-
N-Tron 400 Series - page 1
Rev 041008 1 400 Series Industrial Ethernet Switches Installation Guide ...
-
N-Tron 400 Series - page 2
Rev 041008 2 Industrial Ethernet Switch In stallation Guid e 405TX 405FX-SC 405FX-ST 405FXE-SC-YY 405FXE-ST-YY Where: YY = -15, -40, or -80 ...
-
N-Tron 400 Series - page 3
Rev 041008 3 Copyright, © N-TRON Corp., 2 008 820 S. University Blvd., Suit e 4E Mobile, AL 36609 USA All r ights r eserved. Reproduction, adaptation, or translation without prior wri tten permissio n fro m N-TR ON Corp. is prohibited, exc ept as allowed under copyright laws. Ethernet is a registered trademark of Xerox Corporation. All other produ ...
-
N-Tron 400 Series - page 4
Rev 041008 4 Safety Warnings ELECTRICAL SAFETY WARNING: Do not di sconnect while circuit is live, un less area is known to be non- hazardous. WARNING: Disconn ect the power cable before removing the en closure top. WARNING: Do not opera te the unit with the top cover removed. WARNING: Do not wor k on equipment or cables du ring periods of lightnin ...
-
N-Tron 400 Series - page 5
Rev 041008 5 405FX, 405FXE, & 405 TX Industrial Et hernet Switches The 405TX and 405FX Un managed Industrial Ethernet Switches support high speed layer 2 switching between ports. The 405TX is an a ffordable 5 po rt unmanage d s witch that is ca pable of auto negotiat ing 10/100 Mb an d half/full duplex c ommunications. The N-TRON 405TX i s hou ...
-
N-Tron 400 Series - page 6
Rev 041008 6 PACKAGE CONTENTS Please make sure the Ethernet Switch package contains the following items: 1. 405FX/405FXE/405TX Et hernet Switch 2. This Installation Guide Contact your carrier if any it ems are damaged. INSTALLATION Read the following warning be fore beginning the installation: WARNING The 405FXE unit co ntains a Class 1 Laser. Do n ...
-
N-Tron 400 Series - page 7
Rev 041008 7 405FX/405FXE HALF DUPLEX SETUP While all RJ45 ports are Autosensing, the 405FX/405FXE Fi ber Optic Port i s factory configured for full duplex operation. In t he event half duplex operation i s desired, follow these steps: 1. Remove the Voltage Input Power Plugs. 2. Remove the top cove r (8 screws). 3. Remove the jumper plug ( JP1) fro ...
-
N-Tron 400 Series - page 8
Rev 041008 8 DIN-Rail Mounting Install the unit in a standard DIN-Rail. Reces s the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius (2” for TX models). Note: This unit may be mounted horizontally or ver tically. To install the unit to 35mm indu strial DIN-Rail - Place the top edge of the included mounting b r ...
-
N-Tron 400 Series - page 9
Rev 041008 9 FRONT PANEL From Left to Right: LNK Link LED for Fiber Optic Port (405FX/FXE only) TX Fiber Optic Transmit Port ( 405FX/FXE Only) RX Fiber Optic Receive Port ( 405FX/FXE Only) ACT Acti vity LED for Fiber Optic Po rt (405FX/FXE only) X RJ45 Crossover Upli nk Port (405TX Only) RJ45 Ports Auto sensing 10/100Base T Connections ! Red LED in ...
-
N-Tron 400 Series - page 10
Rev 041008 10 LED’s: The table below desc ribes the operating modes: LED Color Description GREEN Power is Applied OFF Power is OFF ! RED Controller HW Error OFF No Errors. Normal Operation. LNK GREEN Link between ports established OFF No Link between ports ACT GREEN Data is active betwee n ports OFF Data is inactive bet ween ports APPLYING POWER ...
-
N-Tron 400 Series - page 11
Rev 041008 11 N-TRON SWITCH GRO UNDING TECHNIQ UES The grounding philosophy of any control sys tem is an integral part of t he design. N-Tron switches are designed to be gro unded, but the us er has been given the fle xibility to floa t the switch when requi red. The bes t noise immunity and e missions ( i.e. CE) are obtained when the N-Tron swit c ...
-
N-Tron 400 Series - page 12
Rev 041008 12 RJ45 CONNECTOR CRI MP SPECIFICATIO NS Please reference the illustrati on below for your Cat5 cable specific ations: ...
-
N-Tron 400 Series - page 13
Rev 041008 13 CONNECTING THE UNIT For 405FX & 4 05FXE units, remove th e dust cap from the fiber optic connectors and conn ect the fiber optic cables. The TX port o n t he 405FX should be connected t o t he RX port of the far end st ation. The RX port on the 405FX sho uld be connected to the TX port of the far end station. For 10/100 Base-TX po ...
-
N-Tron 400 Series - page 14
Rev 041008 14 KEY SPECIFICATIONS Physical Height: 2.13" (5.41 cm) Width: 5.00" (1 2.70 cm) Depth: 3.00" (7.62 cm) Weight: ~ 1.2 lbs. (0.6 kg) (Note: can be mounted hori zontally or vertically) Electrical Input Voltage: 10-30 VDC (Reg ulated) Input Current: 220mA max. @ 24VDC (Ste ady State) Inrush Current: 14.0Amp/0.9ms max. @ 24VDC ...
-
N-Tron 400 Series - page 15
Rev 041008 15 Regulatory Approvals: Safety: UL 1604 (US and Cana da) Hazardous Locati ons, Class I, Zone 2, Group IIC, T4A EMI: EN55022 – Cl ass A FCC Part 15 Class A EMS: EN55024:1998 EN61000-4-2:1995 EN61000-4-3:1997 EN61000-4-4:1995 EN61000-4-5:1995 EN61000-4-6:1996 GOST-R Certified. Warranty: Effective Januar y 1, 2008, all N-TRON products ca ...
-
N-Tron 400 Series - page 16
Rev 041008 16 N-TRON Limited Warrant y N-TRON, Corp. warrants to the end user that this hardware product will be fr ee from defects in workmanship and materials, under normal u se and service, for the applicable war ranty period from the date o f purchase from N-TRON or its au thorized reseller. If a produ ct does not operate as w arranted during t ...
¿Tienes una pregunta acerca de N-Tron 400 Series?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con N-Tron 400 Series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con N-Tron 400 Series probablemente compartirá una forma de solucionarlo.