-
Exmark AS - page 1
UL TRA V AC ® LAZER Z ® , LAZER Z ® AS, LAZER Z ® XP AND LAZER Z ® XS MODELS For Ultra V ac Serial Nos. 850,000 & Higher (to t Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999) (to t Lazer Z XS Units 352,000 & Higher) Part No. 4500-610 Rev . A ...
-
Exmark AS - page 2
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y . Exmark, or its distributors and dealers, accept no responsibility f or v ariations which may be evident in the actual specications of its products and the state ...
-
Exmark AS - page 3
Introduction CONGRATULATIONS on the purchase of your Exmark Ultra V ac. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance, adjustment, and safety instr uctions for y our Exmark Ultra V ac BEFORE OPERATING Y OUR ...
-
Exmark AS - page 4
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 5 Safety Alert Symbol . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . ...
-
Exmark AS - page 5
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1. Safety alert symbol The safety alert symbol appears abov e infor ...
-
Exmark AS - page 6
Safety collection system or mulch kit in place and w orking properly . DANGER There are rotating blades in the blo wer and under the mow er deck. Blade contact can cause serious operator or bystander injur y or ev en death. • Do Not reach into blo wer unless rotation indicator has stopped. Disengage PT O , stop engine, remo ve k ey , wait for all ...
-
Exmark AS - page 7
Safety Figure 3 1. Safe Zone-Use the mower here on slopes less than 15 degrees 2. Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water . 3. Water • Remo v e or mark obstacles such as roc ks , tree limbs , etc. from the mowing area. T all g rass can hide obstacles . • W atc h for dit ...
-
Exmark AS - page 8
Safety Safety and Instructional Decals • Keep all safety signs legible. R emov e all grease, dirt and debris from safety signs and instr uctional labels . • Replace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components . • If an ...
-
Exmark AS - page 9
Safety 103-3508 LZUV52 Only 109-5890 UV60 and UV6672 9 ...
-
Exmark AS - page 10
Specications Specications Model Numbers Serial Nos: 850,000 and Higher LZUV52–Fits Lazer Z (LZ) and Lazer Z AS (LAS) Units 789,999 and Lo wer with 52 inch dec k. UV60–Fits Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999 and Lazer Z XS Units 352,000 and Higher with 60 inch deck. UV6672–Lazer Z (LZ), Lazer Z AS (LAS ...
-
Exmark AS - page 11
Specications Overall Length: w/Ultra V ac 52 inch Deck-Air -Cooled 105.70 inches (268.5 cm) 52 inch Dec k- Liquid-Cooled 106.00 inches (269.1 cm) 60 inc h Dec k-SN 599,999 and Low er Air -Cooled 106.65 inches (270.9 cm) 60 inch Dec k-SN 600,000–789,999 Air-Cooled 110.04 inches (279.5 cm) 60 inc h Dec k-SN 599,999 and Low er Liquid-Cooled 106.9 ...
-
Exmark AS - page 12
Operation Product Overview Figure 4 1. Hood 4. Tube 2. Weight 5. Bag 3. Blower Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start Make sure you understand the controls , their locations , their functions , and their safety requirements . Ensure the blow er , belt cov er , bags , tube an ...
-
Exmark AS - page 13
Operation hav e stopped before clearing blow er assembly or mow er dec k 3. T o remo v e the bags , rst shut off dec k dri ve , stop the engine and wait for all moving parts to stop . Open the hood and remov e the bags b y lifting up on the rear of the bag, then unhooking the front clip . Empty the bags b y inv erting them. 4. R einstall bags , ...
-
Exmark AS - page 14
Operation Figure 6 Viewed from the right side 1. Hairpin 3. Discharge Chute 2. Chute Pivot Pin Note: Install chute with the tabs to the rear of the deck tabs as sho wn. W ARNING An unco v ered discharge opening will allow objects to be thrown in operator’s or bystander’s direction. Also, contact with blade could occur . Thrown objects or blade ...
-
Exmark AS - page 15
Operation 6. Pull the spring loaded idler bac k and slip the belt ov er the top spindle deck sheav e . 7. Install the plastic belt cov er . On 60 inc h and 66 inch units the outside end of the cov er is slotted and can slip betw een the tw o washers on the belt shield stud. The plastic knob does not need to be remov ed. On 72 inc h and 52 inch unit ...
-
Exmark AS - page 16
Operation T ransporting T ransporting a Unit Use a hea vy-duty trailer or truck to transport the machine . Loc k brak e and block wheels . Securely fasten the machine to the trailer or tr uck with straps , chains , cable , or ropes . Be sure that the trailer or tr uc k has all necessar y lighting and marking as required by law . Secure a trailer wi ...
-
Exmark AS - page 17
Operation minimize the ramp angle . The trailer or truck should be as lev el as possible . Important: Do Not attempt to tur n the unit while on the ramp , y ou may lose control and driv e off the side. A v oid sudden acceleration when driving up a ramp and sudden deceleration when backing do wn a ramp . Both maneuv ers can cause the unit to tip bac ...
-
Exmark AS - page 18
Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders. Remo ve the k ey from the ignition s witch, engage parki ...
-
Exmark AS - page 19
Maintenance Lubricate Grease Fittings Note: See char t for ser vice inter v als. 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engage parking brake . 2. Lubricate ttings with NGLI g rade #2 multi-purpose gun grease. R efer to the following chart for tting locations and lubrication sc hedule. Lubrication Char t Fittin ...
-
Exmark AS - page 20
Maintenance Cleaning Clean Mufer and Rear Frame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop , and remov e key . Engag e parking brak e. W ARNING Operating engine parts, especiall y the mufer, become extremely hot. Sev ere bur ns can occur on contact and de bris, such as leav es, grass, br ush ...
-
Exmark AS - page 21
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , Do Not o verlook the simple causes . F or example: starting problems could be caused b y an empty fuel tank. The follo wing table lists some of the common causes ...
-
Exmark AS - page 22
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair , replace or adjust any part on these products and found by us (in the ex ercise of our reasonable discretion) to be defective in factory ...
-
Exmark AS - page 23
G01 1841 Figure 10 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees . Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. ...
-
Exmark AS - page 24
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM RIDE SEA T SUSPENSION SYSTEM FULL SUSPENSION SEA T DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT 12 V PO WER POR T MICRO-MULCH SYSTEM OPERA T OR CONTROLLE ...
¿Tienes una pregunta acerca de Exmark AS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Exmark AS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Exmark AS probablemente compartirá una forma de solucionarlo.