-
Makita 900BL - page 1
I- No load speed IRPMl 6,000 Overall length Net weight Spindle thread 518 - 11 UNC 450 mm I1 7-314") 5.5 kg (12.1 Ibs) Sander MODEL 9000BL INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS ~ * Manufacturer reserves the right to change specificattons without notice. Note Specifications may differ from country to country. ...
-
Makita 900BL - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONM ...
-
Makita 900BL - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 900BL - page 4
ADDITIONAL SAFETY RULES FOR SANDER 1. Check the backing pad carefully for cracks, damage or deformity before 2. Hold the tool firmly. 3. Keep hands away from rotating parts. 4. Make sure abrasive disc is not contacting the workpiece before the switch 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Do not touch the workpie ...
-
Makita 900BL - page 5
Installing side grip (auxiliary handle) Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. Installing or removing abrasive disc CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the disc. NOTE : Use sander accessories specifie ...
-
Makita 900BL - page 6
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly a ...
-
Makita 900BL - page 7
IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual. These must be purchased by separate. WARNING: Always use guard assembly or accessory kit, noted below, for type 27 depressed center wheel. Guard assembly Guard accessory kit Part No. 191214-3. . . For 180 mm (7") Part No. 191215-1 . . . For 230 mm (9") Part No. 1 ...
-
Makita 900BL - page 8
Operation I Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the work- piece. In general, keep the edge of the wheel or disc at an angle of about 15" to the work- piece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of t ...
-
Makita 900BL - page 9
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r ...
-
Makita 900BL - page 10
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Part No. 0 Rubber pad 170 mm (6-3/4") Par ...
-
Makita 900BL - page 11
@ (A) Depressed center wheel (1 per pkg) Part No. Grit Size 741 41 3-3 (B) Makita zirconate (5 per pkg) 180 mm x 6mm x 22 mm 17" w 1 id'' v 71n1,1 24 74142 1-4 @ Wire cup brush 230mmx 6mmx22 mm (9" x 114" x 718") 24 0 Flexible grinding wheel (10 per pkg) 24 741 313-7A Part No. I Grit Sire lmm) 180 mm x 6 mm x 22 mm (7& ...
-
Makita 900BL - page 12
Jan.-26-'90 US SANDER Model 9000BL Note: The switch and other part configurations may differ from country to country. 12 ...
-
Makita 900BL - page 13
MODEL 9OOOBL Jan.-26-'90 US MACHINE 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 'i:M $FD DESCRIPTION MACHINE 2 Pan Head Screw M6x16 IWith Washer) 31 1 1 Tool Rest 32 1 4 Pan Head Screw M5x25 IWith Washer) 33 1 1 1 Shaft Lock Pin 6 34 1 1 Compression Spring 7 35 1 1 Gear Housing 36 1 1 Ball Bearing 629LB ...
-
Makita 900BL - page 14
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, frei ...
¿Tienes una pregunta acerca de Makita 900BL?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 900BL, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 900BL probablemente compartirá una forma de solucionarlo.