-
Rubbermaid 1S84 - page 1
RUBBERMAID 7' x 10' 6" RESIN STORAGE BUILDING ASSEMBL Y INSTRUCTIONS Pre-Assembly: • Review the parts list and make sure that no parts are missing. • Review ALL assembly steps before beginning instructions. • Level the area where the shed will be located. • Areas of "fill dirt" should be tamped/compacted to prevent ...
-
Rubbermaid 1S84 - page 2
Level construction site before beginning assembly of shed. A foundation may be constructed if desired. 1 FLOOR PLAN: Size the construction site to fit the entire floor . Allow clearance for opening front and back doors. OPTIONAL STEP: If desired, recessed anchor locations (8 places) can be used to anchor the shed floor to a foundation after Step 6. ...
-
Rubbermaid 1S84 - page 3
3 Place the Floor Panel (J-5H51) on the foundation. Connect two Repeat Floor Panels (K-5H52), install Screws (AA) 14 places. Optional Step: If desired, recessed anchor locations (8 places) can be used to secure the Floor to the Foundation, see Step 1. Using a utility knife, cut the long sides of each wall slot tab and then use a screwdriver to knoc ...
-
Rubbermaid 1S84 - page 4
5 Using a screwdrive r , punch out the screw holes on the top of Left Side Panel (C) 2 places . Connect Left Side Panel (C) into Front Floor (J-5H51). C C Screw Holes click 6 Lubricate dovetails on Left Front Panel (H) 4 places with liquid soap. Connect Left Front Panel (H) into dovetails of Left Side Panel (C), engage snaps on bottom of Left Front ...
-
Rubbermaid 1S84 - page 5
9 Using a screwdriver , punch out the screw holes on the top of the Left Side Panel (C) 2 places. Align lap joint between Left Side Panels. Connect Left Side Panel (C) into Repeat Floor (K-5H52). C C C C click 10 Install Wall Connectors (Q) 5 places. 2 1 C C 1 2 C Q C 11 Lubricate dovetails on Left Back Panel (E) 4 places with liquid soap. Connect ...
-
Rubbermaid 1S84 - page 6
13 14 15 16 Lubricate dovetails on Right Back Panel (G) 4 places with liquid soap. Connect Right Back Panel (G) into dovetails of Right Side Panel (D), engage snaps on bottom of Right Back Panel (G) into Repeat Floor (K-5H52). E G D 1 2 1 2 NOTE: Front Gable and Doors not shown. Engage lap joint between Left Back Panel (E) and Right Back Panel (G) ...
-
Rubbermaid 1S84 - page 7
17 18 19 20 Set the Left Door Panel (AK) face down on the ground. Slide the Hinge Reinforcement (PP) into the hole on the top door pin. The Hinge Reinforcement (PP) will slide in until it is below the end of the door pin. AK PP AK AK PP Starting at the top of the door , slide the Door Reinforcement (NN) onto the groove located on the handle side of ...
-
Rubbermaid 1S84 - page 8
21 22 23 24 Install Left Door Panel (K) inserting the lower hinge pin into Front Floor (J-5H51) socket, lift the left end of the Gable (M) enough to insert the top hinge pin on Left Door Panel (K) into the Gable (M) socket. M 3 1 2 K 4 Install Right Door Panel (F) inserting the lower hinge pin into Front Floor (J-5H51) socket, lift the right end of ...
-
Rubbermaid 1S84 - page 9
25 26 27 28 Apply Ridge T ape (HH) to Ridge Cap (GG) 2 places. Snap Ridge Cap (GG) onto the Ridge Beam Assembly covering the seam. GG HH HH GG RS RL GG RS RL Place the Ridge Beam Assembly into cups at the top of each Gable (M). Align slots in Ridge Beam Assembly with holes in Gable (M) tab at back, install Bolt (BB), Washer (CC), and Nut (DD) 1 pla ...
-
Rubbermaid 1S84 - page 10
29 30 Align slots in Ridge Beam Assembly with holes in Gable (M) tab, install Bolt (BB), Washer (CC), and Nut (DD) 1 place, ONL Y TIGHTEN NUT “FINGER” TIGHT . Bolt Head Washer Nut Plastic T ab on Gable DD CC BB M M R Using a screwdrive r , punch out the screwholes on the Left Skylight Roof Panel (AN ) 6 places. Attach the Skylight (L) to the Le ...
-
Rubbermaid 1S84 - page 11
Lubricate roof snaps on left side of the front Gable (M) 4 places. Raise the Left Roof Panel (N) onto the left side of the shed assembly , the arrows on the Roof Panel should face the inside of the shed and point towards the Ridge Beam Assembly . R M N 31 32 Using (2) stepstools (1 inside shed, 1 outside shed), lift the bottom of the Roof Panel abo ...
-
Rubbermaid 1S84 - page 12
Raise the Left Skylight Roof Panel (AN) onto the left side of the shed assembly , the arrows on the Roof Panel should face the inside of the shed and point towards the Ridge Beam Assembly. Using (2) stepstools (1 inside shed, 1 outside shed), lift the bottom of Left Skylight Roof Panel (AN) above horizontal and guide into the Ridge Beam Assembly . ...
-
Rubbermaid 1S84 - page 13
Install Roof Connectors (T) 8 places. Y ou may need to lift the roof panels to avoid the 2"x6" lumber . 35 T 1 2 2 1 Engage all snaps between the Roof Panels and Gables. Then engage all snaps between Roof Panels and Wall Panels. 36 1 1 2 2 ...
-
Rubbermaid 1S84 - page 14
Repeat Steps 29-35 for Right Roof of shed. 37 Install Screws (AA) 16 places in front and back Gable (M). 38 Back of shed shown Caution: When installing screws do not overtighten. See Steps 30, 31 See Step 29 See Step 32 See Step 33 AA (16) AP P P N R P L While 1 person holds down the bottom of the Roof, install Screws (AA) 12 places in screw holes ...
-
Rubbermaid 1S84 - page 15
88.09" 128.85" 94.63" ...
-
Rubbermaid 1S84 - page 16
Customer Service T oll Free: 1-888-895-2110 M–F 8:30 AM to 5:00 PM EST or visit us at www .rubbermaid.com 1869756 W e hope you enjoy your Rubbermaid ® 7' x 10' 6" Storage Building! For more information on all Rubbermaid ® products, go to www .rubbermaid.com Printed in U.S.A. © 2012 Rubbermaid Incorporated Huntersville, NC U.S.A. ...
¿Tienes una pregunta acerca de Rubbermaid 1S84?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Rubbermaid 1S84, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Rubbermaid 1S84 probablemente compartirá una forma de solucionarlo.