-
Shure BETA54 - page 1
Subminiature Condenser Headw orn Microphones Models BET A 53 ™ , BET A 54 ™ User Guide BET A 54 BET A 53 ...
-
Shure BETA54 - page 2
English: page 1 Fr ançais: page 11 Deutsch: Seite 21 Español: Pág ina 31 Italiano: Pagina 41 ...
-
Shure BETA54 - page 3
1 English Introduction Shure models BET A 53 ™ and BETA 54 ™ ar e subminiature, electret condenser head worn micr ophones. They provide uncompromised sound quality and reliability with minimal visibility in applications such as broadcast, theater , and touring. Despite their small size , each microphone’ s condenser element delivers full , cl ...
-
Shure BETA54 - page 4
2 English Av ailable Models BET A 53 MODELS • Omnidirectional • For broadcast and stage BET A 54 MODELS • Supercardioid • For stage and vocal performance BET A 53 • Black fi nish • Detachable in-line preamp for wired applications • Requires phantom power WBH53B • Black fi nish • T A4F connector for wireless applications WBH53T ? ...
-
Shure BETA54 - page 5
3 English 1 2 3 4 5 Adjusting the Headband and Microphone 1 Adjust headband width 2 Adjust boom height 3 Adjust boom length 4 Do not attempt to bend the microphone boom! 5 “Roll” the boom for subtle adjustments of microphone position ...
-
Shure BETA54 - page 6
4 English Using the Windscreens and P rotective Caps Grip the internal frame of the windscreen fi rmly when connecting or removing. Do not pull on the foam itself . • T o connect, push the windscreen until it snaps into place over the cartridge. • T o remove, pull the windscr een directly off of the car tridge. Always use the BET A 54 with th ...
-
Shure BETA54 - page 7
5 English W earing the BE T A 53 and BET A 54 ...
-
Shure BETA54 - page 8
6 English 13 mm (.5 in.) 13 mm (.5 in.) P ositioning the Microphone BET A 53 BET A 54 • Position the omnidirectional BET A 53 microphone near the corner of the mouth • If necessary, roll the boom to avoid c ontact with skin and facial hair • Point the unidirectional BET A 54 microphone at the corner of the mouth ...
-
Shure BETA54 - page 9
7 English 1 2 3 4 5 W earing the M icrophone on Either Side All models may be worn with the microphone on the left or the right. • Carefully detach the boom holder (1), logo pad (2), and microphone cable (3) from the headband. • Reattach the boom holder to the opposite side of the wire frame (4). • Reattach the logo pad (5) and microphone cab ...
-
Shure BETA54 - page 10
8 English Component Black T an 1 Foam W indscreen (5 pieces) RPM304 RPM306 2 Standard Protective Cap (gold mesh) (5 piec es) RPM208 RPM212 Filtered P rotective Cap* (silver mesh) (5 pieces) RPM220 RPM214 3 Microphone/Boom Assembly with T A4F Con- nector (1 piece) RPM132 RPM134 4 Swiveling Lapel Clip (5 pieces) RPM510 RPM512 5 Boom Holder and Logo P ...
-
Shure BETA54 - page 11
9 English Component Black T an 1 Microphone/Boom Assembly with T A4F Con- nector (1 piece) RPM646 RPM648 2 Standard Protective Cap (gold mesh) (5 piec es) RPM208 RPM212 3 Snap-fi t Foam Windscreen (4 pieces) RPM316 RPM318 4 Swiveling Lapel Clip (5 pieces) RPM510 RPM512 5 Boom Holder and Logo Pad (2 each) RPM570 RPM580 6 Headband (1 piece, with boo ...
-
Shure BETA54 - page 12
10 English Specifications BET A 53 BET A 54 Specifi cation Wired Wireless Wired Wireless Type C ondenser (electret bias) Condenser (electret bias) Frequency Response 20Hz to 20KHz (see page 52) 50Hz to 20KHz (see page 52) Polar Pa ttern Omnidirectional (see page 52) Supercardioid (see page 52) Output Noise (equivalent dBSPL, A-weighted) 39.0 dB ty ...
-
Shure BETA54 - page 13
51 P olar P atterns and F requenc y Response BET A 53 BET A 54 20 20000 1000 10000 50 100 9 8 7 6 5 4 3 29 8 7 6 5 4 3 2 +10 0 –10 Hz dB –20 +20 20 20000 1000 10000 50 100 9 8 7 6 5 4 3 29 8 7 6 5 4 3 2 +10 0 –10 Hz dB 15 mm (.6 in) 6 0 6m m( 2f t ) +20 –20 –30 0º 125º Standard Cap 1 Filtered C ap 2 1 Capuchon standard 2 Capuchon à fi ...
-
Shure BETA54 - page 14
52 Wiring and C ertification Microphone Cartridge 5 Case (ground) 4 Shield (ground) 3 Red 1 (+5Vdc) Black (audio out) 2 Wireless T est Circuit 6 +5Vdc 100k 20k 1.0 uf 1 2 3 4 1 2 3 4 2SK1109 1. Rouge 2. Noir (sortie audio) 3. Blindage (masse) 4. Corps (masse) 5. Capsule de microphone 6. Circuit d’ essai sans fi l + – Eligible to bear CE markin ...
-
Shure BETA54 - page 15
©2005 Shure Incorporated 27F3115 (Rev. 6 ) Patent Notice: P atent Des. 451,902 SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Car ibbean: 58 00 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone : 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 8 47-600-6446 Eur ope, Middle East, Africa: Shu re Europe GmbH, Phone: ...
¿Tienes una pregunta acerca de Shure BETA54?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Shure BETA54, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Shure BETA54 probablemente compartirá una forma de solucionarlo.