-
Zenoah G500AVS - page 1
G455A VS / G500A VS G B GB-1 G455AVS G500AVS OWNER’S MANUAL CHAIN SA W G B 848C8193A4 (806) ...
-
Zenoah G500AVS - page 2
G455A VS / G500A VS GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book before operating this machine. W ear head, ey e and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickback. Read, understand and follow all warnings. W ARNING!!! RISK OF D AMA GING HEARING W ear head, eye and ear prot ...
-
Zenoah G500AVS - page 3
G455A VS / G500A VS G B GB-3 Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 7 4. Fuel and Chain Oil ...................................... ...
-
Zenoah G500AVS - page 4
G455A VS / G500A VS GB-4 1. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medica- tion that may make you drowsy , or if you are under the influence of alcohol or drugs. 2. Use safety footwear , snug fitting clothing and eye, hearing and head protection devices. Use the vibration-proo ...
-
Zenoah G500AVS - page 5
G455A VS / G500A VS G B GB-5 17. Use extreme caution when cut- ting small size brush and sap- lings because slender material may catch the saw chain and be whipped toward you or pull you off balance. 18. When cutting a limb that is un- der tension, be alert for spring- back so that you will not be struck when the tension in the wood fibers is relea ...
-
Zenoah G500AVS - page 6
G455A VS / G500A VS GB-6 2. Explanation of Symbols on the Machine W ARNING • For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The screw under the “H” stamp is The High-speed adjustment scr ew . The port to refuel “MIX GASOLINE” Posit ...
-
Zenoah G500AVS - page 7
G455A VS / G500A VS G B GB-7 Power unit Bar protector Guide bar Saw chain Plug wrench Screwdriver for carburetor adjustment 5. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 6. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side ...
-
Zenoah G500AVS - page 8
G455A VS / G500A VS GB-8 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool bef ore refuel- ing the unit. Select outdoor bare gr ound for fuel- ing and move at least 3 m (10 ft) a wa y from the fueling point before starting ...
-
Zenoah G500AVS - page 9
G455A VS / G500A VS G B GB-9 W ARNING •K eep clear of the sa w chain as it will start r otating upon starting of engine . ■ CHECKING THE OIL SUPPL Y W ARNING • Make sure to set up the bar and the chain when c hec king the oil supply . If not, the r otating parts may be e xposed. It is very dangerous. After star ting the engine, run the chain ...
-
Zenoah G500AVS - page 10
G455A VS / G500A VS GB-10 ■ ST OPPING THE ENGINE 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. Carburetor anti-freeze mechanism Operating chain saws in temperatures of 0 – 5°C at times of high humidity may result in ice forming within the car - buretor , and this ...
-
Zenoah G500AVS - page 11
G455A VS / G500A VS G B GB-11 6. Sawing • Before pr oceeding to y our job, read the section “For Safe Op- eration”. It is recommended to first practice sa wing easy logs. This also helps you get accus- tomed to your unit. •A lwa ys follow the saf ety regu- lations. The chain sa w must only be used f or cutting wood. It is forbid den to cut ...
-
Zenoah G500AVS - page 12
G455A VS / G500A VS GB-12 W ARNING • Before c leaning, the inspecting or repairing the unit, make sure that engine has stopped and is cool. Dis- connect the spark plug to prevent accidental starting. ■ MAINTENANCE AFTER EA CH USE 1. Air filter Dust on the cleaner surface can be removed by tapping a corner of the cleaner against a hard surface. ...
-
Zenoah G500AVS - page 13
G455A VS / G500A VS G B GB-13 Place the file on the cutter and push straight forward. Keep the file position as illustrated. After each cutter has been filed, check the depth gauge and file it to the proper level as illustrated. 4. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.65 mm as necessary . 5. Sprocket Check for c ...
-
Zenoah G500AVS - page 14
G455A VS / G500A VS GB-14 W ARNING • This saw is equipped with one of the f ollowing lo w kickbac k bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain 14 3644-52112 3611-52210 (21BP) 16 3645-52113 3612-52210 (21BP) 18 3646-52113 3646-52210 (21BP) • The bar rail should always be square. Check for wear of the bar rail. Apply ...
-
Zenoah G500AVS - page 15
G455A VS / G500A VS G B GB-15 10. Specifications Po wer unit: Displacement (cm 3 ): G455A VS ............................................................ 45.0 G500A VS ............................................................ 49.3 Fuel: ................ Mixture (Gasoline 50 : T wo-cycle oil 1) (when using ZENOAH genuine oil) Fuel tank capacity ( ...
¿Tienes una pregunta acerca de Zenoah G500AVS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Zenoah G500AVS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Zenoah G500AVS probablemente compartirá una forma de solucionarlo.