-
NEC LCD1970NX - page 1
MultiSync LCD1970VX MultiSync LCD1970NX MultiSync LCD1970NXp User’ s Manual ...
-
NEC LCD1970NX - page 2
Index W arning, Caution ............................................................................................................... .......... English-1 Declaration ................................................................................................................................... English-1 Canadian Depar tment of Communications ...
-
NEC LCD1970NX - page 3
English English-1 W ARNING CA UTION CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGA GE THE POWER T O THE UNIT , PLEASE DISCONNECT THE PO WER CORD FROM THE A C OUTLET .DO NO T REMO VE CO VER (OR BA CK). NO USER SER VICEABLE P ARTS INSIDE. REFER SER VICING T O QUALIFIED SER VIC ...
-
NEC LCD1970NX - page 4
English-2 Canadian Depar tment of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations . C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1 . Use the attached spe ...
-
NEC LCD1970NX - page 5
English English-3 Contents Y our new NEC MultiSync LCD monitor box* should contain the f ollowing: • MultiSync LCD monitor with tilt/swiv el/height adjust stand • P ower Cord • Cable co ver • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) • User ’ s Manual • CD ROM (includes complete User ’ s Manual in PDF f o ...
-
NEC LCD1970NX - page 6
English-4 Quic k Star t T o attach the MultiSync LCD monitor to your system, f ollow these instructions: 1. T ur n off the power to your computer . 2. For the PC or MA C with D VI digital output: Connect the D VI signal cable (not included) to the connector of the displa y card in your system ( Figure A.1 ). Tighten all scre ws. For the PC with Ana ...
-
NEC LCD1970NX - page 7
English English-5 Inser t T op First Then Bottom 7. Place the D VI cab le into the specific hooks indicated in Figure C.3 . 8. Make sure all cab les are resting flat against the stand ( Figure C.3 ). Figure D .1 Figure D .2 D VI Cable Flat Figure C.3 9. Hold the all cables firmly and place the cable co ver onto the stand ( Figure D.1 ). T o remov e ...
-
NEC LCD1970NX - page 8
English-6 Figure S.1 Figure RL.1 Raise and Lower Monitor Screen The monitor may be r aised or lowered. T o raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height ( Figure RL.1 ). NO TE: Handle with care when raising or lowering the monitor screen. Tilt and Swivel Grasp both sides of the monitor screen ...
-
NEC LCD1970NX - page 9
English English-7 Figure S.3 Figure S.4 5. Lift up the stand to unlatch the upper hooks and remov e the stand ( Figure S.3 ). 6. Remov e the 2 screws on the top of the monitor ( Figure S.4 ). The monitor is now ready for mounting in an alternate manner . 7. Connect the cables to the bac k of the monitor . 8. Rev erse this process to re-attach stand ...
-
NEC LCD1970NX - page 10
English-8 Contr ols OSM (On-Screen Manager) control b uttons on the fr ont of the monitor function as follo ws: T o access OSM menu, press any of the control b uttons (MENU/EXIT , Left, Right, Down, Up). T o change signal input, press the SELECT button. T o change D V MODE, press the RESET button. NO TE: OSM must be closed in order to change signal ...
-
NEC LCD1970NX - page 11
English English-9 Colour Contr ol System Colour Control System: Six colour presets select the desired colour setting (sRGB and NA TIVE colour presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour will appear on screen and the direction (increase or ...
-
NEC LCD1970NX - page 12
English-10 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLO WING WHEN SETTING UP AND USING THE MUL TISYNC LCD COLOUR MONIT OR: • DO NO T OPEN THE MONITOR. There are no user serviceable par ts inside and opening or removing cov ers may e xpose you to dangerous shoc k hazards or other risks. Ref er a ...
-
NEC LCD1970NX - page 13
English English-11 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLO WING WHEN Y OU POSITION THE MONIT OR: • F or optimum performance, allow 20 min utes for w ar m-up. • Adjust the monitor height so that the top of the screen is at or slightly below ey e le vel. Y our eyes should look s ...
-
NEC LCD1970NX - page 14
English-12 Specifications f or LCD1970VX Monitor Specifications MultiSync LCD1970VX Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) Viewab le Image Size: 48.2 cm/19.0 inches liquid crystal display (LCD); 0.294 mm dot Native Resolution (Pix el Count): 1280 x 1024 pitch; 250 cd/m 2 white luminance; 550 ...
-
NEC LCD1970NX - page 15
English English-13 Specifications f or LCD1970NX Monitor Specifications MultiSync LCD1970NX Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) View able Image Size: 48.2 cm/19.0 inches liquid crystal display (LCD); 0.294 mm dot Native Resolution (Pix el Count): 1280 x 1024 pitch; 250 cd/m 2 * 3 white lu ...
-
NEC LCD1970NX - page 16
English-14 Specifications f or LCD1970NXp Monitor Specifications MultiSync LCD1970NXp Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) Viewab le Image Size: 48.2 cm/19.0 inches liquid crystal display (LCD); 0.294 mm dot Native Resolution (Pix el Count): 1280 x 1024 pitch; 250 cd/m 2 white luminance; 8 ...
-
NEC LCD1970NX - page 17
English English-15 Features Thin-frame design creates more desktop space for y ou to work and play , while the flat screen ’ s crisp, bright images and cr ystal- clear text deliv er a comf or table viewing e xperience. No T ouch Auto Adjust automatically adjusts y our optimal image settings upon initial power-on. Colour Control System allows y ou ...
-
NEC LCD1970NX - page 18
English-16 T r oub leshooting No picture • The signal cab le should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position. • F ront P ower Switch and computer po wer s witch should be in the ON position. • Check to mak e ...
-
NEC LCD1970NX - page 19
English English-17 TCO’03 Congratulations! The displa y you ha ve just purchased carries the TCO ’ 03 Displa ys label. This means that your displa y is designed, manuf actured and tested according to some of the strictest quality and environmental requirements in the world. This makes f or a high perf or mance product, designed with the user in ...
-
NEC LCD1970NX - page 20
English-18 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the compan y ’ s top prior ities in tr ying to minimize the burden placed on the en vironment. W e are engaged in dev eloping environmentally- friendly products, and alwa ys strive to help define and comply with the latest independent ...
¿Tienes una pregunta acerca de NEC LCD1970NX?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con NEC LCD1970NX, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con NEC LCD1970NX probablemente compartirá una forma de solucionarlo.