-
Fujitsu P3PC-3062-02EN - page 1
P3PC-3062-02EN ...
-
Fujitsu P3PC-3062-02EN - page 2
...
-
Fujitsu P3PC-3062-02EN - page 3
i CONTENTS INTRODUCTION .................... ....................................................... ii Regulatory Informatio n .......................... .............................. ii Liability .................................. ............................................... iii Safety Precautions ... ............................. ...
-
Fujitsu P3PC-3062-02EN - page 4
ii INTRODUCTION Thank you for purchasing the fi- 5950 Duplex Color Scanner. This document describes how to use fi-5950 and basic operation methods. Before you start u sing fi-5950 be sure to thoroughly read this manual to ensure correct use. The "fi-5950 Operator’s Gu ide" stored on the Setup DVD-ROM provides useful and detailed informa ...
-
Fujitsu P3PC-3062-02EN - page 5
iii ■ Liability READ ALL OF THIS MANUAL CAREFULL Y BEFORE USING THIS PRODUCT . IF THIS PRODUCT IS NOT USED CORRECTL Y , UNEXPECTED INJUR Y MA Y BE CAUSED TO USERS OR BYST ANDERS. Also, keep this manual in a safe place so that it can be easily referred to during use of this product. While all efforts have been made to ensure the accuracy of all in ...
-
Fujitsu P3PC-3062-02EN - page 6
iv *1:Where there is no distinction between the diff erent versions of the above operatin g system, the general term "W indows" is used. *2:All the descriptions in this manual assume the usage of Adobe Acro bat bundled with this product. However , Adobe Acrobat may be upgraded without n otice. If the descriptions differ from the screens a ...
-
Fujitsu P3PC-3062-02EN - page 7
v Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen ex amples in this manual, operate by following the actual displayed screen while referring to the User 's Manual of the scanner application you a ...
-
Fujitsu P3PC-3062-02EN - page 8
vi Do not install the scanner in the following locations which are subject to high temperature, humidity , le ss ventilati on, or dust. If placed in an area subject to high temperature, the cover may become overheated and de formed, causing the scanner to become hot, resulting in a fire. • A place near heat-radi ating devices such as stoves or el ...
-
Fujitsu P3PC-3062-02EN - page 9
vii When installing the scanner on a table, make sure that the table is flat and level. Place the scanner so that none of its part s e xtend beyond the edge of the table, otherwise it may fall or collapse and cause injurie s. Install the scanner away from strong magnetic fields and other sour ces of electronic noise. Protect the scanner against any ...
-
Fujitsu P3PC-3062-02EN - page 10
1 Chapter1 PREP ARING THE SCANNER 1.1 Checking the Contents of the Scanner Package When you unpack the scanner package, make sure that the package contains all the pa rts on the list included in the package. If any parts are missing or defectiv e, contact your scan- ner dealer or an authorized FUJITSU scanner service provider. Handle the scanner an ...
-
Fujitsu P3PC-3062-02EN - page 11
2 ■ Removable Parts 1.3 Operator Panel The operator panel is locate d on the rig ht side of the scanner. The panel consists of a Function Number Dis- play, buttons and a LED. No. Name Description 1 Document smoother Attached when the stacker posi- tion is set to align the ejected doc- ument by the leading edge, or when scanning documents with dif ...
-
Fujitsu P3PC-3062-02EN - page 12
3 ■ Indications on the Function Number Display The following shows the in dications on the Function Number Display. Use this button to start linked applica- tion. When this button is pressed during scanning operation, the scanning is cancelled (*About the settings, refer to the "fi- 5950 Operator’s Guid e" on the Setup DVD-ROM). Use t ...
-
Fujitsu P3PC-3062-02EN - page 13
4 Chapter2 INST ALLA TION OF THE SCANNER 2.1 Installing the Scanner 1. Place the scanner at its installation site. For details on the scanner's dimensions and required installation space , refer to the fi-5950 Operator’s Guide, chapte r "10. Scanner Specifi- cations". 2. Connect the AC cable to the Power inlet of the scanner and pl ...
-
Fujitsu P3PC-3062-02EN - page 14
5 ■ Connecting the SCSI interface When using the scanner with a SCSI interface, the fol- lowing SCSI cable and SCSI card mu st be purchased. • SCSI cable Use a SCSI cable whose connector on the scan- ner side is the 68-pin hi gh-density shielded-type and whose connector on the PC side fits the con- nector of the SCSI card to use. It is recommen ...
-
Fujitsu P3PC-3062-02EN - page 15
6 3. When using the SCSI cable, set th e SCSI ID using the SCSI ID switch on the back of th e scanner. (Refer to step 3 in "Connecting the SCSI interface" on page 5 .) 4. Press the "I" side of the main power switch to turn on the scanner. 2.3 Installing the Scanner Software ■ Bundled Software The scanner drivers and app licati ...
-
Fujitsu P3PC-3062-02EN - page 16
7 ■ System Requirements The system requirements for fi-5950 are as follows. *1: Scanner Central Admin Agent is not supported. *2: Not supported by Kofax VRS. *3: QuickScan Pro d oes not support t he Windows 64-bit version. *4: ScandAll PRO and Scan to Micros oft SharePoint are not supported. ■ Installing the Bundled Software The following descr ...
-
Fujitsu P3PC-3062-02EN - page 17
8 4. Install the softwa re, following the onscreen instructions. INSTALL (Custom) 1. Perform Steps 1 and 2 in "INSTALL (Recom- mended)" (page. 7) . 2. Click the [INSTALL (Custom)] button. ⇒ The [INSTALL PROD UCTS] screen appears. 3. Click the button of the software to be installed. 4. Install the softwa re, following the onscreen instru ...
-
Fujitsu P3PC-3062-02EN - page 18
9 2.4 Checking Scanner Driver Operation This section explains how to check the operation of the installed scanner driver by using ScandAll PRO. Make sure that the scanner driver is installed properly, following the procedure below. ■ Checking the Operation of the Scanner Driver 1. Load the document on the scanner. For information about how to loa ...
-
Fujitsu P3PC-3062-02EN - page 19
10 9. In the [Scan Settings] dialog box, clear the [Sa ve to file] checkbox. 10. Click [Scanner Settings]. ⇒ A setup dialog box appears for you to configure scanner driver settings. 11. Configure scanner settings such as the resolution and paper size. T WAIN driver /ISIS driver/Kofax VRS scanner drivers : Configure scan settings, an d then click ...
-
Fujitsu P3PC-3062-02EN - page 20
11 • To remove FUJITSU Scanner USB HotFix, select " FUJITSU Scanner USB HotFix ." 5. Clic k the [Change/ Remove] button or the [Remove] button. 6. When you see a confirmation dialog box, click the [OK] button or the [Yes] button. ⇒ Upon clicking the button, uninstallation is started. HINT • For information abo ut how to u ninstall I ...
-
Fujitsu P3PC-3062-02EN - page 21
AP-1 Appendix 1 TROUBLESHOOTING ■ Troubleshooting checklist Symptom Check this item Remedy Scanner does not turn on. Have you pushed the power button on the front of the scanner? Push the power b utton. Have you pushed the main power switch at the back of the scanner? Push the Main power switch of the scanner. Then push the power button. Is the A ...
-
Fujitsu P3PC-3062-02EN - page 22
AP-2 Paper is not fed (pick error occurs frequen tly, or docu- ment stops midway). Do the documents satisfy the "Docu- ment Quality" and the "Multifeed Detec- tion Conditions" in the chapter 7 of the fi-5950 Operator’s Guide? Use the documents that satisfy the "Document Quality" and the "Multifeed Detecti on Con ...
-
Fujitsu P3PC-3062-02EN - page 23
AP-3 ■ Temporary error The following shows the procedure for releasing of each of the temporary errors. • "J0" or "U1" error 1. Remove the document jammed or stopped in the ADF. (Refer to the fi-5950 Operator’s Guide "6.1 Clearing Document Jams" on the Setup DVD- ROM.) 2. Confirm that the documents meet the paper ...
-
Fujitsu P3PC-3062-02EN - page 24
AP-4 Appendix 2 DAIL Y CARE ■ Cleaning Materials *1: For details about the clean ing materials, contact the FUJITSU scanner dealer where you purchased the scanner. *2: Pre-moistened with Cleaner F1, Cleaning Wipes are used instead of mo istened cloths. ■ Cleaning Method The ADF and the Feed rollers must be cleaned with a lint-free cloth moisten ...
-
Fujitsu P3PC-3062-02EN - page 25
AP-5 Appendix 3 REPLACING CONSUMABLES ■ Consumables and Replacement Cycle The followings are the specif ications of consumables and their recommended replacement cycles. To purchase consumables, conta c t the store where you purchased the scanner or an authorized FUJITSU scanner service provider. The replacement cycles above are rough guidelines ...
-
Fujitsu P3PC-3062-02EN - page 26
AP-6 ■ Pick roller ■ Separator roller ■ Brake roller Pick roller Separator roller Pad Cover Brake roller Cover ...
-
Fujitsu P3PC-3062-02EN - page 27
z Copying of the contents of this manual in whole or in part and copying of the scanner applicat ion is prohibited under the copyright la w. z The contents of this manual are subject to change without notice. z PFU LIMITED is not liable whatso ever for any damages resulting from use of this scanner and proc edures described in this manual, profit l ...
¿Tienes una pregunta acerca de Fujitsu P3PC-3062-02EN?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Fujitsu P3PC-3062-02EN, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Fujitsu P3PC-3062-02EN probablemente compartirá una forma de solucionarlo.