-
EverFocus EPTZ100 - page 1
EPTZ 100 Day / Night Speed Dome Camera INSTALLATION / OPERATION ...
-
EverFocus EPTZ100 - page 2
EPTZ100_ma_en_ rev03.do c 2 1 SAFETY WARNINGS • Do not place the device near to heaters, furnaces, other heat sou rces or under direct solar irradiation. • Operate the device only in locations providing the tolerable operating temperature r ange 0°C~40°C. • For cleaning, make sure the device is plugged off and only use a damp cloth without ...
-
EverFocus EPTZ100 - page 3
EPTZ100_ma_en_ rev03.do c 3 TABLE OF CONTENTS 1 SAFETY WARNINGS ................................................................................................................ 2 2 INTRODUCTION ...................................................................................................................... 5 2.1 Features ...................... ...
-
EverFocus EPTZ100 - page 4
EPTZ100_ma_en_ rev03.do c 4 5.2.6 Remote switching of EPTZ 100 output rel ay ................................................................. 44 6 APPENDIX A: Basic Settings at EKB 500 keyboard .................................................................... 45 6.1 COM PORT SETTING - RS-485 interface setting ................................... ...
-
EverFocus EPTZ100 - page 5
EPTZ100_ma_en_ rev03.do c 5 2 INTRODUCTION The mini PTZ speed dome EPTZ 100 provides ideal d iscreet surveillance for CCTV indoor applications. Engineered with the latest Digital Slow Shutte r (DSS) x128 technology, EPTZ 100 can impro ve CCD sensitivity, producing quality images also unde r low light conditions. EPTZ 100 offers enhanced features su ...
-
EverFocus EPTZ100 - page 6
EPTZ100_ma_en_ rev03.do c 6 2.4 SPECIFICATIONS Camera Sensor: 1/4” CCD SONY Super HAD Effective pixels: 380.000 (NTSC), 440.000 (PAL) Horizontal resolution: 520 TV lines (colour mode) 570 TV lines (b/w mode) Sensitivity: 0,7 lux (F 1.8, 50 IRE – colour mode) 0,02 lux (F 1.8, 50 IRE – b/w mode) 0.005 lux ( DSS x 128) Video output: Composite 1 ...
-
EverFocus EPTZ100 - page 7
EPTZ100_ma_en_ rev03.do c 7 Alarm: 3 inputs, 1 output, with tour / position auto triggering Proportional pan speed: yes Privacy zones: 4 zones, free adjustable Setup: multiline OSD setup menu Auto resume: after 1, 2, 3, 4, 5 or 10 min. no activity: go to Video output: BNC cable socket Power Power source: 24 V AC +/- 10% Power consumption: 19 W max. ...
-
EverFocus EPTZ100 - page 8
EPTZ100_ma_en_ rev03.do c 8 2.5 DIMENSIONS 2.5.1 Dimensions with ceiling mount adapter 2.5.2 Dimensions with recessed ceiling mount adapter 114 170 54 202 114 80 115 ~150 166 ...
-
EverFocus EPTZ100 - page 9
EPTZ100_ma_en_ rev03.do c 9 2.5.3 Dimension EPTZ 100 with wall mount bracket EPTZ 100 WLM 2.5.4 Dimensions wall bracket EPTZ 100 WLM 270 225 169,5 140 240 140 120 60 80 240 80 ...
-
EverFocus EPTZ100 - page 10
EPTZ100_ma_en_ rev03.do c 10 2.5.5 Dimension EPTZ 100 with ceiling pendant bracket EPTZ 100 CPM 2.5.6 Dimension ceiling pendant bracket EPTZ 100 CPM 500 120 100 300 72 80 80 ...
-
EverFocus EPTZ100 - page 11
EPTZ100_ma_en_ rev03.do c 11 3 INSTALLATION 3.1 MECHANICAL 3.1.1 Ceiling mount The ceiling mount accessories a re included in the EPTZ 100 package. 1. Use the drilling template to mark the drilling holes. 2) Click the connector boa rd into the ceiling adapter. Follow the red arrow ma rks at board and ceiling adapter for correct position. 3) Mount t ...
-
EverFocus EPTZ100 - page 12
EPTZ100_ma_en_ rev03.do c 12 3.1.2 Recessed ceiling mount Recessed ceiling mount is possibl e at open ceilings. A metal ring has to be mounted at ceiling side. 1) Cut a 115mm / 4.6" hole into the ceiling. 2) Drill 3 screw holes for mounting in the ceili ng Use the metal ring as template for drilling holes. 3) Plug the connector board to the do ...
-
EverFocus EPTZ100 - page 13
EPTZ100_ma_en_ rev03.do c 13 3.1.3 Wall mount Wall mount requires the optional bracket EPTZ 100 WLM. 1) Assemble the connector board to the bra cket adapter by 3 M4 screws. Follow the red arrow marks at both board and ceiling adapter for correct position. 2) Remove the cable cover from the wall bracket. 3) Mount the bracket adapter with connector b ...
-
EverFocus EPTZ100 - page 14
EPTZ100_ma_en_ rev03.do c 14 3.1.4 Ceiling pendant mount Ceiling pendant mount require s the optional adaptor EPTZ 100 CLM. 1) Assemble the connector board to the bra cket adapter by 3 M4 screws. Follow the red arrow marks at board and ceiling adapter for correct po sition. 2) Mount the bracket adapter with the co nnector board to the EPTZ 100 CLM. ...
-
EverFocus EPTZ100 - page 15
EPTZ100_ma_en_ rev03.do c 15 3.2 ELECTRICAL 3.2.1 Video EPTZ 100 provides a composite 1 Vp-p video out put PAL/NTSC (v ideo system depending on ordered version) with a BNC cable socket. Cameras and video displ aying or processing equipm ent (DVRs, switchers etc.) re quire cabling with 75 Ohm video cable, e.g. RG-59, RG -12, and suitable BNC plugs. ...
-
EverFocus EPTZ100 - page 16
EPTZ100_ma_en_ rev03.do c 16 3.2.3 RS-485 EPTZ 100 uses RS-485 simplex wiri ng; the signal is transferred via a single twisted pair line. CAT5 network cable is recomm ended, UTP version (u nshielded) is sufficient for normal application. A shielded cable should be used if the install ed cabl es are expected to be highly susceptible to interferences ...
-
EverFocus EPTZ100 - page 17
EPTZ100_ma_en_ rev03.do c 17 3.2.3.1 RS-485 installation with EKB 500 keyboard For connection to EKB 500 via RS-485, it is recommended to use the EKB 500 connector box. The drawing below shows an installation example. Please make sure that the wires are connected with correct pol arity. Alternatively, it is possible to connect the RS-485 wire direc ...
-
EverFocus EPTZ100 - page 18
EPTZ100_ma_en_ rev03.do c 18 3.2.3.2 RS-485 installation with EverFocus DVR It is possible to control the EPTZ 100 speed dome by EverFocus DVR (except 1 Ch. models) via network. A combined local control by EKB 500 keyboard and remote (network) cont rol by DVR is also possible. For a combined local and remote PTZ control, it is mandatory that DVR an ...
-
EverFocus EPTZ100 - page 19
EPTZ100_ma_en_ rev03.do c 19 3.2.4 Alarm EPTZ 100 provides 3 alarm input contac ts and 1alarm output rela y. It is also possible to trigger the alarm output relay by EKB 500 keyboard command. For input contacts, use dry Normal Open (N.O.) contacts only. The maximum load of output relay contacts is 30 V AC/DC 0.5 A max. ...
-
EverFocus EPTZ100 - page 20
EPTZ100_ma_en_ rev03.do c 20 3.3 COMMUNICATION SETTINGS The setup for general RS-485 parameters - protocol type, RS-485 address and baud rate - is done by DIP switches, located at the top of the camera module. Correct settings are essential for communicatio n with the dome controller. For correct communication, all 3 parameters - protocol , baud ra ...
-
EverFocus EPTZ100 - page 21
EPTZ100_ma_en_ rev03.do c 21 3.3.2 RS-485 ID (address) The RS-485 ID (address) setting is done by DIP swit ch DS2. The following table shows the switch positions for the possi ble addresses 1 ~ 255: ...
-
EverFocus EPTZ100 - page 22
EPTZ100_ma_en_ rev03.do c 22 ...
-
EverFocus EPTZ100 - page 23
EPTZ100_ma_en_ rev03.do c 23 3.3.3 RS-485 bus termination The last device in an RS-485 bus sh ould be terminated by 120Ohm resi stor to avoid reflections on the bus (for details, please refer to chapter 3 .2.3). The termination is done by DIP switch DS3. Termination ON Termination OFF 3.4 INITIAL START After finishing all installation steps, power ...
-
EverFocus EPTZ100 - page 24
EPTZ100_ma_en_ rev03.do c 24 4.1.2 Menu Struc ture OSD Structure Part 1: PATROL PRESET SPEED DWELL RUN MAIN MENU SYSTEM INFO DISPLAY CAMERA SCAN CONTRO L PRIVACY MASK ALARM INITIALIZE EXIT SYSTEM INFO TYPE FIRMWARE BAUDRATE RS-485 ID PROTOCOL DISPLAY CAMERA ID CAMERA NAME PRESET NUMBER PRESET NAME PTZ POSITION CA MERA ZOOM SPEED ADVANCED SETUP RESC ...
-
EverFocus EPTZ100 - page 25
EPTZ100_ma_en_ rev03.do c 25 OSD Structure Part 2: MAIN MENU SYSTEM INFO DISPLAY CAMERA SCAN CONTRO L PRIVACY MASK ALARM INITIALIZE EXIT CONTRO L AUTO RESUME POWER ON RESUME IMAGE FLIP PRIVACY MASK MASK 1 MASK 2 MASK 3 MASK 4 AL ARM RELAY INPUT 1 INPUT 2 INPUT 3 OUTPUT INITIALIZE POWER ON RESET CAMERA DEFAULT FACTORY DEF AULT LENS REFRESH CAMERA RE ...
-
EverFocus EPTZ100 - page 26
EPTZ100_ma_en_ rev03.do c 26 4.1.3 Main menu After opening OSD setup the MAIN me nu is shown at the scree n: MAIN MENU SYSTEM INFO DISPLAY CAMERA SCAN CONTRO L PRIVACY MASK ALARM INITIALIZE EXIT Select a menu item with UP/DOWN, RIGHT will open subm enu. NOTE: The OSD menu has a timeout f unction. After 2 minutes with no activity, the OSD menu will ...
-
EverFocus EPTZ100 - page 27
EPTZ100_ma_en_ rev03.do c 27 4.1.6 Camera This menu provides the camera video settings. CA MERA ZOOM SPEED Zoom speed setup in 8 possible levels: Level 1: slowest to Level 8: fastest ADVA NCED SETTI NG Opens submenu for camera features (following chapter) RESCUE MODE Mode for recovering serial communication between speed dome and camera module. Thi ...
-
EverFocus EPTZ100 - page 28
EPTZ100_ma_en_ rev03.do c 28 some blue or reduce som e red; if lighting is fluorescent or within white spectrum, try to either add some red or redu ce some blue. Default values are 30 (for RED) and 40 (for BLUE); it is recomm ended not to set the values too far away from these two default values. BACKLIGHT Back light compensation improves the ima g ...
-
EverFocus EPTZ100 - page 29
EPTZ100_ma_en_ rev03.do c 29 ZOOM POS INIT Defines a zoo m position after powering u p the camera, range is x1 ~ x10 LENS INIT Reset of the autofocus lens in case of malfunctio n END Return to CAMERA ADVANCED SETTING page EXPOSURE BRIGHTNESS Image brightness setting, range 1~100 IRIS Mode of the lens iris: AUTO : automatic iris mode MANUAL : manual ...
-
EverFocus EPTZ100 - page 30
EPTZ100_ma_en_ rev03.do c 30 SPECIAL Submenu for advanced camera fun ctions: USER PRESET Not supported by EPTZ 100 PRIVACY Keep OFF setting, privacy mask setup is done in the PRIVACY MASK menu, available in the main menu DAY/NIGHT Modes of the day/night switching: B/W : black/white (night) mode, IR cut filter switched off COLOUR : colour (day) mode ...
-
EverFocus EPTZ100 - page 31
EPTZ100_ma_en_ rev03.do c 31 4.1.7 Scan This menu contains all setup option s for automatic dome modes such as autopan, preset tours and pattern. SCAN AUTO PAN ALL PRESET GROUP SCAN TOUR SCAN PATROL PATTERN AUTO PAN PAN/TILT This autopan mode performs pan and tilt movements between 2 points. The vertical movement will be processed in programmed spe ...
-
EverFocus EPTZ100 - page 32
EPTZ100_ma_en_ rev03.do c 32 RETURN Return to AUTO PAN menu. CIRCLE This autopan mode performs a continuous h orizontal 360° movement. TILT LEVEL Adjust the vertical position of the camera, press IRIS - to store the vertical angle. SPEED Autopan speed, range from 2 (slowe st) to 180 (fastest). RUN Autopan start (this function will clo se OSD menu) ...
-
EverFocus EPTZ100 - page 33
EPTZ100_ma_en_ rev03.do c 33 TOUR SCAN Combined preset tour with sele cted GROUP tours. GROUP1 ON: Group1 included in tour OFF: Group1 skipped in tour GROUP2 ON: Group 2 included in tour OFF: Group 2 skipped in tour GROUP3 ON: Group3 included in tour OFF: Group3 skipped in tour GROUP4 ON: Group4 included in tour OFF: Group4 skipped in tour SPEED Pa ...
-
EverFocus EPTZ100 - page 34
EPTZ100_ma_en_ rev03.do c 34 PATTERN A pattern is a programmed course of camera movement. EPTZ 100 can store 4 patterns with a maximum length of 10 minutes each. 1~4 Select a pattern for programming / che cking. RECORD Start the movement progra mming with "Go To Preset 1". All manual movements / zoomings are recorded now. The TIMER in the ...
-
EverFocus EPTZ100 - page 35
EPTZ100_ma_en_ rev03.do c 35 4.1.8 Control This menu provides settings for resu me function after inactivity, power-up and special functions. AUTO RESUME OFF/ON > AUTO RESUME is the reaction of the dome after a defined time of inactivity (no operator action). ON: auto resume activated OFF: auto resume not active MODE Type of resume reaction: AP( ...
-
EverFocus EPTZ100 - page 36
EPTZ100_ma_en_ rev03.do c 36 4.1.9 Privacy Mask EPTZ 100 allows for masking 4 different area s to protect private or confidential zones in the field of view. MASK1~4 OFF/ON shows the status of the privacy zone: ON : privacy zone masking active OFF : privacy zone off RIGHT enters the submenu to mask setup POSITION Definition of size and position of ...
-
EverFocus EPTZ100 - page 37
EPTZ100_ma_en_ rev03.do c 37 4.1.10 Alarm In this menu, the alarm reactions for input contacts a re defined. 4.1.11 Initialize RELAY OFF/ON It is possible to switch the output relay remotely with this menu item for test purpose: ON: output relay switched OFF: output relay not active (off) INPUT1...3 PRESET x Assignment of the preset position which ...
-
EverFocus EPTZ100 - page 38
EPTZ100_ma_en_ rev03.do c 38 5 OPERATION WITH EKB 500 KEYBOARD The following chapter de scribes the EPTZ 100 operation with EKB 500 keyboard (with firmware 1.5 or higher). EPTZ 100 is optimized for protocol type EVF-2 of EKB 500 keyboard. Basic communication settings for EKB 500 are described in APPENDIX A. For further details, please refer to the ...
-
EverFocus EPTZ100 - page 39
EPTZ100_ma_en_ rev03.do c 39 5.1 EKB 500 OPERATION WITH EVERFOCUS PROTOCOL (EVF-2) Operation outline Function Keys / operation Open dome menu M M M E E E N N N U U U or C C C A A A M M M (hold) + M M M E E E N N N U U U (if main monitor of DVR is selected) or S S S H H H I I I F F F T T T (hold)+ P P P O O O S S S I I I T T T I I I O O O N N N > ...
-
EverFocus EPTZ100 - page 40
EPTZ100_ma_en_ rev03.do c 40 Speed:___[1-239] [ENT] to start. 5.1.1 EPTZ 100 setup menu Start EPTZ menu: If DVR Main monitor is selected ("DVR" in LCD display): C C C A A A M M M (hold) + M M M E E E N N N U U U If no DVR main monitor is selected: M M M E E E N N N U U U or C C C A A A M M M (hold) + M M M E E E N N N U U U or alternative ...
-
EverFocus EPTZ100 - page 41
EPTZ100_ma_en_ rev03.do c 41 5.1.4 Preset tours EPTZ 100 provides 7 different preset tour mode s. All tours are defined in OSD setup menu. 1. PATROL TOUR: Preset tour with up to 16 selected p resets. 2. ALL PRESET TOUR: Preset tour with all available presets. 3. GROUP 1 TOUR: Preset tour with presets 1~4 4. GROUP 2 TOUR: Preset tour with presets 1~ ...
-
EverFocus EPTZ100 - page 42
EPTZ100_ma_en_ rev03.do c 42 5.2 EKB 500 OPERATION WITH PELCO-D/P PROTOCOL NOTE: Not all EPTZ 100 functions are av ailable in PELCO-D /P protocol. Operati on for ssome functions is different to operation with EVERFOCUS protocol. 5.2.1 EPTZ 100 setup menu Start EPTZ 100 menu: If DVR Main monitor is selected ("DVR" in LCD display): C C C A ...
-
EverFocus EPTZ100 - page 43
EPTZ100_ma_en_ rev03.do c 43 5.2.3 Autopan The speed for autopan function is programmed in the OSD menu; t he entered value for speed in EKB 500 will be ignored at start of autopan. Activate A-B autopan (pan/tilt between 2 points) A A A . . . P P P A A A N N N (Pelco-P only) Alternative: P P P O O O S S S I I I T T T I I I O O O N N N > 9 9 9 9 ...
-
EverFocus EPTZ100 - page 44
EPTZ100_ma_en_ rev03.do c 44 5.2.6 Remote switching of EPTZ 100 output relay The EKB 500 keyboard provides the option to switch the output relay of EPTZ 10 0 On / Off. Switch relay ON: F F F 4 4 4 > > > [ [ [ 1 1 1 ] ] ] > > > E E E N N N T T T E E E R R R Alternative: P P P O O O S S S I I I T T T I I I O O O N N N > 8 8 8 2 2 ...
-
EverFocus EPTZ100 - page 45
EPTZ100_ma_en_ rev03.do c 45 Video Connected to DVR: _ _ _ CH : _ _ 6 APPENDIX A: BASIC SETTING S AT EKB 500 KEYBOARD The following chapter de scribes the basic setting s in the EKB 500 keyboard to establish communication with speed dome cameras. 6.1 COM PORT SETTING - RS-485 INTERFACE SETTING Telemetry protocol type and transmi ssion rate are defi ...
-
EverFocus EPTZ100 - page 46
EPTZ100_ma_en_ rev03.do c 46 7 APPENDIX B: BASIC SET TINGS AT EVERFOCUS DVR The following settings are required to establish RS-485 comm unication between DVR and speed dome: 7.1 EDR / EDVR / EDSR SERIE S (EXCEPT EDSR100, EDSR100H) 1. CAMERA menu: enter the correct RS -485 ID (address) at the speed dom e camera channel. 2. CONTROL menu: under " ...
-
EverFocus EPTZ100 - page 47
EPTZ100_ma_en_ rev03.do c 47 8 APPENDIX C: TROUBLESHOOTING 8.1 GENERAL MALFUNCTION In case of drifted preset position or ab normal reaction of EPTZ 100 speed dome pe rform a reset of the dome, for t he reset 3 options are possib le: Option 1: Setup menu > INITIALIZE > POWER ON RESET Option 2: (GoTo) POSITION 80 Option 3: Power off dome for mi ...
-
EverFocus EPTZ100 - page 48
EPTZ100_ma_en_ rev03.do c 48 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan www.everfocus.com.tw USA Subsidiary : 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. www.everfocus.com European Subsidiary: Albert-Einstein-Straße 1 D-46446 Emmerich am Rhein, Germany www.everfocus.de China Subsidi ...
¿Tienes una pregunta acerca de EverFocus EPTZ100?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con EverFocus EPTZ100, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con EverFocus EPTZ100 probablemente compartirá una forma de solucionarlo.