-
Klipsch 5M0198 - page 1
8900 Keystone Crossing, Suite 1220 Indianapolis, Indiana 46240 1 . 800 . KLIPSCH • www.klipsch.com Make sure you return your warranty card so that we may keep you up-to-date on new Klipsch products and promo - tions. As always, if you have any questions, contact your local authorized Klipsch dealer . For your records: Model Serial Number Date Pur ...
-
Klipsch 5M0198 - page 2
K l i p s c h S y n e r g y S e r i e s ™ O w n e r ’ s M a n u a l & W a rr a n t y K S W 5 0 ™ K S W 1 0 0 ™ K S W 1 5 0 ™ K S W 2 0 0 ™ KSW 300 ™ ...
-
Klipsch 5M0198 - page 3
...
-
Klipsch 5M0198 - page 4
1 W e Want Y our Klipsch Product to Look and Sound as Good as When it Left the Factor y . Please Check Promptly for Transit Damage. Each Klipsch product is individually tested for sonic quality and inspected for superior appearance before it leaves the Hope, Arkansas factor y . Your loudspeaker left the factory in perfect condition in packaging car ...
-
Klipsch 5M0198 - page 5
2 Planning Y our Klipsch Home Entertainment System Y our new Klipsch subwoofer will enhance the performance of your home entertainment system, whether used within a two-channel audio or multi-channel home theater system. Speaker placement is important in optimizing the performance of your system. Please refer to the diagrams below as a general guid ...
-
Klipsch 5M0198 - page 6
11 Klipsch Limited Warranty KLIPSCH, L.L.C. (“KLIPSCH”) warrants this product to be free from defects in materials and work- manship (subject to the terms set forth below). For a period of five (5) years from the date of purchase, KLIPSCH will repair or replace (at KLIPSCH’s option) this product or any defective parts (excluding electronics ...
-
Klipsch 5M0198 - page 7
For parallel connection of subwoofer and main speaker wires (main speakers full range), connect the subwoofer wires to the secondary set of speaker terminals (speaker B) if your amplifier is so equipped. If you use your speaker B terminals, they must be internally wired in parallel with the speaker A terminals or you’ll notice a dramatic drop in ...
-
Klipsch 5M0198 - page 8
9 Figur e C Figur e D KSW 300 INPUT PANEL • Main Speakers, Limited Range / Line Level Connections • One Channel Shown / Repeat for Opposite Channel • Optional LFE Connection Shown • Separate Pre-amp and Power Amp Shown / Integrated Components Require Pre-amp Outputs and Main Amp Inputs KSW 100, 150, 200 INPUT PANEL • Main Speakers, Full R ...
-
Klipsch 5M0198 - page 9
6 HIGH PASS This switch selects either “40 Hz” or “80 Hz” as the high pass filter frequency for your main speak - ers when your system is connected as per figure C (page 9). This diagram shows a separate pre-amp and power amp, but also applies to integrated components (such as receivers) possessing pre-amp output and power amp input jacks ...
-
Klipsch 5M0198 - page 10
7 • All KSW powered subwoofer amplifiers are protected by a thermal sensor. If they run for extended periods beyond their designated power rating, the thermal sensor will engage and shut down the subwoofer. If this occurs, turn the “POWER” switch off, reduce the volume level on your elec- tronics and wait five minutes before restarting the ...
-
Klipsch 5M0198 - page 11
8 Figur e A Figur e B KSW 50 INPUT PANEL • Main Speakers, Full Range / Hi Level Connections • One Channel Shown / Repeat for Other Channel KSW 100, 150, 200 INPUT PANEL • Main Speakers, Limited Range / Hi Level Connections • One Channel Shown / Repeat for Opposite Channel • Optional LFE Connection Shown • Integrated Receiver Shown / Wit ...
-
Klipsch 5M0198 - page 12
5 A combination of “HI LEVEL” and “LFE IN”/“SUB” inputs may be used. For example, if you connect your KSW subwoofer to electronics possessing an LFE output, you could use a speaker cable to connect to the “HI LEVEL IN” speaker wire terminals and a shielded interconnect cable to connect to the “LFE IN”/“SUB” input. Refer to F ...
-
Klipsch 5M0198 - page 13
10 KSW 300 T ype: 15" bass reflex, tuned port enclosur e Amplifier: 300 watts continuous into 4 ohms Auto Power On: 2 second ON delay, 15 minute OFF delay Frequency Response: 25-120 Hz±3 dB Maximum Output: 112 dB Audio/Video Switch: +3 dB over entire frequency range Low Pass Crossover: Continuously variable from 40-120 Hz, 24 dB/octave slop ...
-
Klipsch 5M0198 - page 14
3 How to Connect Your KSW Series Subwoofer The subwoofer should be unplugged from the AC power with the power switch in the OFF position during hook up and installation. AC Power A detachable AC power cord is supplied with your KSW Series subwoofer. Install the female end into the recessed socket on the right-hand side of the amplifier panel. Refe ...
-
Klipsch 5M0198 - page 15
SAFETY WARNINGS • Do not make connections (other than the power cord of a powered subwoofer) directly to any AC electrical wall outlet. Connection should be made only to an audio amplifier or equivalent component and only as described in the “Subwoofer Installation” section. • Do not operate the subwoofer under extremely humid or adverse t ...
-
Klipsch 5M0198 - page 16
For multiple speaker purchases, please fill out only one warranty card. Name Address City/State/Zip Age Marital Status ❑ Single ❑ Married ❑ Divorced Highest Education Level ❑ High School ❑ College ❑ Graduate School Did you purchase these speakers for ❑ Music ❑ Home Theater ❑ Both What kind of music do you like? ❑ Rock ❑ Class ...
¿Tienes una pregunta acerca de Klipsch 5M0198?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Klipsch 5M0198, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Klipsch 5M0198 probablemente compartirá una forma de solucionarlo.