-
Cavalry Storage CADT-SA2 - page 1
User's Manual CADT -SA2 Series ...
-
Cavalry Storage CADT-SA2 - page 2
Preface Copyright Please respect copyrighted content. Duplication or modification of this publication in whole or in part is prohibited without written authorization. Usage Strong impacts or dropping the product may cause damage. Allow only qualified personnel to repair this product. Disassembling or opening this product will void your warranty . D ...
-
Cavalry Storage CADT-SA2 - page 3
Thank you for choosing Cavalry . We at Cavalry extend our sincere gratitude for your purchase of this product. We hope our dedication to delivering high quality products with excellent customer service will ensure your continued interest in our products. This manual will assist in the operation of the product. T o optimize your experience with this ...
-
Cavalry Storage CADT-SA2 - page 4
4 4 T able o f Contents Preface ........................................... .......................... ....... ... .. ... ................ 2 List of Accessories ............................................................................. 5 Product Illustrations ........................................................................... 6 Features ...
-
Cavalry Storage CADT-SA2 - page 5
List of Accessories 1. External power adapter / power cord (may vary with product) 2. SA T A to eSA T A adapter cable with bracket 3. eSA T A cable 4. USB 2.0 cable 5. Resources CD 5 5 3 1 2 4 5 ...
-
Cavalry Storage CADT-SA2 - page 6
Front 1 1. LED status indicators 6 6 ...
-
Cavalry Storage CADT-SA2 - page 7
Back 4 7 5 6 2. V entilation fan 3. 0-7 Settings Dial 4. Power switch 5. Power jack 6. eSA T A port 7. USB 2.0 port 7 7 2 3 ...
-
Cavalry Storage CADT-SA2 - page 8
8 Features Plug-and-play for Mac OS v9.x and newer USB 2.0 and eSA T A interface Pre-formatted in Mac OS X Extended Supports RAID levels 0, 1 and 0+1 Exceptional heat dissipating ability LED light indicators Nearly silent operation Designed for use with a Mac 8 ...
-
Cavalry Storage CADT-SA2 - page 9
Setup Instructions Follow the steps below to successfully set up your Cavalry External Hard Drive with your computer . Step 1. Start your computer and wait for the Mac OS to load completely . Step 2. Connect the power adapter to the drive. Then plug the power adapter into an electrical outlet. (Fig. 1) Step 3. Connect the square end of the USB cabl ...
-
Cavalry Storage CADT-SA2 - page 10
SA T A Users : If you do not already have an eSA T A interf ace on your computer , first install the bracket when the computer is off. Then use the eSA T A cable to connect the drive to the bracket. T urn on the unit then turn on the computer . (Please note that S A T A is not required to use your product.) Step 4. T urn the power switch on. NOTE: ...
-
Cavalry Storage CADT-SA2 - page 11
Step 5. Installing drivers for the Cavalry External Hard Drive. Mac OS This drive is preformatted to be plug-and-play for Mac OS 9.x and above. No formatting or drivers should be needed. Windows 2000/XP/Vista Requires reformatting to NTFS: go to the "Contents" folder of the Resources CD and follow the "Formatting Instructions" G ...
-
Cavalry Storage CADT-SA2 - page 12
Windows 98/Me 1. Make sure Windows 98/Me is fully updated. Follow the "Formatting Instructions" PDF (in the "Contents" folder of the CD.) 2. Download drivers from www .cavalrystorage.com/su_downloa d.htm Click on "Windows 98 Driver" to download file. Extract the file. 3. Navigate the device manager . 4. Right-click on ...
-
Cavalry Storage CADT-SA2 - page 13
12 13 RAID Y our product can be set up as RAID 1 (mirrored). "Mirrored" means that each of the two drives in your array store the same data, providing protection against the failure of one drive; however , when the drive appears on your computer , it will be recognized as a single hard drive. NOTE: Although the box indicates t wo hard dri ...
-
Cavalry Storage CADT-SA2 - page 14
Change RAID Settings There are two ways to change the product settings. We recommend using the SteelVine software included with your drive; you may also use the "0-7 Settings Dial" (p17). Changing RAID settings erases any data on the drive . NOTE : Mac Users with OS v10.5 and newer proceed to page 17 for manual configuration of your RAID ...
-
Cavalry Storage CADT-SA2 - page 15
Step 3. Follow the on-screen instructions to install the software. Step 4. After installation is completed, open the 57xx SteelVine Manager . Step 5. Once the program has loaded, go to Edit >> Configure Box. When prompted, enter the default password "admin." 14 15 ...
-
Cavalry Storage CADT-SA2 - page 16
17 16 Step 7. Select the setting that you prefer under "Storage Pol icy", then press "Apply ." NOTE: Changing the settings will erase any data on the unit. Step 8. Y our unit will take a few moments to start rebuilding. Once it h as started, it may take several hours rebuild, depending on the setting you choose. Y ou can monitor ...
-
Cavalry Storage CADT-SA2 - page 17
17 II. Using the "0-7 Settings Dial" (For Mac OS 10. 5 users or users who cannot use the SteelVine software) Step 1. Make sure the unit is off. Step 2. Refer to the following and identify the appropriate number of the setting you would like. Cavalry recommends RAID 1 for data protection: 0 SP ANNI NG, drives are concatenated into one larg ...
-
Cavalry Storage CADT-SA2 - page 18
19 18 Step 3. T urn the unit on its side and look into the hole with the numbers "0" to "7" printed around it (Figure 1). Inside the hole you should see a dial (Figure 2). Figure 1. ...
-
Cavalry Storage CADT-SA2 - page 19
19 18 Figure 2. Step 4. Using a small, flathead screwdriver , turn the dial to the appropriate number of the setting you chose from Step 2. Once you have done this, lay the unit upright and set the unit where you would like it to be. Step 5. T urn the unit on. Step 6. Press the "Reset" or "Update" button located on t he back of ...
-
Cavalry Storage CADT-SA2 - page 20
21 20 III. Partitioning and formatting your RAID syste m These instructions are for users running Mac OS X (10.0+) and above. If you have another operating system, please refer to the Formatting Guide, foun d in the "Contents" folder of the Resources CD or online at www .cavalrystorage.com/su_download.htm Step 1. Go to the top menu and se ...
-
Cavalry Storage CADT-SA2 - page 21
21 20 Step 4. Click on “Options” under the graph. A small window will appear . Choose “default” for partition type. Then click “ok” to exit. Step 5. Now on the right of the graph you can choose your format typ e. Select “MAC OS Extended (journaled).” Step 6. Now click on the “partition” button on the lower right. Step 7. Allow s ...
-
Cavalry Storage CADT-SA2 - page 22
22 T roubleshooting LED light indicator does not turn on Make sure the power adapter is securely connected to a working electrical outlet. Secondly , make sure the USB or eSA T A cable (whichever interface you chose to use) is inserted correctly into the hard drive and the computer . T urn on the power switch (Page 7). Computer does not detect hard ...
-
Cavalry Storage CADT-SA2 - page 23
22 Loud noises coming from external hard drive In most cases, loud noises coming from the drive suggest it may either be defective or a part is loose. We apologize for any inconvenience this may cause. Please contact customer service for assistance. "HDD1" or "HDD2" LED lights become red This indicates one of the drives may need ...
-
Cavalry Storage CADT-SA2 - page 24
Cannot use SteelVine (GUI) software Please confirm that your "0-7 Settings Dial" is set to "7." Follow instructions on page 17 to change the dial to 7 if necessary . Drive will not work with my PC Y ou may have to reformat to NTFS by following the " Formatting Guide" found in the Resources CD or at www .cavalrystorage. ...
-
Cavalry Storage CADT-SA2 - page 25
CA1053 062708 W arranty This product comes with a one year warranty from the date of purchase. Please register your product at www .cavalrystorage. com/prodreg.htm to activate the warranty . Please have your Serial Number and Model Number ready . We are not responsible for any loss of data. Please back up your data often to avoid unexpected losses. ...
¿Tienes una pregunta acerca de Cavalry Storage CADT-SA2?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cavalry Storage CADT-SA2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cavalry Storage CADT-SA2 probablemente compartirá una forma de solucionarlo.