-
Chicago Electric 47606 - page 1
1” SDS ROT AR Y HAMMER Model 47606 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our webs ...
-
Chicago Electric 47606 - page 2
SKU 47606 For technical questions, please call 1-800-444-3353. Page 2 Specications Chuck Capacity 1 Inch Power 120 V , 60 Hz, 1.13 HP , 850 W atts Amperage 6.8 Peak Amps, 4.6 Working Amps RPM 900 Blows per minute 3,200 Accessories: Break Point (Bull) Bit, Flat Head Chisel, Depth Rod, Lubricant, Masonry Drill Bits (10mm, 9/16”, 7/8”), Extra B ...
-
Chicago Electric 47606 - page 3
SKU 47606 For technical questions, please call 1-800-444-3353. Page 3 damaged, have them repaired by an authorized technician. The handles must be kept clean, dry , and free from oil and grease at all times. Disconnect power . Unplug tool when not in use. Remove adjusting keys and wrenches . Check that keys and adjusting wrenches are removed from t ...
-
Chicago Electric 47606 - page 4
SKU 47606 For technical questions, please call 1-800-444-3353. Page 4 - Lead from lead-based paints - Crystalline silica from bricks and cement or other masonry products - Arsenic and chromium from chemically treated lumber Y our risk from these exposures varies, depending on how often you do this type of work. T o reduce your exposure to these che ...
-
Chicago Electric 47606 - page 5
SKU 47606 For technical questions, please call 1-800-444-3353. Page 5 Assembly Refer to Figure 1. 1. Fit the Handle Band (508) over the front of the housing above the Bit Sleeve and screw the Handle (506) clockwise to secure. At this point do not fully tighten. 2. Rotate the Handle (506) around the tool until it rests on a at spot on the housing ...
-
Chicago Electric 47606 - page 6
SKU 47606 For technical questions, please call 1-800-444-3353. Page 6 REV 07c; 07j Main Handle (89) Handle (505) Knob (701) Switch (86) Bit Drill Stop (504) Bit Sleeve FIGURE 3 Brush Cap (70) Bit Sleeve FIGURE 2 Note: Break Point (Bull) Bits and cold chisels are to be used when the Selector Switch is in the hammering position only . Using these bit ...
-
Chicago Electric 47606 - page 7
SKU 47606 For technical questions, please call 1-800-444-3353. Page 7 REV 03d, 07c Operation Note: Make sure unit is not plugged in. Note: If you wish, you may attach a Dust Cap for overhead drilling applications. T o do so, after you install a bit, before you tighten the Bit Sleeve, slide the Dust Cap over the bit and adjust the Drill Stop so that ...
-
Chicago Electric 47606 - page 8
SKU 47606 For technical questions, please call 1-800-444-3353. Page 8 T roubleshooting and Maintenance Note: Other than changing or cleaning the carbon brushes, all internal repairs should be done by a qualied service technician. Problem Cause Action Motor doesn’t rotate when switched on. Disrupted power Poor switch contact Armature or eld ...
-
Chicago Electric 47606 - page 9
SKU 47606 For technical questions, please call 1-800-444-3353. Page 9 Parts List Part Description 1 O-ring 2 Steel Ball 3 Cylinder 4 Flat Pin 5 Striker 6 O-ring 706 Spring 7 Cone Gear 7D Steel Retaining Ring 51 1 Oil Bearing 8 Piston 9 Piston Pin 10 Connecting Rod 1 1 Needle Bearing 12 O-ring 13 O-ring 14 Oil Seal Cap 16 Nameplate 18 Bolt 19* Sprin ...
-
Chicago Electric 47606 - page 10
SKU 47606 For technical questions, please call 1-800-444-3353. Page 10 1 2 3 4 5 6 706 7 7D 51 1 6 8 9 10 1 1 12 13 14 16 701 702 703 704 705 501 503 504 505 506 507 508 509 47 48 49 50 51 52 53 54 55 56 36 37 38 39 40 41 41 42 42 43 44 45 46 89 90 19 91 66 92 93 18 19 20 21 22 23 24 25 26 27 28 29 30 30 31 32 33 34 35 57 58 60 61 64 65 66 19 67 68 ...
-
Chicago Electric 47606 - page 11
SKU 47606 For technical questions, please call 1-800-444-3353. Page 1 1 PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PROVIDED THE P ARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONL Y . NEITHER THE MANUF ACTURER NOR DISTRIBUTOR MAKES ANY REPRESENT A TION OR WARRANTY OF ANY KIND TO THE BUYER THA T HE OR SHE IS QUA ...
¿Tienes una pregunta acerca de Chicago Electric 47606?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Chicago Electric 47606, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Chicago Electric 47606 probablemente compartirá una forma de solucionarlo.