-
Makita 9560CV - page 1
a 9561CV ___ Angle Grinder 2.800 - 10,5001min 289 mm (11 318”) 1 7 kg (3 7 Ibs) 518” 100 mm (4”) MODEL 9560CV 115 mm (4-112”) MODEL 9564CV 100 mm (4”) MODEL 9563CV 125 mm (5”) MODEL 9565CV 115 mm (4-112”) MODEL 9561CV 9565CV I 2,800 ~~ 10,50O/min. I 299 mm (1 1-314”) INSTRUCTION MANUAL 1 8 kg (4.0 Ibs) 518” DOUBLE INSULATION SPECI ...
-
Makita 9560CV - page 2
GENERAL SAFETY RULES USAooz-i (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not ope ...
-
Makita 9560CV - page 3
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. ...
-
Makita 9560CV - page 4
Specific Safety Rules USBOOS-l 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3. Hold tool by insulated gripping surf ...
-
Makita 9560CV - page 5
SYMBOLS The followings show the symbols used for tool. v .................................... volts A .................................... amperes Hz .................................... herts ?., .................................... alternating current b .................................... no load speed H .................................... Clas ...
-
Makita 9560CV - page 6
FUNCTIONAL DESCRIPTION Switch action CAUTION: Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when the side of the switch lever is depressed. To start the tool, slide the switch lever to "I" position. For continuous operation, depress the front of the switch le ...
-
Makita 9560CV - page 7
ASSEMBLY Installing and removing wheel cover Installing Pull the lever in the direction of the arrow after loosening the screw. Install the wheel cover on the bearing box by adjusting the convex of the wheel cover to Turn the wheel cover by 180 degrees. Fasten it with the screw after pulling the lever the For the working purpose, the setting angle ...
-
Makita 9560CV - page 8
Installing or removing the depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and ...
-
Makita 9560CV - page 9
WARN1 NG : It should never be necessary to force the tool. The weight of the tool applied adequate pressure. Forcing and excessive pressure could cause dangerous when wheel breakage. Continued use of a worn-out wheel may result in wheel explosion and serious personal injury. Depressed center wheel should not be used after it has been worn down to 7 ...
-
Makita 9560CV - page 10
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Size 4"xlWx518" 4-1/2" x 5B" ...
-
Makita 9560CV - page 11
@ Rubberpad 743036-3 743015-1 9565CV @ Abrasive discs (For abrasive disc) Part No. Part No I Diameter Per pkg 74203603 For Model 4' 794107-8 794108-8 142072-A-5 742073-A-5 742074-A-5 742075-A-5 742076A-5 742072-8 742073-8 742074-8 742075-0 7420768 742087-0 7420400 7941 05-A-5 80 120 - 24 30 50 5 80 5" 120 24 36 50 1 80 120 - - - - - - - - ...
-
Makita 9560CV - page 12
@ Cut-off wheel Pan No. Size Grit Wheels per pkg. For use 724104-110 4" x 3/32" x 5"' 36 10 For masonry and concrete. 724107-510 4" x 5/64" x 5B" 46 10 For steel and cast iron. For Model 9560cv 9563CV Knot-Type Knotted-Twist Wire cup brush 9564CV Wire cup brush Stringer Bead Twist Wire brush wheel Full Cable Twist ...
-
Makita 9560CV - page 13
+ 57 56 55 54 50 48 G 47 @- 46 13 ...
-
Makita 9560CV - page 14
ITEM NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 I6 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PIN CAP COMPRESSION SPRING 8 GEAR HOUSING COMPLETE HEX. NUT M6 FLAT WASHER 6 SPIRAL BEVEL GEAR 11 LOCK SPRING 12 RETAINING RING S-12 BALL BEARING 6001LLB FLAT WASHER 12 GEAR HOUSING COVER FAN 57 ARMATURE ASSY INC. 12.14-16 INSULATION WASHER FLAT ...
-
Makita 9560CV - page 15
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of Califomia] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: 0 Lead from lead-based paints, 0 Crystalline silica from bricks and cement and other masonry products, ...
¿Tienes una pregunta acerca de Makita 9560CV?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 9560CV, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 9560CV probablemente compartirá una forma de solucionarlo.