - page 29
25 Models C 70 9 & C7 17 Impor tant : To the Opera tor Pres sing the UP or DO WN sy mbol will move t he arrow t o the appr opriate week for the s tart of DST . Pres sing the S EL sym bol next to t he appropriat e week will display the f ollowing screen. Pr ess t he UP or DO WN sy mbol to m ove t he arrow t o the appropriat e mont h for t he end ...
-
Taylor C717 - page 30
26 Mo del s C709 & C717 Impor tant : To the Opera tor Use the ar row sy mbols t o program the AUT O STA RT T IM E by incr easing or dec reasing t he hour set ting above t he curs or. Touch t he SE L symbol t o advance t he curs or and program the m inutes set ting. Touc h the SE L symbol t o ret urn t o the previous screen wit h t he new time s ...
-
Taylor C717 - page 31
27 Mode ls C70 9 & C7 17 Impor tant : To the Opera tor 140303 Fault H istor y The F AULT HIST ORY will display up t o 100 f aults that have occur red. T he most recent f ault is displayed on sc reen 1. The dat e, t ime, and fault descr iption is dis played on each sc reen. F AUL T HISTOR Y 1 00/00/ 00 00:00 REASON >E x i t Lockout H istor y ...
-
Taylor C717 - page 32
28 Mo del s C709 & C717 Impor tant : To the Opera tor 051025 Faults Occ urring While i n AUTO Mode (L/ R) HP R>41F (5C) AF TE R 4 HR - The mi x tem peratur e in the hopper was above 41°F (5° C) more t han four hours. (L/ R) BRL >41F (5C) AFT ER 4 HR - The mix tem peratur e in the f reezing cy linder (bar rel) was above 41°F (5° C) mor ...
-
Taylor C717 - page 33
29 Mode ls C70 9 & C7 17 Impor tant : To the Opera tor 140303 The t hird sc reen shows t he right side (R) of t he fr eezer. The t op line of t hese sc reens shows the hopper (H) and barrel ( B) t emperat ures r ecorded at the end of the Heat Tr eat Cy cle and indicat es the s ide (L or R) of t he fr eezer. The r emaining lines indicat e the f ...
-
Taylor C717 - page 34
30 Mo del s C709 & C717 Impor tant : To the Opera tor 120227 System Inform ation The SYSTEM I NFORMATION is displaye d on three separat e scr eens. T he f irst scr een contains the contr ol and sof tware v ersion ins talled in t he machine. SOFTW ARE VERSION C709 CONTROL UVC VERSION X. XX > Next Touc h the SE L symbol t o advanc e to t he ne ...
-
Taylor C717 - page 35
31 Mo del s C709 & C717 Op erati ng Pro cedu res Section 6 Operating Procedures The C709 m achine st ores mix in a hopper. It has a 3.4 quart (3. 2 liter ) capac ity f reezing c ylinder wit h a single spout door. The C717 m achine st ores mix in two hopper s. I t has two 3. 4 quart (3.2 lit er) capacit y f reezing cy linders with a t hree spout ...
-
Taylor C717 - page 36
32 Mo del s C709 & C717 Op erati ng Pro cedu res Step 3 Tak e one of t he scraper blades and slip it under t he hook at the f ront of t he beater . W rap the blade around t he beater f ollowing the helix and pushing the blade down ont o the helix as you wr ap. At t he back end of the beat er, slip t he blade under t he hook. Rep eat th is step ...
-
Taylor C717 - page 37
33 Mo del s C709 & C717 Op erati ng Pro cedu res Mo del C709 Freez er Doo r Assembl y (Cont'd.) Step 2 Slide the t hree o- rings int o the groov es on t he draw valve and lubr icate. (S ee Figure 17. ) Figur e 17 Step 3 Lightly lubr icat e the inside of t he top of the f reezer door valv e cavit y. ( See Figur e 18.) Figur e 18 Step 4 Inse ...
-
Taylor C717 - page 38
34 Mo del s C709 & C717 Op erati ng Pro cedu res 140121 Mo del C709 Freez er Doo r Assembl y (Cont'd.) Note: T he C709 f eatures an adjust able draw handle to pr ovide port ion contr ol, givi ng a bett er consis tent quality t o your product and cont rolling cos ts. The dr aw handle should be adjust ed to prov ide a flow r ate of 5 to 7- 1 ...
-
Taylor C717 - page 39
35 Mo del s C709 & C717 Op erati ng Pro cedu res Step 3 Ins ert t he baff le rods t hrough t he beater s in the fr eezing cylinder s. W it h the door s eated on t he fr eezer st uds, inst all the handsc rews, with t he longer ones on top. T ighten equally in a cris s-cr oss pat tern to insur e the door is snug. Figur e 26 Step 4 Slide the t hre ...
-
Taylor C717 - page 40
36 Mo del s C709 & C717 Op erati ng Pro cedu res 140121 Mo del C717 Freez er Doo r Assembl y (Cont'd.) Step 8 Slide the piv ot pin t hrough t he draw handles as t he handles are ins erted int o the dr aw valves . Figur e 30 Note: T his f reezer f eatures adjus table draw handles to pr ovide port ion contr ol, givi ng a bett er consis tent ...
-
Taylor C717 - page 41
37 Mo del s C709 & C717 Op erati ng Pro cedu res 080227 Step 2 Slide the t wo o-r ings into t he grooves of t he outer feed t ube. Figur e 34 Step 3 Slide the s mall o-r ing into t he groove of the air orific e. Figur e 35 Note: M ake sur e the hole in t he air orif ice is c lean and is not clogged. I f the hole in t he air orif ice should beco ...
-
Taylor C717 - page 42
38 Mo del s C709 & C717 Op erati ng Pro cedu res 130228 Step 3 While t he solut ion is flowing int o the f reezing cylinder , t ake part icular car e to br ush-clean t he mix level sens ing probe on the bot tom of t he hopper, the mix hopper , t he mix inlet hole, and t he feed t ubes. Step 4 Place t he power swit ch in t he ON posit ion. Step ...
-
Taylor C717 - page 43
39 Mo del s C709 & C717 Op erati ng Pro cedu res 140718 Step 10 Stand t he ass embled feed t ube in the c orner of the mix hopper and place the agit ator on the agit ator housing. Figur e 41 Step 11 Retur n to t he freez er with a s mall amount of sanitiz ing solut ion. Dip t he door spout brush int o the sanitiz ing solut ion and brush clean t ...
-
Taylor C717 - page 44
40 Mo del s C709 & C717 Op erati ng Pro cedu res 140722 Daily Closing Procedures This proce dure must be performed once daily! The f unct ion of t he Heat T reat ment Cy cle is t o destr oy bact eria by r aising the t emper ature of t he mix in t he fr eezing cylinder and the hopper to a specif ied tem peratur e for a s pecified per iod of t im ...
-
Taylor C717 - page 45
41 Mo del s C709 & C717 Op erati ng Pro cedu res 080227 Step 9 Replace the hopper cover (s) and install t he drip pans. Step 10 Retur n to t he freez er with a s mall amount of cleaning solut ion. Dip t he door spout brus h into t he cleaning solut ion and brush c lean the door s pout(s ) and bott om of the draw v alve(s ). Note: T o ass ure sa ...
-
Taylor C717 - page 46
42 Mo del s C709 & C717 Op erati ng Pro cedu res 130228 Step 3 Retur n to t he freez er with a s mall amount of sanitiz ing solut ion. Dip t he door spout brush int o the sanitiz ing solut ion and brush clean t he door spout (s) and bott om of the draw v alve(s ). Figur e 46 Note: T o ass ure sanit ary condit ions are m aintained, brush c lean ...
-
Taylor C717 - page 47
43 Mo del s C709 & C717 Op erati ng Pro cedu res 130228 Dr aining P roduct Fr om The Freez ing Cylinder Step 1 Pres s the A UTO sym bol , canc elling compres sor and beater mot or operat ion. Step 2 Remove t he hopper cov er, t he agitat or paddle, and the ass embled f eed tube. Tak e these par ts t o the sink for c leaning. Step 3 Wit h a pail ...
-
Taylor C717 - page 48
44 Mo del s C709 & C717 Op erati ng Pro cedu res 080227 Step 3 Open t he draw valv e on the f reezer door . Dr ain all the r inse water fr om the door spout , clos e the draw valve and t ouch t he WAS H symbol, / cancelling the W ash mode. Step 4 Repeat this proc edure using clean, warm water, unt il the wat er being disc harged is clear . Repe ...
-
Taylor C717 - page 49
45 Mo del s C709 & C717 Op erati ng Pro cedu res 080227 Br ush Cleaning Step 1 Prepar e an approved 100 PP M cleaning solut ion (exam ples: 2-1/ 2 gal. [9.5 liters ] of Kay-5 R or 2 gal. [7. 6 liters] of S tera- Sheen R ). USE WARM WAT ER A ND FO LLOW THE MANUF ACTURE R'S SPECIFICATIO NS. Make sure all b rushes pro vided with t he fr eezer ...
-
Taylor C717 - page 50
46 Mo del s C709 & C717 Impor tant : Opera tor C hec klis t 121008 Section 7 Important: Operator Checklist Dur ing Br ush Cleani ng and Sani tizing ALWAYS FOLLOW LOCAL HEALTH CODES. Clean in g and san it iz in g sched ul es are g o verned by your Fe der al, Sta te or loca l regula tor y agen cies an d mu st b e fo ll ow ed acco rdi ng l y. Plea ...
-
Taylor C717 - page 51
47 Models C 70 9 & C7 17 Impor tant : Opera tor C hec klis t 080128 j 7. If your m achine is equipped wit h an auxiliary refrigerat ion syst em, check t he auxiliary condenser for ac cumulat ion of dir t and lint . Dirty condenser s will reduc e the ref rigerat ion capacit y of t he mix hopper. Condenser s must be cleaned monthly with a sof t b ...
-
Taylor C717 - page 52
48 Mo del s C709 & C717 Trouble shooting Guide 061204 Section 8 Troubleshooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 1. Sof t lock m essage appears on dis play. a. More t han 24 hours sinc e the last HEAT cycle. a. The f reezer m ust go t hrough a HEAT cycle eve ry 24 hours. The f reezer must now be disass embled and brush cleaned or ...
-
Taylor C717 - page 53
49 Models C 70 9 & C7 17 Trouble shooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 3. No produc t is being dispensed. a. Low on mix . T he MIX OUT light is on. a. A dd mix t o the m ix hopper. Retur n to AUT O m ode. 39 b. T he power s witch is in the OF F posit ion. b. P lace t he power swit ch to O N and se lect AUTO. 38 c. The c ircuit ...
-
Taylor C717 - page 54
50 Mo del s C709 & C717 Trouble shooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 5. T he product is t oo thick . a. F reez ing cylinder not primed co rrectly. a. Dr ain the f reezing c ylinder and reprim e the mac hine. 39 b. The visc osity c ontrol is set too cold. b. Call an authoriz ed serv ice technic ian. --- c. Fr eeze-up in mix in ...
-
Taylor C717 - page 55
51 Models C 70 9 & C7 17 Trouble shooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 12. The driv e shaft is s tuck in the dri ve coupling. a. Mix and lubricant collec ted in drive c oupling. a. Br ush clean t he rear s hell bearing area r egularly. 45 b. Rounded corners of dr ive shaft , driv e coupling, or both. b. Call an authoriz ed ser ...
-
Taylor C717 - page 56
52 Mo del s C709 & C717 Parts Rep lacemen t Sch edu l e 060515 Section 9 Part s Replacement Schedule PART DESCRIPTI ON EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Scr aper Blades X Drive S haft Seal X Fr eezer Door Gas ket X Fr ont Bearing X Draw Valve O -Ring X Mix F eed Tube O -Ring X Air Ori fic e O-Ri ng X Whit e Bris tle Br ush, 3” x 7” Ins ...
-
Taylor C717 - page 57
53 Models C 70 9 & C7 17 Limite d Warr ant y on Equipment 131 121 Section 10 Limited Warranty on Equipment TAYL OR CO MP ANY LI MI TED W ARRANTY ON F REEZ ERS Tayl or Company, a divis ion of Carr ier Comm ercial Ref rigerat ion, I nc. (“T aylor” ) is pleased t o prov ide this lim ited warrant y on new T aylor-br anded fr eezer equipment ava ...
-
Taylor C717 - page 58
54 Mo del s C709 & C717 Limite d War ra nty on Equipme nt 3. Replacement of wear it ems designat ed as Class “000” part s in the Tay lor Operat or’s M anual. 4. Ext ernal hoses , elect rical power supplies, and mac hine grounding. 5. Part s not supplied or designat ed by Taylor , or damages res ulting fr om their us e. 6. Return t rips or ...
-
Taylor C717 - page 59
55 Mo del s C709 & C717 Li mit ed W arranty o n Parts 131 121 Section 11 Limited W arranty on Parts TAYL OR CO MP ANY LI MI TED W ARRANTY ON T AYL OR G ENUINE PART S Tayl or Company, a divis ion of Carr ier Comm ercial Ref rigerat ion, I nc. (“T aylor” ) is pleased t o prov ide this lim ited warrant y on new T aylor genuine replac ement com ...
-
Taylor C717 - page 60
56 Mo del s C709 & C717 Li mit ed W arranty o n Parts LI MI TED W ARRANTY EXCEP TI ONS This limit ed warrant y does not cover: 1. Labor or other cos ts inc urred for diagnos ing, repairing, rem oving, inst alling, s hipping, serv icing or handling of defec tive Part s, replac ement Par ts, or new Part s. 2. Normal m aintenance, cleaning and lub ...
-
Taylor C717 - page 61
57 Mo del s C709 & C717 Li mit ed W arranty o n Parts LI MI TAT IO N OF WARRANT Y THI S LI MI TE D WARRANT Y IS EXCL USI VE AND I S IN L IE U OF ALL OT HER W ARRANTI ES, CONDI TI ONS AND/O R REMEDI ES UNDER T HE LAW , INCL UDING ANY I MPL IED W ARRANTI ES OR CO NDIT IO NS OF MERCHANT ABIL IT Y O R FI TNES S FO R A PART ICUL AR PURPO SE. THE ORI ...
-
Taylor C717 - page 62
Mod e l C709 057010-27 06/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c JP6 NO JP7 JUMPER INSTALLED DISABLES RESET. NO RTCK RESERVED (DO NOT USE) NO DBGEN RESERVED (DO NOT USE) NO W1 RESERVED (DO NOT USE) NO JUMPER INSTALLED-FORCE BRUSH CLEAN STATUS. JUMPER INSTALLED-OPEN ALL SOLENOIDS. RESERVED (DO NOT USE) W6 JUMPER INSTALLED-RE ...
-
Taylor C717 - page 63
Mod e l C709 057010-33 06/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c BROWN J2 J3 GND +5V J5 1 2 3 4 5 6 J6 1 2 3 4 5 6 L1 7 J7 1234567 3 1 5 J8 J9 J12 J11 1 2 3 4 5 6 7 8 J10 1 2 3 4 5 6 7 8 9 10 B A J14 INTFC PCB A. WITH SOFT SERVE PERSONALITY PCB A. 7 8 J13 RED WHT/RED ON OFF BARREL LIQUID SOLENOID HOPPER LIQUID SOLENOID WHT/ ...
-
Taylor C717 - page 64
Mod e l C709 057010-40 06/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c J2 J3 GND +5V J5 123456 J6 1 2 3 4 5 6 L1 7 J7 1234567 3 1 5 J8 J9 J12 J11 1 2 3 4 5 6 7 8 J10 1 2 3 4 5 6 7 8 9 10 B A J14 INTFC PCB A. WITH SOFT SERVE PERSONALITY PCB A. 7 8 J13 RED WHT/RED ON OFF BARREL LIQUID SOLENOID HOPPER LIQUID SOLENOID WHT/ORN 14 13 B ...
-
Taylor C717 - page 65
Mod e l C709 057010-58 06/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c J2 J3 GND +5V J5 1 2 3 4 5 6 J6 123456 L1 7 J7 1234567 3 1 5 J8 J9 J12 J11 1 2 3 4 5 6 7 8 J10 1 2 3 4 5 6 7 8 9 10 B A J14 INTFC PCB A. WITH SOFT SERVE PERSONALITY PCB A. 7 8 J13 RED WHT/RED ON OFF BARREL LIQUID SOLENOID HOPPER LIQUID SOLENOID WHT/ORN 14 13 B ...
-
Taylor C717 - page 66
Mod e l C717 059901-27 07/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c RESERVED (DO NOT USE) EXTERNAL GROUND L2 L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH DPDT BLK ON OFF RED BLU GR ...
-
Taylor C717 - page 67
Mod e l C717 059901-33 07/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c RESERVED (DO NOT USE) EXTERNAL GROUND L2 L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH 3PDT BLK ON OFF RED BLU GR ...
-
Taylor C717 - page 68
Mod e l C717 059901-40 07/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c RESERVED (DO NOT USE) EXTERNAL GROUND N L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH DPDT BLK ON OFF RED BLU GRN ...
-
Taylor C717 - page 69
Mod e l C717 059901-58 07/14 Taylor Company 2014 Carrier Commercial Refrigeration, Inc. c RESERVED (DO NOT USE) EXTERNAL GROUND N L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH DPDT BLK ON OFF RED BLU GRN ...
¿Tienes una pregunta acerca de Taylor C717?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Taylor C717, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Taylor C717 probablemente compartirá una forma de solucionarlo.