-
Eagle A100 - page 1
EA GLE I n s t a l l a t i o n, Op er a t i on an d M a in t en an c e I n s tru c ti o ns EA G L E M O D E L A 1 00 A N S I P U M P S Lubrication information is in Section III-A, Item 1b. and Section IV -A. ...
-
Eagle A100 - page 2
2 SECTION I—GENERAL Introduction ................................................................................................................................................................. 3 I-A Importance of Instructions ........................................................................................................................ ...
-
Eagle A100 - page 3
3 Introduction This instruction manual is intended to assist those involved with the installation, operation and maintenance of Eagle Model A100 pumps. It is recommended that this manual be thoroughly reviewed prior to installing or performing any work on the pump or motor . I-A. Impor tance of Instr uctions The design, material and workmanship inc ...
-
Eagle A100 - page 4
4 II-C. Lev eling and Gr outing of Baseplate Initial Alignment Chec k 1. Put the unit in place on wedges located at four points as shown in F ig . 2. Some long installations may require additional wedges near center of bedplate. 2. Adjust wedges to level unit (appro ximately), placing unit between ” and 1” above foundation. Level or plumb ...
-
Eagle A100 - page 5
5 PRIOR TO COUPLING DRIVER TO PUMP , ROT A TION OF DRIVER SHOULD BE CHECKED! Serious damage can result if pump is rotated in wrong direction. Once motor rotation is checked, connect coupling , following the manufacturer ’s instructions. If a coupling guard is furnished with the unit, ensure that it is securely fastened in place. II-F . Stufng ...
-
Eagle A100 - page 6
6 b. A high quality turbine type oil with rust and oxidation inhibitors should be used. Under normal operating conditions, an oil of 300 SSU viscosity at 100° F . (approximately SAE 20) should be used. Fill oiler bottle and replace in oiler housing . Repeat until oil remains visible in bottle. Do not add oil through the vent or breather . Optional ...
-
Eagle A100 - page 7
7 SECTION V— DIS ASSEMBL Y AND REASSEMBL Y V -A. Disassembly (refer to Sectional V iews in Part VI) 1. Prepare pump for disassembly as follows: a. Lock out power supply to motor . b. Shut off valves controlling flow to and from pump. c. Flush pump of all corrosive or toxic liquid, if required. d. Remove all auxiliary tubing and piping . e. Discon ...
-
Eagle A100 - page 8
8 4. On S, M and L models, insert retaining ring (361A) into groove in bearing housing (134A). Flat side of retaining ring must be against bearing (112A). On X units, slide bearing end cover (109A) and gasket (360C) on shaft. Ensure the “top ” of end cover (109A) lines up with the “top ” of bearing housing (134A), check scribe marks. If the ...
-
Eagle A100 - page 9
9 13. Place casing gasket (351) against shoulder in casing . 14. Slide the pullout assembly into the casing (100). Drain slot in stuffing box cover (184) should line up with drain connection in casing. Install frame–to–casing bolts (370) and tighten evenly while rotating shaft (122) by hand. If impeller ceases to turn freely , stop tightening o ...
-
Eagle A100 - page 10
10 101 106 1 12A 126 168A 261 332A 333A 351 360C 360D 412A 469D 496 1 1 set 1 1 1 1 1 1 1 1 1 1 1 1 Impeller Stuffing Box Packing (2) Ball Bearing-Outboard. Shaft Sleeve Ball Bearing-Inboard Mechanical Seal Gland Gasket (3) Oil Seal-Outboard Oil Seal-Inboard Gasket-Casing Gasket-Bearing End Cover-Bearing Housing Gasket-Bearing Frame-Adaptor (not sh ...
-
Eagle A100 - page 11
11 Mod el A 1 0 0 S, M, L Ass embl y Vie w of 8” P umps Only 100 239 105 106 412A 469D 101 351 122A 355 353 107 333A 370D 1 13A 496 361A 168A 123 210 261 126 370H 184 370 228A 1 12A 134A 332A 136 & 382 370C 370 503 ...
-
Eagle A100 - page 12
12 Mod el A 1 0 0 M , L 132 370 184 168A 360D 496 108 107 355 353 123 113A 228A 370C 134A 136 & 382 332A 112A 370D 361A 370E 370H 126 122A 210 333A 106 370F 131 239 105 469D 412A 106 101 351 100 ...
-
Eagle A100 - page 13
13 Mod el A 1 0 0 X 101 412A 469D 106 105 184 351 100 370H 239 355 107 370 370E 131 228A 370F 106 333A 469B 353 1 13A 168A 123 261 126 108 210 132 122A 360D 370D 371C 109A 332A 136 & 382 496A 134A 1 12A 496 ...
-
Eagle A100 - page 14
14 Causes & Corrective Measures 1. Pump not primed or properly vented—check that casing and suction pipe are completely filled with liquid. 2. Speed too low—check whether motor wiring is correct and receives full voltage or turbine receives full steam pressure. 3. System discharge head too high—check system head (particularly friction los ...
-
Eagle A100 - page 15
15 SEC T ION VII I — ORDERI NG S P ARE P ART S VIII-B. Instr uctions for Or dering Spare Par ts Repair orders will be handled with the minimum of delay if the following directions are followed: 1. Give model number , size of pump, and serial number . These can be obtained from the nameplate on the pump. 2. W rite plainly the name, part number , a ...
-
Eagle A100 - page 16
EA GLE EA GL E P UMP & C OM P RE SSO R L T D . 7025 - 5 Street S.E., Calgar y , AB T2H 2G2 Canada ANSI Centrifugal Pumps Multistage Horizontal Pumps V er tical Sump Pumps R otar y Scr ew Compressor Air/Gas Dr y er s www .ea g le-pc.com Printed in Canada 01/2000 ...
¿Tienes una pregunta acerca de Eagle A100?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Eagle A100, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Eagle A100 probablemente compartirá una forma de solucionarlo.