-
Renesas H8S/2138 Series - page 1
H8S/2138 Series TQFP-80C User System Interface Cable (HS2138ECN61H) for E6000 Emulator User’s Manual HS2138ECN61HE(C) ...
-
Renesas H8S/2138 Series - page 2
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property ...
-
Renesas H8S/2138 Series - page 3
i Preface Thank you for purchasing this user system interface cable (HS2138ECN61H) for the Renesas’s original mi crocomputer H8S/2138 series. The HS2138ECN61H is a user system interface cable that connects an H8S/2148, H8S/2138, H8S/2128 series E6000 emul ator (HS2148EPI61H; hereinafter referred to as the emulator) t o the IC socket for a TQFP-80 ...
-
Renesas H8S/2138 Series - page 4
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 4 2.1 Connecting User System Interf ace Cable to Em ulat or Station ......................................... 4 2.2 Connecti ...
-
Renesas H8S/2138 Series - page 5
1 Section 1 Configuration CAUTION Use an IC149-080-058-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-80C package IC socket on the user system. Figure 1 shows the configuration of the HS2138E CN61H user system interface cable for the TFP-80C package. ...
-
Renesas H8S/2138 Series - page 6
2 (for fastening cable head) User system IC socket Cable head Screws (M2.6 x 12 mm) with flat washers Screws (M2.6 x 8 mm) with flat washers Socket cover To emulator station Cable body Figure 1 HS2138ECN61H User System Interface Cable ...
-
Renesas H8S/2138 Series - page 7
3 Table 1 lists t he HS2138ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2138ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Includes flat cable 2 Cable head 1 3 IC socket 1 For the TFP-80C package 4 Socket cover 1 For installing an TFP-80C packaged MCU 5 Screws (M2.6 x 12 mm) 4 For ...
-
Renesas H8S/2138 Series - page 8
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so w ill damage ...
-
Renesas H8S/2138 Series - page 9
2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so w ill damage the user system and the emulator pro ...
-
Renesas H8S/2138 Series - page 10
6 2.2.4 Fastening Cable Head CAUTION 1. Use a Phillips-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a scr ...
-
Renesas H8S/2138 Series - page 11
Cable head User system IC socket (IC149-080-058-B51 manufactured by YAMAICHI ELECTRONICS Co. Ltd.) Screws (M2.6 x 12 mm), flat washer Pin 1 Figure 3 Connecting User System Interface Cable to User System 7 ...
-
Renesas H8S/2138 Series - page 12
2.2.5 Connecting Cable Body to Cabl e Head Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 4 Fastening Cable Body 8 ...
-
Renesas H8S/2138 Series - page 13
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-80C package (IC149-080-058-B51: m anufactured by YAM AICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewh at different from those of the actual chip ...
-
Renesas H8S/2138 Series - page 14
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Unit: mm Tolerance: –0.5 mm Figure 6 Dimensions for User System Interface Cable Head 10 ...
-
Renesas H8S/2138 Series - page 15
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. Cable head User system Unit: mm Tolerance: –0.5 mm IC socket (IC149-080-058-B51 manufactured by YAMAICHI ELECTRONICS Co. Ltd.) Figure 7 Resulting Dimensi ...
-
Renesas H8S/2138 Series - page 16
12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes ...
-
Renesas H8S/2138 Series - page 17
MCU Pin 1 IC socket (IC149-080-058-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2.6 x 8 mm) with flat washers Socket cover Figure 8 Installing MCU to User System 13 ...
-
Renesas H8S/2138 Series - page 18
Section 4 Verifying Operation 1. When using the E6000 emulator (HS2148EPI61H) for t he H8S/2148, H8S/2138, H8S/2128 series, turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User' s Manual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal m emory and por ...
-
Renesas H8S/2138 Series - page 19
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifi ...
¿Tienes una pregunta acerca de Renesas H8S/2138 Series?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Renesas H8S/2138 Series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Renesas H8S/2138 Series probablemente compartirá una forma de solucionarlo.