-
Hearth and Home Technologies 6000BE - page 1
1 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Underwriters Laboratories Listed Models: 6000BE 6000BE-IPI In the Commonwealth of Massachusetts: • installation must be performed by a licensed plumber or gas fitter; • a CO detector shall be installed in the room where the appliance is installed. Î - Do n ...
-
Hearth and Home Technologies 6000BE - page 2
2 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or component s MA Y BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEV ...
-
Hearth and Home Technologies 6000BE - page 3
3 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 TABLE OF CONTENTS Safety and W arning Information ................................................ 2 Service Parts Lists ..................................................................... 4 Section 1: Approvals and Codes ..................................... ...
-
Hearth and Home Technologies 6000BE - page 4
4 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Part number list on following page. 5 12 6 Log Set Assembly 2 1 3 11 7 (NG , LP) Exploded Parts Diagram Service Parts 6000BE, 6000BE-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ 4 10 9 8 ...
-
Hearth and Home Technologies 6000BE - page 5
5 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 IT E M CO M MO N P A RTS SERI A L # P A RT NUM BER 1 S ur r o un d 2026- 1 08 2 Hood SRV60- 143- BK 3 G la s s D o o r A s s e m b ly GLA- 750T R 4B u r n e r N G 381-376A 4B u r n e r L P 381-375A 5 Log Gr at e 060- 361 A 6 Log Set A ssembl y ( On l y sol d as ...
-
Hearth and Home Technologies 6000BE - page 6
6 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 (NG , LP) Exploded Parts Diagram Service Parts 6000BE-IPI IT EM DESCR I PTI O N SERI A L # P A RT NU MBER 1 V al v e Bracket 2025-101 2 F le x B a ll Va lve A s s e mb ly 302-320A 3P i l o t A s s e m b l y N G 4021-025 3 Pi lot A ssem bly LP 4021-026 4 ON / OF ...
-
Hearth and Home Technologies 6000BE - page 7
7 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 (NG , LP) Exploded Parts Diagram Service Parts 6000BE IT E M DES CRI PT I O N SERI A L # P A RT NUMBER 1 B u rn er O rifice (N G) (#38C 582-838 1 B ur ne r O r i f i c e ( L P ) ( # 5 2 C ) 582-852 2V a l v e N G 060- 522 2 V alv e LP 060-523 3 Fl ex i ble G as ...
-
Hearth and Home Technologies 6000BE - page 8
8 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Appliance Certification The Hearth & Home T echnologies fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. Certification MODELS: 6000BE, 6000BE-IPI LABORA TOR Y : Underw ...
-
Hearth and Home Technologies 6000BE - page 9
9 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 2 Getting St arted Introducing the Hearth & Home T echnologies Gas Fireplaces Hearth & Home T echnologies direct vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to ...
-
Hearth and Home Technologies 6000BE - page 10
10 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 1. Diagram of the 6000BE, 6000BE-IPI 41 [1040mm ] 38 [965mm] 36 1/ 8 [916mm ] 25 1/ 4 [642mm ] 34 5/8 [879mm] 8 [203mm] VENT COLLARS ELECTRICAL ACCESS 26 7/8 [682mm] 12 3/4 [323mm] 3 1/2 [90mm] GAS LINE ACCESS 2 1/8 [55mm] 6 7/8 [174mm ] 14 1/4 [362m m] ...
-
Hearth and Home Technologies 6000BE - page 11
11 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 3 Inst alling the Fireplace Step 1. Locating the Fireplace The following diagram shows space and clearance require- ments for locating a fireplace within a room. AB C D E 42” 22” 36” 51” 72” Note* 42” 22” 40” 57” 80” Minimum Clearances from ...
-
Hearth and Home Technologies 6000BE - page 12
12 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 A . ............. 42”* B . ......... 38 1/2” C . ............... 2 2 ” D . ......... 42 3/4” E . ......... 27 7/8” Figure 3. Framing Dimensions Step 2. Framing the Fireplace Fireplace framing can be built before or after the fireplace is set in place ...
-
Hearth and Home Technologies 6000BE - page 13
13 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 4. DVP-Series Direct V ent Component Specifications (5-inch inner pipe / 8-inch outer pipe) NOTE: PIPES OVERLAP 1-1/4 INCHES A T EACH JOINT . D V P 9 0 S T 12-9/16 11- 1/ 4 7-1/4 1-1/4 TYP 1/2 TYP 8-9/16 DVP36 DVP48 48 24 36 4 6 DVP4 DVP6 12 DVP12 2 MIN ...
-
Hearth and Home Technologies 6000BE - page 14
14 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 5. V ent System Components and T ermination Kits Step 3. Inst alling the V ent System A. V ent System Approvals These models are approved to use DVP-series direct vent pipe components and terminations (see Figures 4 and 5). Approved vent system componen ...
-
Hearth and Home Technologies 6000BE - page 15
15 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 6. Straight Up V ertical V enting STRAIGHT UP VERTICAL VENTING V (FT .) 40' MAX. (12.4 M) CAP V Flue Restrictor Instructions 1. Remove Exhaust Shield using a 1/4” nut driver by removing the four screws securing it in place (see Figure 7). Figure ...
-
Hearth and Home Technologies 6000BE - page 16
16 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 HORIZONT AL VENTING Kit No. H Max. Run DV P-T RA P 24" (610 mm) Figure 1 1. Corner Inst allation NOTE: This model is tested and approved to use 45° elbows in corner installations. Howev- er , 90° elbows will result in better performance. The use of two ...
-
Hearth and Home Technologies 6000BE - page 17
17 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 V H 1' MIN. (305mm) 2' MAX. (610mm) 2' MIN. (610mm) 4' MAX. (1.22m) 3' MIN. (914mm) 6' MAX. (1.86m) 4' MIN. (1.22m) 8' MAX. (2.4m) V+H=40' MAX. (12.4m) H = 8' MAX. (2.4m) NOTE: On vertical venting configuration ...
-
Hearth and Home Technologies 6000BE - page 18
18 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 14. V enting with T wo 90° Elbows VENTING WITH TWO (2) 90° ELBOWS V H H + H 1 1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52m) 2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1m) 3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.65m) 4´ MIN. (1.2 ...
-
Hearth and Home Technologies 6000BE - page 19
19 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 16. V enting with three 90° elbows VENTING WITH THREE (3) 90° ELBOWS 1´MIN. (305mm) 2´MAX. (610mm) 5´MAX. (1.52m) 2´MIN. (610mm) 4´MAX. (1.22m) 10´MAX. (3.1m) 3´MIN. (914mm) 6´MAX. (1.86m) 15´MAX. (4.65m) 4´MIN. (1.22m) 8´MAX. (2.48m) 20´M ...
-
Hearth and Home Technologies 6000BE - page 20
20 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 VENTING WITH THREE (3) 90° ELBOWS V (FT .) H (FT .) 1' MIN. (305mm) 5' MAX. (1.52m) 2' MIN. (610mm) 10' MAX. (3.1m) 3' MIN. (914mm) 15' MAX. (4.65m) 4' MIN. (1.22m) 20' MAX. (6.2m) NOTE: H + H 1 = 20' MAX. (6.2m) V ...
-
Hearth and Home Technologies 6000BE - page 21
21 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 ! B. Inst alling V ent Components After determining which set of starting collars will be used (top or rear), follow venting instructions accordingly . V enting Out the Rear V ent Remove the installed rear seal cap from the rear starting collars by cutting the ...
-
Hearth and Home Technologies 6000BE - page 22
22 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 3. Continue Adding V ent Component s W ARNING: INST ALLA TION OF THIS FIREPLACE REQUIRES THE USE OF HEA T SHIELD 570-290 ABOVE THE FIRST 90 0 ELBOW IN THE VENTING SYSTEM. Figure 20 T o Install the Heat Shield: 1. Determine if the heat shield is required. Do so ...
-
Hearth and Home Technologies 6000BE - page 23
23 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 5. Install Firestops For Horizontal Runs - Firestops are REQUIRED on both sides of a combustible wall through which the vent passes. NOTE: Model DVP-TRAP does not need an exterior firestop on an exterior combustible wall. T o install firestop s for horizontal ...
-
Hearth and Home Technologies 6000BE - page 24
24 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 26. Ceiling Firestop (Ceiling Side) If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole. NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm). Figure 27. Attic Firestop JOIST C ...
-
Hearth and Home Technologies 6000BE - page 25
25 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 29. Minimum Clearances for T ermination A = 12 inches .................. clearances above grade, veran- da, porch, deck or balcony B = 12 inches .................. clearances ...
-
Hearth and Home Technologies 6000BE - page 26
26 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. ...
-
Hearth and Home Technologies 6000BE - page 27
27 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Step 5. Installing the Optional Heat-Zone Kit NOTE: There must be NO INSULA TION or other com- bustibles inside the framed firestop opening. HEA T-ZONE AT TAC H E S HERE Figure 32. 1. Remove the knockout from the fireplace and discard it (see Figure 32). 2. Ce ...
-
Hearth and Home Technologies 6000BE - page 28
28 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Figure 34. Gas Supply Line • At the gas line access hole, use insulation to re-pack the space around the gas pipe. • Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing. ...
-
Hearth and Home Technologies 6000BE - page 29
29 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Step 9. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENT AL FIREPLACE OPERA TION. For Standing Pilot Ignition Wirin ...
-
Hearth and Home Technologies 6000BE - page 30
30 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Intermittent Pilot Ignition (IPI) Wiring 3 V olt T ransformer This appliance comes with a 3 volt transformer . The trans- former plugs into the junction box and the two leads plug into the green control module (see Figure 37). Appliance Requirements This appli ...
-
Hearth and Home Technologies 6000BE - page 31
31 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Step 10. Finishing Figure 38 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 2 and 3 for other fireplace clearances. Only no ...
-
Hearth and Home Technologies 6000BE - page 32
32 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 ! Follow these steps: 1. Release four glass clips and set the glass assembly aside. CAUTION: The log assembly is fragile. Handle with care. NOTE: See S tep 9 when replacing the log set in an existing fireplace. 2. Carefully cut the cable tie holding the log as ...
-
Hearth and Home Technologies 6000BE - page 33
33 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 ! ! Figure 44 Figure 43 5. The grate is located in the lower cav- ity . Remove the screw holding the grate in place and discard the screw . 6. Position the grate into the cutout in the refractory . Hook the grate into po- sition using the tabs on the bottom of ...
-
Hearth and Home Technologies 6000BE - page 34
34 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Placing the Ember Material Ember material is shipped with this gas fireplace. T o place the ember material: • Pull the four glass latches out of the groove on the glass frame. Remove glass door from the unit (see Figure 45). Figure 46. Placement of the Ember ...
-
Hearth and Home Technologies 6000BE - page 35
35 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 Step 12. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: Remove all paperwork from underneath the fireplace. Review safety warnings and cautions • Read the Safety and Warning Information section at the beginning of t ...
-
Hearth and Home Technologies 6000BE - page 36
36 Hearth & Home T echnologies • 6000BE, 6000BE-IPI • 2024-900 Rev . G • 1 1/05 4 Maint aining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fireplace servicing and main- tenance will depend on use and the type of installation, you should have a qualified service technician perform an appli- ance check ...
¿Tienes una pregunta acerca de Hearth and Home Technologies 6000BE?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hearth and Home Technologies 6000BE, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hearth and Home Technologies 6000BE probablemente compartirá una forma de solucionarlo.