-
Sears 200.71233 - page 1
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 50/15/2 Amp Manual ENGINE ST AR TER With Batter y T ester and Air Compressor 225/125 Amp 00-99-000538/0506 O WNER’S MANU AL Model No. 200.71233 CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. ® ...
-
Sears 200.71233 - page 2
1 W arranty .................................................................... 1 Important Safety Instructions ................................. 2 P arts .......................................................................... 3 Wiring Diagram ........................................................ 3 Before Using Y our Batter y Charger ....... ...
-
Sears 200.71233 - page 3
2 Help us help you REMEMBER: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging. • Never allow battery acid to drip o ...
-
Sears 200.71233 - page 4
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Wiring Diagram Replacement Parts List DieHard 71233 ITEM DESCRIPTION PART NUMBER 1 Handle 3599000286 2 Positive (RED) Cable w/clamps 3899001519 3 Negative (BLACK) Cable w/clamps 3899001520 4 ...
-
Sears 200.71233 - page 5
4 Attach Foot: Remove charger from packing materials and place charger face down. Attach mounting foot and secure with the two, 1/4-20 thread cutting screws provided. continued on next page Before Using Y our Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect t ...
-
Sears 200.71233 - page 6
5 Axle Assembly (continued) : Place the charger on its side. Place one end of each bracket into slot, then place the axle assembly under each bracket. Fasten the other side of each bracket using the two, 10-32 thread cutting screws provided. WARNING Plugging it in Electrical Shock Hazard Be sure that power cord fits properly into outlet. If not, ha ...
-
Sears 200.71233 - page 7
6 MINIMUM RECOMMENDED EXTENSION CORD Length of Cord, in Feet 25 50 100 150 AWG* Size of Cord 16 14 10 8 *AWG=American Wire Gauge Using an e xtension cord The use of an extension cord is not recommended. If you must use an extension cord, please make sure that you follow these guidelines: • Make sure the pins on the plug of the extension cord are ...
-
Sears 200.71233 - page 8
7 To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle. Using Y our Battery Charger Follow these instructions to obtain the accurate charge level for your battery. TOUCH PAD CONTROLS AND DIGITAL DISPLAY The touch p ...
-
Sears 200.71233 - page 9
8 12V ALTERNATOR/GENERATOR DISPLAY 14 – 15 volts = Good condition 12.8 or less volts = Check with qualified technician 12.8 - 14 volts or = See vehicle owner’s 15 volts or more manual NOTE: If the digital display reads less than 12.8 volts, the charging system may have loose fan belts, a defective voltage regulator or alternator. Additional tes ...
-
Sears 200.71233 - page 10
9 Using the engine start feature The Engine Start is a feature to help start the engine of your vehicle: 1. Push the switch located on the front panel to CHARGE/TEST. 2. Push SELECT BUTTON and choose 125A START (6 volt) or 225A START (12 volt). The ENGINE START feature will deliver 125 amps to help crank a 6-volt system and 225 amps to help crank a ...
-
Sears 200.71233 - page 11
10 Charging Y our Battery NO TE: A marine (boat) boat batter y must be remov ed and charged on shore. T o charge it on board requires equipment specially designed for marine use. Charging your battery in the vehicle: 1. Arrange the power cord and charging cords care- fully in order to avoid damage that could be caused by the hood, door, or moving e ...
-
Sears 200.71233 - page 12
11 Charging your battery outside the vehicle: NO TE: A marine (boat) must be remov ed and charged on shore. T o charge it on board requires equipment specially designed f or marine use. 1. Remove battery from vehicle, making sure to dis- connect grounded terminal first with all power turned off to the vehicle. 2. Check the polarity of the battery p ...
-
Sears 200.71233 - page 13
12 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED . Find your battery’s rating on the chart below and note the charge time given for each charger setting. The times given are for batteries with a 50-percent charge prior to recharg ...
-
Sears 200.71233 - page 14
13 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on Digital A C cord and/or extension Check A C outlet and e xtension cords for loose fitting Displa y , charger f an cord i ...
-
Sears 200.71233 - page 15
14 For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). ...
¿Tienes una pregunta acerca de Sears 200.71233?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 200.71233, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 200.71233 probablemente compartirá una forma de solucionarlo.