-
FujiFilm QP242 - page 1
ProLINE-RoadRunner English PN 096-0230-0 02 Operator ’ s Guide for Fuji MFU: QP242, QP351 ,IP 3 ™ CONTENTS Overview Installation Job Setup Operation Maintenance Troubleshooting ...
-
FujiFilm QP242 - page 2
Data I/O has made a conscientiou s effort to ensure that the information in this document is accurate and complete. Data I/O assumes no liability for errors, or for any incidental, consequential, indirect, or spec ial damages, including, without limitation, loss of use, loss or alteration of data, delays, or lost profits or savi ngs, arising from t ...
-
FujiFilm QP242 - page 3
1 ProLINE-Road Runner Opera tor’s Guide A ProLINE-RoadRunner for Fuji........... 2 Jobs and S t atistics........... 3 External V iew ........... 4 Internal Component s........... 5 Control Panel Light s........... 6 Control Panel Bu ttons........... 7 Operator Menus........... 8 Supervisor Menus........... 9 W arnings and Ca utions......... 12 T ...
-
FujiFilm QP242 - page 4
2 ProLINE-Road Runner Opera tor’s Guide A Dat a I/O is proud to introduce a revolutionary new inline solution for high-volume programming of electronic product s. ProLINE-RoadRunner: 1. T ak es programmable devices from a reel... 2. Places them in sockets and programs them with your dat a... 3. Places them on a conveyor belt... 4. Delivers them t ...
-
FujiFilm QP242 - page 5
3 ProLINE-Road Runner Opera tor’s Guide A T askLink™ for Windows ® is required to process devices on ProLINE-RoadRunner . T askLink allows you to create and manage a job dat abase and it analyzes job st atist ics. PCMCIA cards are used to transfer jobs and statistics between T askLink and RoadRunner . For more information on T askLink, see the ...
-
FujiFilm QP242 - page 6
4 ProLINE-Road Runner Opera tor’s Guide A 1. SMT Communications Connection 2. Power and Air Connections 3. Power Switch 4. Handhold for lif ting 5. PCMCIA Card Slot 6. Control Panel 7. Conveyor Belt 8. Mechanical Interface to the Multi-Feeder Unit 9. Electronics Enclosure 10. Robotics Cover External V iew Front Back Cables not shown 4 3 2 7 1 ...
-
FujiFilm QP242 - page 7
5 ProLINE-Road Runner Opera tor’s Guide A 1. Cover T ape T ake-Up Reel 2. T ape-In Module 3. PNP Probes, Precisor , and Cover 4. Reject Bin 5. Socket Adapter , Actuator Plate, and Programmer 3 1 2 4 5 Internal Component s ...
-
FujiFilm QP242 - page 8
6 ProLINE-Road Runner Opera tor’s Guide A Control Panel Light s 1. Blue - Stop Indicator . User intervention is required, or the unit is p aused. (Do not remove PCMCIA card unless blue lamp is li t.) 2. Y ellow - Caution Indicator . Correct a problem or the machine will stop. 3. Green - Run Indicator . Lit: A job is running. Blinking: Programmed ...
-
FujiFilm QP242 - page 9
7 ProLINE-Road Runner Opera tor’s Guide A 1. Star t - s t art or resume the chosen job. 2. Menu - exit to the previous menu, —or show the next message (deleting the current one), —or deselect an item. 3. Up and Down Ar rows - move through menu items. 4. Select - select menu items. 5. Pau se - interrupt the job without cancelling it. Contr ...
-
FujiFilm QP242 - page 10
8 ProLINE-Road Runner Opera tor’s Guide A Operator Menus are visible on the RoadRunner control p anel, and can be navigated by using the Up Ar r ow and Down Ar row buttons. Pressing the Menu button displays the menu that is one level up. If you are at the main menu, pressing Menu will have no effect. Jo b is the first item in the main menu. NOTE: ...
-
FujiFilm QP242 - page 11
9 ProLINE-Road Runner Opera tor’s Guide A View th e Supervisor Menus by inserting a PCMCIA c ard with supervisor authority . (The menus on this p age and the next two pages are in addition to the Operator Menus.) Supervisor (Administrator) authorization is set in T askLink. For more information, refer to the T askLink Help Menu. V ersion 5.14.00 ...
-
FujiFilm QP242 - page 12
10 ProLINE-Road Runner Opera tor’s Guide A Refer to the previous pa ge for the main menu. Note that many of th e values shown, such as the T each and Network menus, are f or example only . • Light gra y shaded fields cannot be changed. Operation Job Pick Retries: 2 Error Retries: 3 Pocket Pitch: 4 Pocket Advance: 3 Head V elocity: 250 Accel: 70 ...
-
FujiFilm QP242 - page 13
11 ProLINE-Road Runner Opera tor’s Guide A Refer to the main Supervisor Menu (2 pages back) for orient ation. NOTE: Programmer Diags are only available with a Diagnostic Adapter Board. 1 Actuation duration is set by the Soc ket Adapter . For more information about menu commands, see Chapter 3 of the ProLINE-RoadRunner Owner ’s Manual. R o b ...
-
FujiFilm QP242 - page 14
12 ProLINE-Road Runner Opera tor’s Guide A W arnings and Cautions Compressed Air Point air hoses away from body . Always wear ap proved eye protectio n. Loud Noise Sound pressure levels may excee d 85db. Hearing prote ction is recommended for prol onged exposure at this level. High Vo l t a g e T urn power off before removing electron ics cover . ...
-
FujiFilm QP242 - page 15
13 ProLINE -RoadRunner Operator’s Guid e A Mounting on the Feeder Bank ...... 14 Connecting Power and Air ...... 16 Running the Self-T est ...... 18 Installation Chapter 2 ...
-
FujiFilm QP242 - page 16
14 ProLINE-Road Runner Opera tor’s Guide A T o mount RoadRunner onto an MFU: 1. Align and push the communica- tions cable into the MFU. NOTE: T o allows access to RoadRunner , do not use the ten right-most slot positions on the MFU. 2. While holding RoadRunner at a slight nose-down angle, let the nose rest on the MFU. Ensure that it settles into ...
-
FujiFilm QP242 - page 17
15 ProLINE -RoadRunner Operator’s Guid e A 3. Stil l holding it at an angle, slide it forward as far as it will go. (The nose will fit under the lip on the MFU.) 4. Lower RoadRunner and jiggle it to ensure that the angle bracket has settled into the spring clamp on the MFU. NOTE: The assembly machine pick point will correspond with the MFU slot n ...
-
FujiFilm QP242 - page 18
16 ProLINE-Road Runner Opera tor’s Guide A T o connect the power and the air: 1. T urn the RoadRunner power switch to the Off (0) position. 2. Grasp the air hose behind the “quick connect” collar and push it firmly onto th e male fitting. The collar must be allowed to move back as it goes onto the fitting. NOTE: Compressed air must be clean a ...
-
FujiFilm QP242 - page 19
17 ProLINE -RoadRunner Operator’s Guid e A 3. Connect to a grounded power source using a cable with a st andard IEC 320 plug. RoadRunner accept s power between 100 and 240 V AC, 50/60Hz. 4. Align and push the communications cable end into the RoadRunner connector . (The other end should already be connected to the MFU.) NOTE: T o disconnect the a ...
-
FujiFilm QP242 - page 20
18 ProLINE-Road Runner Opera tor’s Guide A T o run the Self-T est: 1. T urn the pow er switch On (I). All the control p anel indicator lamps light up. When the Self- T est finishes, the blue lamp will remain on and the version number will display . If all the indicator lamp s st art blinking, a serious error has occurred. T urn the unit off then ...
-
FujiFilm QP242 - page 21
19 ProLINE-Road Runner Opera tor’s Guide A Inserting a Job Card ..... 20 Changing the Precisor ..... 22 Changing the Actuator P late..... 24 Changing the Socket Adapter..... 26 Adjusting the T ape-In Module ..... 28 Loading a Reel of Devices ..... 30 Aligning the T ape Pockets ..... 32 Job Setup Chapter 3 ...
-
FujiFilm QP242 - page 22
20 ProLINE-RoadR unner Operat or’s Guide T o run a job, insert a T askLink job card into the PCMCIA card slot. Use only TYPE I or TYPE II PCMCIA cards. T o inse rt a job card: 1. If the power switch is on, make sure the blue lamp is lit. Inserting a Job Card Electrostatic disc harge may cause damage . Discharge static against co mmon gr ound prio ...
-
FujiFilm QP242 - page 23
21 ProLINE-Road Runner Opera tor’s Guide A 2. Slide the job card into the PCMCIA card slot. NOTE: When fully inserted, the job card extends slightly from the PCMCIA card slot. NOTE: Do not eject the card unless the blue lamp is lit (or the power is off). 3. The Car d Eject button can be pushed to remove the card when the blue lamp is lit. 2 3 ...
-
FujiFilm QP242 - page 24
22 ProLINE-RoadR unner Operat or’s Guide T o change the precisor: 1. Select Jo b , then End , wait for the blue lamp to light and turn the power Off (0). 2. Lif t off the Robotics Cover . 3. St arting at one end, pull the precisor down off the magnet, and then pull the other end off. The PNP Head Cover can be removed for easier access. Changing t ...
-
FujiFilm QP242 - page 25
23 ProLINE-Road Runner Opera tor’s Guide A 4. When inserting the new precisor , make sure that the part number faces up and that the small holes near the precisor edge fit over the dowel pins on the PNP head. There should be no visible gap between the precisor and the head. 4 ...
-
FujiFilm QP242 - page 26
24 ProLINE-RoadR unner Operat or’s Guide T o change the Act uator Plate: 1. Select Jo b , then End , wait for the blue lamp to light and turn the power Off (0). 2. Lif t off the Robotics Cover . Once power is off, the PNP Head can be moved by hand to allow access to the A ctuator Plate. PNP Head Changing the Actuator Plate Warning: Pinch Warnin g ...
-
FujiFilm QP242 - page 27
25 ProLINE-Road Runner Opera tor’s Guide A 3. Pull the Actuator Plate to slide it out of the grooved brackets. NOTE: The Actuator Plate must be out to access or change the Socket Adapter . T o change the Soc ket Adapter , see the procedure on the following pa g e . 3 ...
-
FujiFilm QP242 - page 28
26 ProLINE-RoadR unner Operat or’s Guide T o change the Socket Adapter (with the Actuator Plate removed): 1. Make sure the power is Off (0). 2. Unscrew the two captive scre ws and lift the adapter bracket. 2 2 Changing the Socket Adapter Caution: Electrostatic Disc harge may cause damage. Discharge sta tic agai nst common groun d. ...
-
FujiFilm QP242 - page 29
27 ProLINE-Road Runner Opera tor’s Guide A 3. Without touching the gold cont act surfaces on the bottom of the adapter , lif t the adapter free. 4. Insert the correct adapter , making sure that it seats on the dowel pins. NOTE: Each type of device may have its own Socket Adapter . 5. Tighten the screws and replace the Actuator Plate. 3 ...
-
FujiFilm QP242 - page 30
28 ProLINE-RoadR unner Operat or’s Guide If you have an Adjust able T ape-In Module, you may need to adjust the ta p e w i dt h . Adjust able T ape-In Module only— If the etched number on the 3-Position Sp acer does not match your t ape wid th dimension (mm): 1. With the power off (0), move the PNP Head out of the way . 2. Loosen the Position L ...
-
FujiFilm QP242 - page 31
29 ProLINE-Road Runner Opera tor’s Guide A 3. Rot ate the 3-Position Sp acer with your finger until you read 16, 24 or 32, corresponding to your t ape width. 4. Retighten the Position Locking Screw . 5. Rot ate the Peel Bar counterclockwise 180 degrees to the up position. 6. Lif t and move the magnetic Front T rack to the position that f i ts y o ...
-
FujiFilm QP242 - page 32
30 ProLINE-RoadR unner Operat or’s Guide T o load and thread dev ice t ape: 1. Place a reel onto the RoadRunner spindle. 2. Lock the reel in place by rot ating the brass button on the spindle end. 3. Insert the device t ape into the T ape-In Module and onto the sprocket. 4. Select Advance Poc ket from the operator menu, then press the Up Ar r ow ...
-
FujiFilm QP242 - page 33
31 ProLINE-Road Runner Opera tor’s Guide A 5. When the t ape is advanced p ast the Peel Bar , separate the cover t ape from the device t ape. 6. Thread the cover t ape up through the cover tape p ath and att ach it to the Cover T ape T ak e-Up Reel. Advance the tape as necessary . NOTE: A small piece of adhesive tape may be needed to stick the co ...
-
FujiFilm QP242 - page 34
32 ProLINE-RoadR unner Operat or’s Guide T o align the tape pocket s: 1. Select Align P ock et from the Operator Menu. 2. Press the Up Ar r ow button to advance the t ape until the next t ape pocket center hole is approximately centered at the pick point alignment mark. Do not advance devices p ast the pick point. They may fall and jam the t ape ...
-
FujiFilm QP242 - page 35
33 ProLINE-Road Runner Opera tor’s Guide A Running a Job ........ . 34 Pausing or S topping a Job ......... 35 Ending a Job ......... 36 Emptying the Reject Bin ........ . 38 Emptying Cover T ape ......... 39 Shutting Down .. ....... 40 Rest arting a Job ......... 42 Operation Chapter 4 ...
-
FujiFilm QP242 - page 36
34 ProLINE-Road Runner Opera tor’s Guide A T o run a job: 1. Insert a job card into the PCMCIA card slot. 2. Clear the conveyor belt of any unneeded devices. 3. Press Start . The green lamp will st art blinking. When the programmed devices reach the assembly machine pick point, the belt will p a use and the green lamp will st ay lit without blink ...
-
FujiFilm QP242 - page 37
35 ProLINE-Road Runner Opera tor’s Guide A T o pause at the end of the current operation: 1. Press Pause on the control pa n e l . T o instantly stop in an emergency situation: 2. Press the Emer gency Stop (E-Stop) button. The E-Stop does not stop the assembly machine. Pausing or Stopping a Job 1 > Job Advance Po cket Align Pocket 2 > J ...
-
FujiFilm QP242 - page 38
36 ProLINE-Road Runner Opera tor’s Guide A Whenever you are going to change job cards, you must first end the current job. T o end the current job: 1. Press Pause button. 2. Select End from the Job Menu. Job is in the main menu. The system will finish processing devices and place the devices on the belt, but no additional devices will get picked ...
-
FujiFilm QP242 - page 39
37 ProLINE-Road Runner Opera tor’s Guide A 3. Clear away excess devic es from the conveyor belt. 4. Empty the Reject B in. (See next heading.) 5. Empty the Cover T ape T ake-Up Reel. (See “Emptying Cover T ape” ahead several pages.) 3 4 5 ...
-
FujiFilm QP242 - page 40
38 ProLINE-Road Runner Opera tor’s Guide A T o empt y the Reject Bin: 1. Press the Pause button. 2. Pull the Reject Bin out by grabbing the finger t ab and then lif t up and out. When reinserting the R eject Bin, be sure the bin is comp letely lowered so that the t ab is positioned out of the path of the probes. Emptying the Reject Bin 2 Warn ...
-
FujiFilm QP242 - page 41
39 ProLINE-Road Runner Opera tor’s Guide A T o empt y the Cover T ape T ake-U p Reel: 1. Press Pause . 2. Cut the cover tape, leaving enough slack to reatt ach. 3. Pull the T ake- Up Reel straight out. (Reels with slot s require rot ating before pulling off.) 4. Unwind the used cover tape and discard it. 5. Replace the T ake-Up Reel—slide it on ...
-
FujiFilm QP242 - page 42
40 ProLINE-Road Runner Opera tor’s Guide A T o shut down RoadRunner: 1. Press Pause . 2. Select End J ob from the Job Menu and wait for all devices to be placed on the belt. 3. T urn the pow er Off (0). 4. Remove devices from the conveyor belt. Shutting Down 1 >J o b Advance Pocket Align Pocket Purge 3 Reel not shown ...
-
FujiFilm QP242 - page 43
41 ProLINE-Road Runner Opera tor’s Guide A 5. Empty the Reject B in. 6. Remove and empty the T ake-Up Reel. (For more, see the previous heading.) 7. Remove the air hose or shut off the air flow . NOTE: When disconnecting the air hose, pull the connector collar back as you pull the connector off. 5 6 ...
-
FujiFilm QP242 - page 44
42 ProLINE-Road Runner Opera tor’s Guide A T o restart RoadRunner af ter a pause or an emergency stop: 1. T urn the Emer gency Stop button clockwise to release it, if needed. 2. Press Menu until the main level menu is displayed 3. Select Align P ock et. 4. Press the Up Ar row to advance the device t ape until the next pocket center hole lines up ...
-
FujiFilm QP242 - page 45
43 ProLINE-Road Runner Opera tor’s Guide A Cleaning with Air ......... . 44 Cleaning with Alcohol.......... 45 Running the Self-T est.......... 46 Maintenance Chapter 5 ...
-
FujiFilm QP242 - page 46
44 ProLINE-Road Runner Opera tor’s Guide A T o prevent dust accumulat ion, inject compressed air into the following component areas: 1. T ape-In Module (weekly). 2. Socket s (daily). Socket s should be opened and closed by hand while air is injected. NOTE: Compressed air must be clean and dry . Cleaning with Air 1 2 Warning: Point Air Hoses A ...
-
FujiFilm QP242 - page 47
45 ProLINE-Road Runner Opera tor’s Guide A T o prevent dust and oil accumulations, clean the following component areas with isopropyl alcohol on a lint-free cloth. • Chassis and Covers (every 3 months). • Conveyor belt (daily). See "Device Rot a tion" in the T roubleshooting chapter . NOTE: Dry the conveyor belt before rotating it. ...
-
FujiFilm QP242 - page 48
46 ProLINE-Road Runner Opera tor’s Guide A Run the Self-T est procedure approximately once a week. T o run the Self-T est procedure: 1. Press Pause . 2. Clear all devices from the socket s and from the conveyor belt. 3. T oggle the power switch off and then back on. The Self-T est will run, checking the condition of the component s. 4. Check the ...
-
FujiFilm QP242 - page 49
47 ProLINE-Road Runner Opera tor’s Guide A Viewing Errors.. .......... 48 Enabling a Socket........... . 50 Clearing Jammed T ape............ 51 Device Rot ation............ 52 T echnical Support............ 53 T roubleshooting Chapter 6 ...
-
FujiFilm QP242 - page 50
48 ProLINE-Road Runner Opera tor’s Guide A Viewing Errors T o vie w and correct errors: 1. Messages will appear in the keypad display . 2. Check the condition—t ape p ath, Reject Bin, etc.—implied by the message. If you cannot correct the error condition, cont act a service technician . 3. Press Menu to remove the message. If there are other ...
-
FujiFilm QP242 - page 51
49 ProLINE-Road Runner Opera tor’s Guide A Sto p Caution Motor Cont roller not responding Some common error messages are listed below . For more information see “T roubleshooting” in the ProLINE-RoadRunner Owner ’s Manual . 1 Twist the Emer gency Stop bu tton to rel ease it. Lamp Color Error Message No change in lamps Card not present Y ...
-
FujiFilm QP242 - page 52
50 ProLINE-Road Runner Opera tor’s Guide A If a socket r epeatedly becomes disabled, RoadRunner should be serviced. T o re-ena ble a disabled socket: 1. Select Sock et from the top level menu. 2. Arrow down and select the disabled socket from the Socket menu. (A dot appears.) 3. Press the Up Ar r ow button to re-enable the socket. NOTE: T o disab ...
-
FujiFilm QP242 - page 53
51 ProLINE-Road Runner Opera tor’s Guide A If the t ape jams, an error message displays and the blue lamp illuminates. T o clear the tape p ath: 1. Press the Emer gency Stop button (to continue the job later) or select Job , then End . T urn the power off. 2. Unroll one turn of cover t ape and cut it near the T ake -Up Ree l. 3. Cut the de vi ce ...
-
FujiFilm QP242 - page 54
52 ProLINE-Road Runner Opera tor’s Guide A Device Rot ation If devices rotate excessively on the conveyor belt: 1. Press Pause . W ait for all t he devices to get picked from the belt. 2. Press the Emer gency Stop . 3. Remove the D ust Cover and clean only the exposed surface of the conveyor belt with isopropyl alcohol on a lint-free cloth, then ...
-
FujiFilm QP242 - page 55
53 ProLINE-Road Runner Opera tor’s Guide A Wo rldwide Data I/O Corporation Shippin g address: 10525 Willows Road N.E. Redmond, W A USA 98052 Mailing address: P .O. Box 97046 Redmond, W A USA 98073-9746 T ele pho ne: 425-867-6870 USA Only: 1-800 -332- 82 46 Fax: 425-882-1043 E-mail: s upport@da taio.com Y ou can also find answers by visiting the K ...
¿Tienes una pregunta acerca de FujiFilm QP242?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con FujiFilm QP242, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con FujiFilm QP242 probablemente compartirá una forma de solucionarlo.